Related Manuals for Zline EL DORADO Series
Summary of Contents for Zline EL DORADO Series
- Page 1 Installation and User Manual SHOWER SYSTEMS BLISS & EL DORADO www.zlinekitchen.com...
- Page 2 ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to providing you an elevated experience in the heart of your home. With an endless selection of...
- Page 3 ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone’s homes. Because we continually strive to improve our products, we may change specifications and designs without prior notice.
-
Page 4: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION BLISS SHOWER SYSTEM BLISS TUB FILLER BLISS SHOWER FAUCET EL DORADO SHOWER SYSTEM EL DORADO SHOWER FAUCET CARE AND MAINTENANCE TROUBLESHOOTING... -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION PRIOR TO INSTALLATION • Make sure that the cold and hot water lines are turned off. • Wrap all threaded connections with Teflon tape. Always wrap in a clockwise direction. • Cover your drain to avoid losing parts. •... - Page 6 IMPORTANT SAFETY INFORMATION TOOLS NEEDED: • Wrench • Screwdriver • Hammer • Drill TIME REQUIRED: +/- 120 minutes LEGEND: Hot water Cold water Torch Warning Plumber’s tape...
-
Page 7: Bliss Shower System
BLISS SHOWER SYSTEM BEFORE INSTALLATION 1. Flange cover 2. Shower arm 3. Top spray shower 4. Wall valve body 5. Faceplate 6. Sleeve 7. Washer 8. Tooth 9. Screw 10. Handle 1 1. Handle 12. Flange cover 13. Angle valve 14. - Page 8 BLISS SHOWER SYSTEM BEFORE INSTALLATION...
- Page 9 BLISS SHOWER SYSTEM INSTALLATION Slide the sleeves onto the pipes and then Solder the copper together. insert pipes into the wall valve. Tighten the ring around the pipes with the wrench. NOTE: If soldering is involved, you must remove the internal valve components prior to the soldering.
- Page 10 BLISS SHOWER SYSTEM INSTALLATION After soldering, purge the water supply system Reinstall the valve components into their original for 30 seconds. positions. Use this diagram to understand the placement Screw the wall valve body into the system with of the wall valve. a screwdriver.
- Page 11 BLISS SHOWER SYSTEM INSTALLATION Screw the sleeve and washer into the wall valve Attach the faceplate and remove the plastic. body. Attach the water control handle. Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
- Page 12 BLISS SHOWER SYSTEM INSTALLATION Twist the top spray shower into the shower arm. Connect the angle valve to the flange cover and screw together. Secure with plumber’s tape to prevent leaks. Use a pencil to mark the mounting holes on the Screw the shower rail into the wall.
- Page 13 BLISS SHOWER SYSTEM OPERATION Review the diagram to understand the hot, cold, Connect the shower handle to the shower rail. Tighten and open settings. with a wrench.
-
Page 14: Bliss Tub Filler
BLISS TUB FILLER BEFORE INSTALLATION 1. Rough-in 2. Sleeve 3. Faceplate 4. Cap 5. Handle 6. Spout 7. Screw... - Page 15 BLISS TUB FILLER INSTALLATION Mark on the wall where you want the faucet to Use a screwdriver to screw the faucet onto the be installed. wall. Attach the hose using plumbing tape and a Place the components in the appropriate wrench.
- Page 16 BLISS TUB FILLER INSTALLATION Screw the sleeve and washer into the wall valve Make sure that the components are aligned body. properly. Tighten the components. Take off the protective shield.
- Page 17 BLISS TUB FILLER INSTALLATION Attach faucet to base plate. Attach base plate to wall. Attach handle to the fixture. Review the diagram to understand the hot, cold, and open settings.
-
Page 18: Bliss Shower Faucet
BLISS SHOWER FAUCET BEFORE INSTALLATION 1. Flange cover 2. Shower arm 3. Top spray shower 4. Wall valve body 5. Faceplate 6. Sleeve 7. Cap 8. Switch handle... - Page 19 BLISS SHOWER FAUCET INSTALLATION Slide the sleeves onto the pipes and then Solder the copper together. insert pipes into the wall valve. Tighten the ring around the pipes with the wrench. NOTE: If soldering is involved, you must remove the internal valve components prior to the soldering.
- Page 20 BLISS SHOWER FAUCET INSTALLATION After soldering, purge the water supply system Reinstall the valve components into their original for 30 seconds. positions. Use this diagram to understand the placement Place the components in the appropriate of the wall valve. location.
