Operating Instructions LCD Projector Commercial Use PT-LB80NTU Model No. PT-LB80U PT-LB75NTU PT-LB75U Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0244 NGLISH...
We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.
To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to computer and/or peripheral devices. Any changes or modifications not expressly approved by Panasonic Corp. of North America could void the user's authority to operate this device.
Contents Quick steps Important Information Important Safety Notice ..........2 1. Set up your projector Precautions with regard to safety......6 See “Setting up” on page 15. WARNINGS ..............6 CAUTIONS................ 7 Cautions when transporting ..........8 Cautions when installing ........... 9 Cautions on use ..............
Page 5
Contents Settings Appendix Menu Navigation ............27 Technical Information ..........44 Navigating through the MENU ........27 List of compatible signals ..........44 Main menu and Sub-menu..........28 Serial terminal..............45 PICTURE menu............30 Computer connection guidance........46 Screen size and throw distance for 16:9 aspect ratio..47 PICTURE MODE ............
Precautions with regard to safety WARNINGS If you notice smoke, strange smells or noise coming Insert the power plug securely into the wall outlet. from the projector, disconnect the power plug from If the plug is not inserted correctly, electric shocks or the wall outlet.
Precautions with regard to safety Do not place your skin into the light beam while the Do not place your hands or other objects close to the projector is being used. air outlet port. Strong light is emitted from the projector’s lens. If you Heated air comes out of the air outlet port.
Precautions with regard to safety Do not short-circuit, heat or disassemble the Do not put your weight on this projector. batteries or place them into water or fire. You could fall or the projector could break, and injury Failure to observe this may cause the batteries to may result.
Precautions with regard to safety Cautions when installing Avoid setting up in places which are subject to If installing the projector to the ceiling, ask a vibration or shocks. qualified technician to carry out all installation work. The internal parts can be damaged, which may cause You will need to purchase the separate installation kit.
Precautions with regard to safety Accessories Make sure the following accessories are provided with your projector. Remote control for Remote control for AA batteries for Remote Power cord secure lock PT-LB80NTU / PT-LB80U / PT-LB75U control (x2) (x1) TMXX051 PT-LB75NTU (x1) (x1) N2QAYB000260 N2QAYB000262...
Read this first Minimum required setting screen When you start the projection for the first time or after the projector is initialised, the minimum required setting screen for projection will be displayed. LANGUAGE INSTALLATION Press I H buttons of the remote control or control Select the required language setting.
About Your Projector Projector body Top and front view Zoom-Focus ring cover Cover the zoom and focus rings to protect from dust. Zoom ring (page 22) Focus ring (page 22) Air intake port Lens cover page 40 Remote control signal receptor (page 23) Indicators POWER LOCK indicator (page 21)
Page 13
About Your Projector Back and bottom view Security lock Attach the commercial shackle lock, Lamp unit compartment Burglar hook port manufactured by Kensington, to Attach a commercial burglar (page 41) protect your projector. Compatible prevention cable. with the Kensington MicroSaver Security System.
About Your Projector Remote control POWER button Detect the input signal and the Switch between stand-by setting of POSITION, DOT mode and projection mode. CLOCK and CLOCK PHASE (page 19/page 20) in POSITION menu will be adjusted automatically for The PAGE buttons are only COMPUTER signals.
Setting up Projection method You can use the projector with any of the following 4 projection methods. To set the desired method in the projector, See “INSTALLATION” on page 35. Setting on a desk/floor and Setting on a desk/floor and projecting from front projecting from rear INSTALLATION: FRONT/DESK...
Connections Before connection to the projector Read and follow the operating and connecting instructions of each peripheral device. The peripheral devices must be turned off. Prepare the connecting cables that match with the projector and peripheral device terminals. If the input signal is affected by signal jitter, the projected image may have poor image quality and timebase correction is effective.
Switching the projector on/off Power cord Connecting Disconnecting 1. Make sure the shape of the power plug and the 1. Unplug the power cord from the wall outlet. AC IN terminal on the back of the projector match, 2. Depress the latch and slide the cover off. then push the plug all the way in.
