Table of Contents
Advertisement
INSTALLATION AND
SERVICING
PRO & SYSTEM READY
When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance
specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal.
For the very latest copy of literature for specification and maintenance practices visit our website www.idealboilers.com
where you can download the relevant information in PDF format.
ISSUE 03: SEPTEMBER 2017
Advertisement
Table of Contents
Related Manuals for IDEAL SYSTEM READY Series
Summarization of Contents
DESIGN
Manufacturer: Ideal Boilers
Details about the manufacturer, Ideal Boilers.
Maintenance
Procedures for maintaining the appliance.
Handling Before Installation
Guidance on safely handling the unit prior to installation.
The Environment
Information on the product's environmental impact.
Ideal Pro Indirect
Specific details pertaining to the Ideal Pro Indirect model.
Basic Appliance
Description of the standard appliance components.
Part G3 loose components supplied in a separate box
Listing of additional components provided with the unit.
TECHNICAL INFORMATION
Key technical specifications and data for the appliance.
NOTES
Important notes related to the design section.
INSTALLATION
General Design Considerations
Factors influencing the installation design.
Insulation of pipework
Recommendations for insulating pipework.
Mains Water Supply
Requirements for the mains water supply.
Model Selection
Guide for choosing the correct appliance model.
General Restrictions
Limitations and regulations for installation.
Pipe Layout
Recommended pipe configurations and routing.
Plastic Pipework
Suitability and installation of plastic pipework.
Secondary Hot Water Circulation
Details on setting up secondary circulation.
Shower Fittings
Advice on shower installations.
Typical Discharge Pipe Arrangement
Diagram and explanation for discharge pipe setup.
Pressure & Temperature/expansion Relief Valve Pipework
Pipework details for safety valves.
Line Strainer
Information on the line strainer component.
Tundish
Function and placement of the tundish.
Expansion Vessels Installation
Guide for installing expansion vessels.
Combination Inlet Group
Description of the inlet group components.
Immersion Heater Wiring
Instructions for wiring immersion heaters.
Immersion Heaters
Details on immersion heater specifications.
Heating/primary Systems
Setup for heating and primary circuits.
Safety
Crucial safety information for installation.
Primary Circuit
Details regarding the primary heating circuit.
Sealed Primary Circuit
Specifics for sealed heating systems.
Gate Valve
Information on gate valve usage.
Fitting Blending Valves To The Unvented Ideal Pro Appliances
Guidance on installing blending valves.
(S-PLAN) WIRING DIAGRAM WITH TWO 2 PORT VALVES
Electrical schematic for S-Plan systems.
(Y-PLAN) WIRING DIAGRAM WITH 3 PORT VALVE/2 PORT SAFETY VALVE
Electrical schematic for Y-Plan systems.
(S-PLAN) WIRING DIAGRAM WITH TWO 2 PORT VALVES AND BOILER CONTROLLED PUMP OVERRUN OPTION
Advanced S-Plan wiring with pump overrun.
(Y-PLAN) WIRING DIAGRAM WITH 3 PORT VALVE/2 PORT SAFETY VALVE AND BOILER CONTROLLED PUMP OVERRUN OPTION
Advanced Y-Plan wiring with pump overrun.
COMMISSIONING
The final steps for system setup and verification.
SERVICING AND MAINTENANCE
IMPORTANT NOTE
Critical note for maintenance procedures.
Scale
Addressing scale buildup issues.
General
Routine checks and maintenance tasks.
Discharge From Relief Valves
Troubleshooting relief valve discharge.
FAULT FINDING
Comprehensive guide to diagnosing faults.
FAULT - No Hot Water (Direct)
Specific fault diagnosis for direct heating.
FAULT - No Hot Water (Indirect)
Specific fault diagnosis for indirect heating.
FAULT - Poor Water Flow at Hot Taps
Troubleshooting low water flow.
FAULT - Water Discharge Into Tundish
Diagnosing water discharge issues.
SHORT PARTS LIST
Reference for common spare parts.
IDEAL SYSTEM READY
Ideal System Ready Range
Overview of the System Ready product line.
Appliance Arrangement / Fitted Components
Details of pre-fitted components.
Additional Component Kit
Supplementary parts provided.
Potable System - Separate Components
Components for potable water systems.
Potable Water Expansion Vessel Sizes
Technical data for expansion vessels.
Fitting Template
Guide for initial pipework fitting.
Typical Arrangement / Connection Details
Diagram of system connections.
Notes
Important installation and safety notes.
Model Selection Data/Cupboard Sizes
Data for model selection and cupboard dimensions.
SPARE PARTS LIST - EXTRA COMPONENTS FOR THE 'SYSTEM READY' APPLIANCE
Specific spare parts list for System Ready.
Electrical
Electrical connection requirements.
APPENDIX A
Water Savings
Advice on reducing water consumption.
TAPS & MIXERS
Information on taps and mixers.
SHOWERS
Information on showers.
Options For Showers
Fitting options for showers.
4 Fixing Options For Taps & Mixers
Fixing options for taps and mixers.
APPENDIX B
MANUAL HANDLING OF APPLIANCE PRODUCTS
Guidelines for safe product handling.
Scope
Defines the scope of the manual handling assessment.
Main Hazards
Identifies potential hazards during lifting.
Control Measures
Safety measures for handling.
Manual lifting procedure
Steps for safe lifting.
Individual capability
Factors influencing lifting ability.
Residual risk
Remaining risks after safety measures.
TERMS AND CONDITIONS
Ideal Unvented Cylinder Warranty Terms and Conditions
Details of the product warranty.
Please note
Important notes regarding warranty terms.
We reserve the right to charge a call-out fee where:
Conditions for call-out charges.
USER GUIDE
WARNING
Critical safety warning for users.
DO NOT, at any time, tamper in any way with the safety valves or overheat thermostats/wiring.
Explicit instruction against tampering with safety devices.
Need help?
Do you have a question about the SYSTEM READY Series and is the answer not in the manual?
Questions and answers