JVC SR-9168U - 168 Hour Realtime/high Density Recorder Instructions Manual page 19

5 SETTING OF THE FUNCTION MENU SWITCHES
5-2 Contents of the Function Menu Switches
Screens Items
VTR mode 1 INDEX
setting SEARCH
CAMERA SW
TAPE END
BUZZER
WARNING
BUZZER
VTR mode 2 SUMMER TIME
setting
TERMINAL
SEL 1
TERMINAL
SEL 2
REC REMAIN
[ ]: Factory setting
Set values
[OFF] Enables or disables the Index Search function.
ON OFF : The index search function is disabled.
ON : When an alarm-recorded tape is put in the FF or REW Shuttle Search
mode, the VCR searches for the nearest recorded index code (VISS
signal) and engages playback at the indexed position.
When an alarm-recorded tape is fast-forwarded or rewound, the VCR
searches for the nearest index code and enters the Stop mode at the
indexed position.
[OFF] Sets the camera switching interval for output to an external sequential switcher
1 FIELD during recording.
OFF : No camera switching signal is output.
1 FRAME
1 FIELD : Set to this position to switch the camera every 1 field.
1 FRAME: Set to this position to switch cameras every 1 frame.
[OFF] Turns the Tape End buzzer on or off.
ON OFF : The buzzer does not sound at tape end.
ON : When the tape reaches the position set with the <REC REMAIN> menu
function switch during recording (tape end, or 3 minutes or 6 minutes
before the tape ends during 6H mode ), a buzzer sounds.
To stop the buzzer sound, press the [REW] button, [EJECT] button or
[POWER] button.
When the mode is changed, the buzzer sound stops.
[OFF] Turns the warning buzzer on or off.
ON OFF : The buzzer does not sound.
ON : The buzzer sounds.
[OFF] Turns summer time compensation on or off.
ON OFF : Clock is not adjusted for summer (daylight saving) time.
ON : Clock is adjusted for summer (daylight saving) time.
[SERIES] Select the signal to be input or output to the [SERIES/CLOCK IN·OUT]
EXT
terminals on the rear panel.
C.ADJ SERIES : Set to this position to input or output a series recording signal.
EXT : Set to this position to start or stop the recording with the VCR
activation signal input from an external control device.
C.ADJ : Set to this position to input or output a clock reset signal.
[WARN.] Select the signal output from the rear panel's [WARNING/REC OUT] terminal.
REC
WARN. : Set to this position to output a warning signal. The warning signal is
output if an abnormality occurs in tape transport or mechanism
operation.
REC : Set to this position to output a recording mode signal (+12 V) in the
Record mode.
[OFF] Sets the timing to process tape end before the actual tape end. This menu
180S switch setting is effective in the 6H to L30H Record modes. For the 48H to
360S
240H modes, set with <COUNT END>. The following operations are executed
at the timing set with this menu switch.
• The tape end signal is output from the rear panel's [TAPE END] terminal.
• The series recording signal is output from the rear panel's [CLOCK/SERIES
OUT] terminal (with the TERMINAL SEL 1> function menu switch set to
"SERIES").
• The tape end buzzer sounds (with the <TAPE END BUZZER> function menu
switch set to "ON").
• "End" is shown on the counter display.
The set values (180S/360S) are for the 6H mode. The relation between the
recording mode and the recording time is shown below.
These values should be used as a reference only. Actual values may differ depending on
the tape used.
Function
Record modes
Setting
6H L18H
OFF Tape end Tape end
180S 3 minutes 9 minutes
360S 6 minutes 18 minutes
L30H
Tape end
15 minutes
30 minutes
19