Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Wall Mantel with Base and Trim
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Important: Read entire instruction sheet before as-
sembling or installing mantel kit.
This mantel is only approved for use with CDCF, CGCF,
EFS, FDCF, HDCF, VDCF and VMH Series fireplaces. Do
not use mantel with any other product.
This mantel kit contains the following pieces:
• Hardware package
• Trim kit
• Trim kit hardware
The hardware package contains the following:
• 2 - 3" screws
• 20 - 1
⁄
" screws
1
4
Tools and items required:
• #2 Phillips screw driver (regular length)
• Slotted screw driver
• Measuring tape
• PENCIL
WS26CP and WD26CP
117197-03
GAB6094
102866-01
www.desatech.com
If any wood pieces are missing or damaged, contact the
dealer where you purchased this mantel for replacement.
If hardware is missing or damaged, contact DESA Heating
Products at 1-866-672-6040 for referral and warranty infor-
mation. You can also visit DESA Heating Products' technical
service web site at www.desatech.com.
Note: Place all mantel pieces together before actually as-
sembling mantel.
WARNING: Only use 1
header and top. Damage to the mantel will result if the
longer screws provided are used for this purpose.
/
" screws to assemble
1
4
Advertisement
Table of Contents
Related Manuals for Desa Wall Mantel with Base and Trim WD26CP
Summary of Contents for Desa Wall Mantel with Base and Trim WD26CP
-
Page 1: Assembly And Installation Instructions
If any wood pieces are missing or damaged, contact the dealer where you purchased this mantel for replacement. If hardware is missing or damaged, contact DESA Heating Products at 1-866-672-6040 for referral and warranty infor- mation. You can also visit DESA Heating Products' technical service web site at www.desatech.com. -
Page 2: Assembling Mantel
AsseMblING MANTel Important: More than one person is required to lift assembled mantel. lift mantel by leg assemblies. lifting by header or mantel top could damage mantel. 1. Some models require side/corner assembly. For these models, lay leg side on floor. Position leg as shown in Figure 1. - Page 3 Screws Mantel Base Figure 5 - attaching mantel assembly to Base AsseMblING TRIM 1. Remove packaging from three pieces of trim. 2. Locate two adjusting plates with set screws, and two shims in the hardware packet. 3. Align shim under adjusting plate as shown in Figure 6. 4.
- Page 4 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 Technical Service and Parts: 1-866-672-6040...
- Page 5 Si faltan piezas de ferretería o están dañadas, comuníquese con DESA Heating Products al 1-866-672-6040 para obtener información de consulta y sobre la garantía. También puede visitar el sitio web de servicio técnico de DESA Heating Products en www.desatech.com.
- Page 6 ensamble de la repisa de chimenea Importante: se requiere más de una persona para levantar la repisa montada. levante la repisa de chime- nea sujetándola por los ensambles de ambos tramos. si levanta la repisa de chimenea por la cabecera o por su parte superior, podría dañarla.
- Page 7 Tornillos Base de la repisa Figura 5 - Fijación del ensamble de la repisa de chimenea a la base ensamble del adorno 1. Retire el embalaje de las tres piezas del adorno. 2. Localice dos placas de ajuste con su juego de tornillos y dos bases para nivelar en el paquete de piezas.
- Page 8 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004, EE.UU. Servicio técnico y piezas: 1-866-672-6040 117148-01 117148 01 Rev. C NOT A UPC 09/05...