Advertisement
Quick Links
WIRELESS-MICROPHONE SYSTEMS
CPR30 – Frequencies programming
Remove CPR30 battery pack: to do it remove "AA" cells and remove two screws near the corners of battery pack. Extract battery pack.
Insert UPK32/100 connector on ST3 (ST3 before used by battery pack).
After a successfully programming, disconnect UPK32/100 and remount CPR30 battery pack.
CPR30-howtoprogramCS029112.doc
WISYCOM S.r.l.
•
Via Spin, 156
•
I-36060 Romano d'Ezzelino (VI)
•
Italy
Tel. +39 0424 382605
•
Fax +39 0424 382733
•
www.wisycom.com
•
e-mail: sales@wisycom.com
Advertisement
Related Manuals for WisyCom RPU300 UHF
Summarization of Contents
CPR30 Frequency Programming
Battery Pack Removal
Remove the battery pack by taking out "AA" cells and screws.
UPK Connector Insertion
Insert the UPK32/100 connector onto ST3.
Post-Programming Disconnection
Disconnect UPK32/100 and re-mount the battery pack.
CRT14 Frequency Programming
Device Opening Procedure
Open the device by removing screws retaining the mechanical body.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CRT16 Frequency Programming
Device Opening Procedure
Open the device by removing screws retaining the mechanical body.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CRT16 Frequency Programming
Device Opening Procedure
Open the device by removing screws retaining the mechanical body.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CSR50 Frequency Programming
Device Opening Procedure
Open the device by removing screws retaining the mechanical body.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CST36 & CST50 Frequency Programming
Device Opening and Shield Removal
Open device, remove RF shield SC1 on CST36, operate on top side.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CST38 Frequency Programming
Device Opening Procedure
Open device by removing screws retaining the mechanical body.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
CST910 Frequency Programming
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
MCR40 Frequency Programming
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
MSR918 UHF Frequency Programming
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
MSR916 & MSR918 VHF Frequency Programming
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
MTH200 Frequency Programming
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
MTP22 Frequency Programming
Battery Pack Removal
Remove the battery pack by taking out "AA" cells and screws.
UPK Connector Insertion
Insert the UPK32/100 connector onto ST5.
Post-Programming Disconnection
Disconnect UPK32/100 and re-mount the battery pack.
RTE25-VHF & RPU300 VHF Frequency Programming
Device Opening and Board Handling
Open device, operate on powered off circuit board, do not remove boards.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
RTE25-UHF & RPU300 UHF Frequency Programming
Device Opening and Board Handling
Open device, operate on powered off circuit board, do not remove boards.
UPK Connector Connection
Connect UPK32/UPK100 to circuit board pads for programming.
Programming Pad Verification
Verify unobstructed programming pads before inserting UPK connector.
Need help?
Do you have a question about the RPU300 UHF and is the answer not in the manual?
Questions and answers