Pin Assignment Of Dvi-I Terminal; Control Terminal - Toshiba TDP-T355 Owner's Manual

Specifications (Continued)

Pin assignment of DVI-I terminal

COMPUTER IN 1
C5 16
C4 C3 24 17 9
C2 C1 8
1
DVI digital & analog connector
Pin No. Pin description
1 T.M.D.S. data 2 –
2 T.M.D.S. data 2 +
3 T.M.D.S. data 2/4 shielded
4 T.M.D.S. data 4 – (N.C)
5 T.M.D.S. data 4 + (N.C)
6 DDC clock
7 DDC data
8 Analog vertical sync signal
9 T.M.D.S. data 1 –
10 T.M.D.S. data 1 +
11 T.M.D.S. data 1/3 shielded
12 T.M.D.S. data 3 – (N.C)
13 T.M.D.S. data 3 + (N.C)
14 +5V power source
15 GND +5V, H Sync & V Sync
Analog input signal
• Analog RGB input
RGB signals: 0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/P /P input
B R
Y signal: 1.0V (p-p) 75 Ω
P /P signals: 0.7V (p-p) 75 Ω
B R
Pin No. Pin description
16 Hot plug detection
17 T.M.D.S. data 0 –
18 T.M.D.S. data 0 +
19 T.M.D.S. data 0/5 shielded
20 T.M.D.S. data 5 – (N.C)
21 T.M.D.S. data 5 + (N.C)
22 T.M.D.S. clock shielded
23 T.M.D.S. clock +
24 T.M.D.S. clock –
C1 Analog video signal (R / P
C2 Analog video signal G / Y
C3 Analog video signal B / P
C4 Analog horizontal sync signal
C5 Analog GND R/P ,G/Y,B/P
R
58

CONTROL terminal

Pin assignment
7
8
5
2
Mini DIN 8 pin connector
Interface format
1 Communication method
2 Communication format
3 Data format
4 Replies
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
Main Commands
)
R
Item
Power on
B
Power off
Icon display on
B
Icon display off
Auto setting (RGB input)
Status display on
Status display off
Note
• Contact your dealer for control cable and other commands.
Pin No. Signal Name
1 RXD
6 2 CTS
3 DSR
4 GND
3
5 RTS
4 6 N.C
7 TXD
1
8 GND
RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length: 1 bit
STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
Acknowledge ACK (06h) CR (0Dh) Data
ACK (06h) ESC (1Bh)
No acknowledge NAK (15h)
Command
PON
POF
MO0
MO1
PAT
DON
DOF
59
Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
... Normally ended
... Aborted