- Page 21 BLISS SHOWER FAUCET INSTALLATION Screw the sleeve and washer into the wall valve Attach the face plate and remove the plastic. body. Attach the water control handle. Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
- Page 22 BLISS SHOWER FAUCET INSTALLATION Twist the top spray shower into the shower arm. Review the diagram to understand the hot, cold, and open settings.
-
Page 23: El Dorado Shower System
EL DORADO SHOWER SYSTEM BEFORE INSTALLATION 1. Flange cover 2. Shower arm 3. Top spray shower 4. Wall valve body 5. Faceplate 6. Sleeve 7. Washer 8. Tooth 9. Screw 10. Handle 1 1. Handle 12. Flange cover 13. Angle valve 14. - Page 24 EL DORADO SHOWER SYSTEM BEFORE INSTALLATION...
- Page 25 EL DORADO SHOWER SYSTEM INSTALLATION Slide the sleeves onto the pipes and then insert Solder the copper together. pipes into the wall valve. Tighten the ring around the pipes with the wrench. After soldering, purge the water supply system Reinstall the valve components into their original for 30 seconds.
- Page 26 EL DORADO SHOWER SYSTEM INSTALLATION Screw the wall valve body into the system with Place the components in the appropriate a screwdriver. Do not overtighten. location. Screw the sleeve and washer into the wall valve Attach the face plate and remove the plastic. body.
- Page 27 EL DORADO SHOWER SYSTEM INSTALLATION Attach the water control handle. Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks. Twist the top spray shower into the shower arm. Connect the angle valve to the flange cover and screw together.
- Page 28 EL DORADO SHOWER SYSTEM INSTALLATION Use a pencil to mark the mounting holes on the Connect the components of the shower rail. wall. Use a hammer to put the screws in. Screw the shower rail into the wall. Connect the shower handle to the shower rail. Tighten with a wrench.
- Page 29 EL DORADO SHOWER SYSTEM INSTALLATION Review the diagram to understand the hot, cold, and open settings.
-
Page 30: El Dorado Shower Faucet
EL DORADO SHOWER FAUCET BEFORE INSTALLATION 1. Flange cover 2. Shower arm 3. Top spray shower 4. Wall valve body 5. Faceplate 6. Sleeve 7. Cap 8. Switch handle... - Page 31 EL DORADO SHOWER FAUCET INSTALLATION Slide the sleeves onto the pipes and then insert Solder the copper together. pipes into the wall valve. Tighten the ring around the pipes with the wrench. NOTE: If sol- dering is involved, you must remove the internal valve components prior to the soldering.
- Page 32 EL DORADO SHOWER FAUCET INSTALLATION After soldering, purge the water supply system Reinstall the valve components into their original positions. for 30 seconds. Use this diagram to understand the placement Place the components in the appropriate of the wall valve. location.
- Page 33 EL DORADO SHOWER FAUCET INSTALLATION Screw the sleeve and washer into the wall valve Attach the face plate and remove the plastic. body. Attach the water control handle. Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
- Page 34 EL DORADO SHOWER FAUCET INSTALLATION Twist the top spray shower into the shower arm. Review the diagram to understand the hot, cold, and open settings.
-
Page 35: Care And Maintenance
CARE AND MAINTENANCE CARE AND MAINTENANCE To keep the product clean and shining, follow the steps below: 1. Rinse clean with water and dry with a soft cloth. 2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners. 3. -
Page 36: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTIONS Unscrew the lever on the handle by hand. Loosen set screw with an Allen/hex There is leakage under The locking nut has come loose. key. Remove the handle and the handle. unscrew trim cap by hand. Tighten locking nut with an adjustable wrench. - Page 37 WARRANTY COVERAGE ZLINE Kitchen and Bath faucets have a limited lifetime warranty from the original purchase date for the original purchaser of the product. TERMS This warranty applies only to the original purchaser of a faucet installed for normal residential use. This is defined as a single-family, residential dwelling in a non-commercial setting.
- Page 38 Customer Experience Portal. Scan the QR code to view the most up-to-date version of our user manual and installation guide. Need to purchase a part or accessory for your ZLINE product? Visit www.zlineparts.com, ZLINE’s official parts distribution partner.
- Page 39 4.0.0 www.zlinekitchen.com 1-614-777-5004 contact@zlinekitchen.com...
Need help?
Do you have a question about the EL DORADO Series and is the answer not in the manual?
Questions and answers