Ltc 0498 series dinion2x day/night camera (6 pages)
Summary of Contents for Bosch LTC 1461-21
Page 1
Flexidome series Installation manual Installatiehandleiding Vandal resistant Vandaalbestendige surveillance dome dome- bewakingscamera Manuel d'installation Dôme de surveillance Manuale d'installazione antivandalisme Dome di Installationshandbuch sorveglianza Vandalismusresistente Antivandalismo Überwachungskuppel Manual de instalação Manual de instalación Dome de vigilância Domo de vigilancia antivandalismo antivandálico...
5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Bosch Security Systems | 2005-02 | V2.0...
Page 3
Unauthorized substitutions may result in fire, electric shock or other hazards. 17. Safety Check: Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition. Bosch Security Systems | 2005-02 | V2.0...
For additional information or to speak to a representative, please contact the Bosch Security Systems location nearest you or visit our web site at www.boschsecuritysystems.com Bosch Security Systems | 2005-02 | V2.0...
• Adapter plate • Lens adjustment cap • Installation manual Note If equipment appears to have been damaged during shipment, repack it in the original packaging and notify the shipping agent or supplier. Bosch Security Systems | 2005-02 | V2.0...
Page 6
• Unscrew the dome counterclockwise and remove it from the base together with the sealing ring. • Remove the inner liner by depressing the two retention tabs near the base of the liner. Bosch Security Systems | 2005-02 | V2.0...
The following drawings show the different ways of mounting the unit. Figure 4-1 Rear connection - solid surface Wires Solid surface (four pre-drilled 8mm holes) Mounting base Four screws (supplied) Bosch Security Systems | 2005-02 | V2.0...
Page 8
Adapter plate Thin surface (for example, a suspended ceiling) Mounting base Four screws (M5, not supplied) Figure 4-3 Connection to an electrical box Electrical box Adapter plate Mounting base Four screws (M5, supplied) Bosch Security Systems | 2005-02 | V2.0...
Page 9
Figure 4-5 Raised mounting - rear connection Wires Conduit Solid surface (four pre-drilled 8mm holes) Raised Four screws mounting base (supplied) (LTC 1347/00) Four screws Camera unit (M5, supplied) and base Bosch Security Systems | 2005-02 | V2.0...
Page 10
Run the power and video wires through separate rubber grommets into the connection box area. Note In order to ensure a watertight cable entry, use round cables of between 5 and 6 mm (0.2 - 0.24 inch) for power and video connection. Bosch Security Systems | 2005-02 | V2.0...
• Push the connections back through the surface wire hole. • Secure the mounting base to the surface with four screws. Bosch Security Systems | 2005-02 | V2.0...
This jack provides a composite video signal, via the optional cable S1460 (2.5 mm plug to BNC female). Monitor jack Focus Thumbwheels Focal length V-phase adjust DIP switches Bosch Security Systems | 2005-02 | V2.0...
To obtain a horizontal horizon (for tilted ceilings or sidewall mounting), rotate the base of the lens as necessary to align the picture shown on the monitor. Do not rotate more than 360°. Bosch Security Systems | 2005-02 | V2.0...
Place the sealing ring and the trim ring over the dome. • Align the tamper resistant screw in the trim ring with a thread hole in the mounting base. • Use the special screwdriver supplied to tighten the tamper resistant screw. Bosch Security Systems | 2005-02 | V2.0...