Table of Contents
Advertisement
Quick Links
Fisher Engineering
50 Gordon Drive, Rockland, Maine 04841‑2139 • www.fisherplows.com
HS Compact Plow
Blade and Off‑Truck Kit
Installation Instructions
CAUTION
Read this document before installing the
snowplow.
CAUTION
See your FISHER
outlet/website for specific
®
vehicle application recommendations before
installation. The eMatch selection system has
specific vehicle and snowplow requirements.
A DIVISION OF FISHER, LLC
85280, 85285
85240, 85240‑3
July 15, 2020
Lit. No. 85309, Rev. 03
Advertisement
Table of Contents
Related Manuals for Fisher 85280
Summarization of Contents
SAFETY
Safety Definitions
Explains the meaning of WARNING, CAUTION, and NOTE labels used in the document.
Warning and Instruction Labels
Details the various warning, caution, and instruction labels found on the snowplow, including serial number information.
Attachment and Detachment Procedures
Provides step-by-step instructions for attaching and detaching the snowplow to the vehicle.
Safety Precautions
General Operating Safety
Covers essential safety rules for operating the snowplow, including blade movement and bystander safety.
Hydraulic System Safety
Outlines critical safety measures when working with the hydraulic system, including fluid pressure and hose inspection.
Electrical and Fuse Safety
Details safety considerations for the electrical system, including fuse replacement guidelines.
Personal Safety Measures
Advises on personal protective equipment and safe practices during installation and service, like wearing safety goggles.
Environmental and Operational Safety
Fire and Explosion Hazards
Warns about the flammability of gasoline and precautions to prevent fires and explosions.
Cell Phone Usage and Distractions
Emphasizes driver responsibility to avoid distractions while operating the vehicle.
Ventilation and Noise Exposure
Discusses risks associated with vehicle exhaust fumes and airborne noise emissions from the snowplow.
Battery Safety Precautions
Provides essential safety guidelines for handling batteries, including acid hazards and electrical disconnection.
Fastener Torque Specifications
Lists recommended torque values for various inch and metric fasteners used in assembly.
INSTALLATION INSTRUCTIONS
Unpacking Components
Guides on how to unpack the snowplow parts and set them aside safely.
A-Frame to Blade Assembly
Details the process of connecting the A-frame to the blade assembly, including pivot tube and trip bumper installation.
Assembly Steps
Rubber Bumpers and Angle Ram Installation
Instructions for installing rubber bumpers, angle rams, and securing the stand for the snowplow.
Blade Guide and Cutting Edge Securing
Covers the installation of blade guides and final securing of the cutting edge with hardware.
Receiver Installation
Describes how to install the snowplow receivers into the truck mount pockets.
Headlamp Installation
Vehicle Wiring and Headlamp Setup
Guides on connecting vehicle wiring and positioning headlamp channels and swivels.
Headlamp Attachment and Aiming
Details securing headlamps with correct hardware and the process for aiming headlamp beams.
Hydraulic Unit Setup
Attaching the Snowplow and Reservoir Installation
Instructions for attaching the snowplow to the vehicle and installing the hydraulic unit's breather.
Hydraulic Fluid Level Check and Adjustment
Procedures for checking and filling the hydraulic fluid reservoir to the correct level.
Blade Drop Speed Adjustment
Adjusting Blade Drop Speed
Explains how to adjust the blade drop speed using the quill in the valve manifold.
Final Inspection and Adjustment
Hose Routing and Inspection
Guides on inspecting and routing hydraulic hoses to prevent damage and pinching.
Hitch Pin Lubrication
Instructions for adding grease to the hitch pins for proper operation.
OPERATIONAL TEST AND FINAL ADJUSTMENTS
Plug Covers for Disconnection
Advises on using plug covers when the snowplow is disconnected from the vehicle battery.
Owner's Manual Packet Handling
Guidelines for delivering and attaching the Owner's Manual packet to the purchaser or control unit.
Need help?
Do you have a question about the 85280 and is the answer not in the manual?
Questions and answers