Finishing The Wall Mounting; First Use; Operation - DEXAPLAN VT 623 - MANUAL 12-10-2007 Manual

When laying the cable through the wall, guide the
!
cable through the cable openings of the wall bracket
and the wedge shaped bracket [29/32].
Fix the wedge shaped bracket in place to the wall
!
using the four mounting screws [10] and wall plugs
[11].
Fix the wall bracket [16] to the wedge shaped bracket
!
using the four fixing screws [5].
Indoor station: Hanging on the wall without wall
bracket
The indoor station can also be hung on the keyhole slots
[49].
Drill two holes at the desired mounting position (Ø 5
!
mm) with horizontal spacing of 4.6 cm.
Insert two wall plugs [8] in the drilled holes.
!
Screw the two mounting screws [9] into the drilled
!
holes so that the screw heads protrude approx. 5 mm
from the holes.
Connections
Connecting the outdoor station to the indoor station
Remove the four screws of the outdoor station
!
terminal cover [23].
Lift the terminal cover at the tab [26].
!
Label the nameplate:
!
Remove the nameplate [61] completely from the
!
slot.
Label the nameplate. In doing so, note that only 4
!
cm are visible.
Slide it back into the slot as far as the stop.
!
Carefully make a hole using a pointed object in one of
!
the predetermined breaking points of the grommet
[24].
Guide the connection cable [14] through this hole.
!
If required, make a second hole for the cable of an
!
optional door opener and guide the cable through this
hole.
Connect the connection cable [14] to the terminals of
!
the outdoor station [59, 60] and the indoor station [55,
56] according to the connection diagram (see Fig. I).
Pay attention here to the wire markings and the
polarity (A to A, B to B).
If desired, connect an optional door opener [62] (see
!
next chapter).
Replace and screw down the terminal cover on the
!
outdoor station.
Connecting an optional door opener
If desired, install an optional door opener [62] (not
!
included in the package contents) at the desired
location according to the instructions of the
manufacturer.
Connect it to the terminals [57] and [58] of the outdoor
!
station with a two-core cable (polarity-independent)
according to the connection diagram (see Fig. I).
Connecting optional powered loudspeaker
Connect an optional powered loudspeaker [48] (not
!
included in the package contents), e.g. a PC speaker,
to the terminals [53] and [54] of the indoor station with
a two-core cable according to the connection diagram
(see Fig. I). Pay attention to the polarity for the
connection.
Connecting the mains adapter to the indoor station
Connect the low-voltage connector [13] to the
!
connection [50].

Finishing the wall mounting

Finishing the outdoor station mounting
For cable routing along the wall: Guide all connected
!
cables through the cable opening [25].
Slide the outdoor station [1] at an angle upwards into
!
the wall bracket and push it into place.
Fix the outdoor station to the wall bracket through the
!
two holes [30] with two of the fixing screws [4].
Finishing the indoor station mounting
Screwing to the wall
For cable routing through the wall: Place the
!
connection cable [14] into the cable channel [51].
For cable routing along the wall: Place the mains
!
adapter cable into the cable channel [51].
Slide the indoor station [2] at an angle upwards into
!
the wall bracket and push it into place.
Fix the indoor station to the wall bracket through the
!
hole [47] with one fixing screw [4].
Hanging on the wall
Hang the indoor station [2] on the two protruding
!
screw heads in the wall using the keyhole slots [49].

First use

Plug the mains adapter [12] into a mains power
!
socket. The operating status LED [35] lights green
and the nameplate cover [20] is illuminated from the
back.
Remove the protective film from the monitor [33].
!
The video door entry system is now ready for operation.

Operation

A visitor presses the doorbell button [21] of the outdoor
station. A chime sounds from the indoor station. The
camera image is displayed on the monitor [33] and the
operating status LED [35] lights red. It can now be heard
on the indoor station what is said at the outdoor station.
If the visitor presses the doorbell button again, the chime
GB / IE - 7