Local Codes; Product Features; Pre-Installation Preparation - Desa (V)CD36RNE Owner's Operation And Installation Manual

LOCAL CODES

Install and use fireplace with care. Follow all local
codes. In the absence to local codes, use the cur-
rent National Fuel Gas Code ANSI Z223.1/NFPA
54* (USA) or the current CSA-B149.1 Installation
Code (Canada).
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269

PRODUCT FEATURES

These are a few facts that can help you understand
and enjoy your direct-vent fireplace:
• The CD36R dedicated rear vent is best suited
for flush or corner installations when vented
horizontally through an exterior wall.
• The CD36T dedicated top vent is suited for
any application where height is necessary to
terminate the venting system either through
the roof (vertical) or to gain sufficient height
and offset to vent to an outside/exterior wall
(horizontal).
• The vent pipe installation is very important to
allow for proper operation. You must select
the appropriate unit for your application and
follow the venting instructions to plan your
installation.
• This fireplace may be installed in any room of
your house provided all local codes and these
installation instructions are followed.
• Models (V)CD36R/T are equipped with a mil-
livolt gas control system that does not require
electricity to operate. A piezo ignitor is provided to
light the pilot without using matches or lighters.
• Models (V)CD36RE/TE are equipped with an
electronic ignition system that requires 120VAC
to operate. An electrode ignitor automati-
cally lights the pilot flame when the fireplace
is turned on.
• All models can accept an optional circulating
air blower when 120 VAC connection is sup-
plied. If you plan to install an optional blower,
do not forget to wire the fireplace outlet when
framing.
• Each time you turn on your fireplace, you may
notice some amount of condensation on the in-
side of the fireplace glass. This is normal and will
disappear after 10-20 minutes of operation.
116035-01E
• Your direct-vent gas fireplace system (fireplace
and venting) is a balanced and sealed gas oper-
ating unit. It is highly efficient because it uses
outside air for combustion while independently
heating the indoor air.
PRE-INSTALLATION
LOCATION AND SPACE
REqUIREMENTS
Determine the safest and most efficient location
for your DESA direct-vent fireplace. Make sure
that rafters and wall studs are not in the way of the
venting system. Choose a location where the heat
output is not affected by drafts, air conditioning
ducts, windows or doors. Figure 2 shows some
common locations. Be aware of all restrictions and
precautions before deciding the exact location for
your fireplace and termination cap.
When deciding the location of your fireplace,
follow these rules:
• Do not connect this fireplace venting to a chim-
ney flue serving a separate solid-fuel burning
fireplace or appliance.
• Due to high temperatures, do not locate this
fireplace in high traffic areas, windy or drafty
areas or near furniture or draperies.
• Proper clearances must be maintained.
• If your fireplace is to be installed directly on
carpeting, vinyl tile or any combustible material
other than wood, it must be installed on a metal
or wood panel extending the full width and depth
of the fireplace. See Figure 3, page 6.
• Your fireplace is designed to be used in zero clear-
ance installations. Wall or framing material can be
placed directly against any exterior surface on the
back, sides or top of your fireplace, except where
standoff spacers are integrally attached. If standoff
spacers are attached to your fireplace, these spac-
ers can be placed directly against wall or framing
material. See framing details on page 7.
Through exterior wall
enclosed in a chase
Figure 2 - Common Fireplace Locations
www.desatech.com
PREPARATION
Corner
Flush with
installation
a wall
5