Yamaha YSP-600 Owner's Manual page 98

Continued from the front
3
Carry out the AUTO SETUP (IntelliBeam)
Carry out the AUTO SETUP to adjust the settings that best match your listening
environment.
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment.
during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
1 Assemble the cardboard microphone stand.
Place the IntelliBeam microphone on top of the cardboard microphone stand as shown below.
1 2 3
2 Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack
on the front panel.
IntelliBeam microphone (supplied)
INTELLIBEAM MIC INPUT VOLUME STANDBY/ON
INTELLIBEAM MIC
Cardboard microphone stand (supplied)
3 Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
be when you are seated.
IntelliBeam
Upper bound
microphone
position of the
microphone
Center height of
this unit
Within 1 m (3.3 ft)
Within 1 m (3.3 ft) Center line
Cardboard
IntelliBeam
Listening
Cardboard
microphone stand
microphone
position
microphone
More than 1.8 m (6.0 ft)
Lower bound position
stand
of the microphone
Press STANDBY/ON on the remote control.
4
The power of this unit turns on.
Before operations, insert batteries into the remote
control (see page 27 in the Owner's Manual).
If necessary, adjust the volume level of this unit. STANDBY/ON POWER POWER
AV TV
5 Turn on the power of your TV.
Select the appropriate video input
6
on your TV.
If the OSD video pin cable is connected to the video input 1 on
It is normal for loud test tones to be output
the TV as shown in the connection example, switch the video
input to "1".
7 Set the operation mode selector to
4
YSP.
This unit switches to the YSP operation mode.
CH LEVEL
TEST
8 Press and hold AUTO SETUP for
more than 2 seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video pin
cable (see the connection example on the front page).
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM ST+3BEAM 3BEAM
1 2 3
9 Check the following points.
Place the IntelliBeam microphone on the
extended center line of this unit and 1.8 m (6.0 ft) About the IntelliBeam microphone
or more away from it. Also, make sure place the
• Is the microphone placed on an imaginary center line drawn
IntelliBeam microphone within 1 m (3.3 ft) upper
from this unit?
or lower from the center height of this unit.
• Is the microphone placed within 1 m (3.3 ft) upper or lower
from the center height of this unit?
• Is the microphone placed more than 1.8 m (6.0 ft) from the
front of this unit?
About the room environment
• Is your listening room kept as quiet as possible?
10 Prepare to leave the room.
The best setting may not be done if you are in the room.
If you have connected the subwoofer, set the
Prepare to leave the room in 10 seconds after pressing ENTER
volume and crossover/high cut frequency. Refer
in step 11.
to the notes on page 33 in the Owner's Manual.
Hint
Subwoofer
• When leaving the room, bring this guide with you.
VOLUME CROSSOVER/
HIGH CUT • Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes
• To cancel the AUTO SETUP procedure after it is started,
press RETURN.
MIN MAX MIN MAX
11 Press ENTER to start the AUTO
SETUP procedure, and then leave
the room within 10 seconds.
The following screen appears on the TV. Leave the room within
10 seconds before the AUTO SETUP procedure starts.
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
The setup screen automatically changes during the AUTO
SETUP procedure.
When the AUTO SETUP procedure is completed, the following
screen appears on the TV.
MENU
SHOW RESULT
TV/AV
ENTER
MEASUREMENT COMPLETE
YSP
BEAM MODE :5 BEAM
RETURN
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save set-up
[RETURN]:Do not save set-up
If "ENVIRONMENT CHECK (FAILED)" is displayed, see page
37 in the Owner's Manual and then run the procedure again.
Hint
• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears
on the screen. In this case, see "Error messages for AUTO
SETUP" on page 38 in the Owner's Manual and then follow
AUTO SETUP
PREPARATION & CHECK the instructions. To start the AUTO SETUP procedure once
Please connect the MIC.
Please place the MIC at least
again, press RETURN.
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
Press ENTER.
12
The following screen appears on the TV for 2 seconds and then
the menu screen disappears from the TV.
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
13 Disconnect the IntelliBeam
microphone.
The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.
about 3 minutes.
INTELLIBEAM MIC
4
Enjoying surround sound
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player/recorder, refer to the owner's manual supplied with each component.
AUTO SETUP START
Enjoying DVDs in surround sound
Will begin in 10sec
Please leave the room
**--------
[RETURN]:Cancel
1 Select the DVD video input on
your TV.
Set the operation mode selector to
2
YSP.
This unit switches to the YSP operation mode.
TV/AV
ENTER
YSP
TEST RETURN
3 1) Press DVD on the remote
control of this unit.
This unit switches to the DVD playback mode.
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
2) Play back the supplied demonstration
DVD on the DVD player/recorder.
4 Check the multi-channel digital signal being output at this unit.
AUTO SETUP COMPLETE
The MULTI indicator (see page 8 in the Owner's Manual) is lit in the front panel display.
Please remove the MIC from
the YSP and the listening
from your TV speakers, mute the volume on your TV.
position.
the Owner's Manual.
Press VOLUME +/– on the remote control to adjust the
5
volume level of this unit.
Press one of the beam mode buttons on the remote control to
6
select the desired beam mode.
Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see pages 45 to 47 and 51 to 53 in the Owner's Manual.
To fine-tune the listening environment parameters manually or make advanced settings for speaker positions, sound
beams, etc., see "MANUAL SETUP" on page 58 in the Owner's Manual.
Enjoying TV in surround sound
1 Select the TV channel using the
remote control supplied with your TV.
Mute the volume on the TV.
Set the operation mode selector to
2
YSP.
This unit switches to the YSP operation mode.
TV/AV
ENTER
YSP
TEST RETURN
3 Press TV on the remote control of
this unit.
This unit switches to the TV playback mode.
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM ST+3BEAM 3BEAM
1 2 3
MULTI indicator
If the sound is output
For details about digital audio input signals, see page 43 in
VOLUME CH TV VOL
MUTE TV INPUT TV MUTE
5BEAM ST+3BEAM 3BEAM
1 2 3
STEREO MY BEAM MY SUR.
4 5 6