Switching the projector on/off Switching on the projector Before switching on the projector, make sure the power cord and all the other devices are connected correctly. See “Connections” on page 17 and “Power cord” on page 18. By control panel operation By remote control operation Make sure CONTROL PANEL in OPTION menu is 1.
Switching the projector on/off Switching off the projector By control panel operation By remote control operation Make sure the CONTROL PANEL setting in 1. Press the POWER button. OPTION menu is set to VALID. The confirmation screen will be displayed. Without any operation for 10 seconds or press any 1.
Switching the projector on/off POWER and POWER LOCK indicators The POWER indicator informs you the status of the power and the POWER LOCK indicator shows the status of the RELEASE button. POWER LOCK indicator POWER indicator POWER LOCK indicator status Indicator status Status No power is supplied.
Projecting an image Selecting the input signal 1. Switch on the connected devices. NOTE: Press the play button of the required device. 2. Detect the input signal automatically. • If the SIGNAL SEARCH in OPTION menu is deactivated, select the required input method by 3.
Remote control operation Operating range You can operate the projector with the remote control within the remote range 15 m (49'2"), approximately ± 30° vertically and horizontally Facing to the projector Make sure the remote control emitter is facing to the remote control signal receptor of the projector when pressing the buttons to operate.
Remote control operation Switching the input signal Pressing the WIRELESS button You can switch the input method manually by pressing the COMPUTER, WIRELESS The WIRELESS button is only for PT-LB80NTU/ (PT-LB80NTU/PT-LB75NTU only) and PT-LB75NTU. VIDEO buttons. Press the required button See CD-ROM contents for more detailed information.
Remote control operation Projecting an image in INDEX-WINDOW mode Changing the image size You can project an image split in 2 windows as an INDEX-WINDOW. One is frozen and Press F G to capture a new image and change stored in memory, and displayed on the the size in 3ways.
Remote control operation Enlarging the centered area Shifting the center point You can enlarge the projected image down to a centered area for emphasizing within Press F G I H to shift the center point. the range of 1x to 2x. Enlarging the image 1.
Menu Navigation The menu system allows you to access functions which do not have their own dedicated buttons on the remote control. The menu options are structured and categorised. You can navigate through the menu with F G H I buttons.
Menu Navigation Main menu and Sub-menu The main menu has 6 options. Select the required menu item and press ENTER to display the sub-menu. Underlined items are factory default settings. NOTE: • Some default settings vary by the selected input signal. •...
Page 29
Menu Navigation DETAILED SETUP page 36 OPTION OSD DESIGN TYPE1 TYPE2 INPUT GUIDE page 34 TYPE3 DETAILED SIMPLE SXGA MODE SXGA SXGA+ STARTUP LOGO page 34 BLACKBOARD USER BACK COLOR COMPUTER2 SELECT page 34 BLUE BLACK INPUT OUTPUT VOLUME (Default: 20) RGB/YP page 34 AUDIO BALANCE (Default: 0)
PICTURE menu COLOR Remote control Control panel You can adjust the color saturation of the projected image. (Available with signals of VIDEO/S-VIDEO/ MENU RETURN only) Lighter Darker See “Navigating through the MENU” on page 27. See “Main menu and Sub-menu” on page 28. PICTURE MODE TINT Depending on the projection environment, you can use...
PICTURE menu STILL MODE DETAILED SETUP You can reduce the vertical flicker when projecting a still image. You can perform more detailed image adjustment Active manually. OFF: Deactive For S-VIDEO/VIDEO signals NOTE: TV-SYSTEM • Set to OFF when projecting a moving image. When the video signal is changed, the setting NOISE REDUCTION switches automatically.
POSITION menu DOT CLOCK Remote control Control panel If you have interference patterns of the projected image, which is sometimes referred to as moire or noise, you MENU RETURN can minimize it by pressing I H to adjust the clock frequency.
POSITION menu 16:9 THROUGH The squeezed signal will be projected in 16:9 ratio. The image will be projected without any size adjustment. AUTO S4:3 The signal which contains an identifying signal will The input signal will be sized down 75 % and be detected and automatically project the image in projected.
OPTION menu 1. Select USER and press the ENTER button. Remote control Control panel 2. Select the required line to enter or edit the original text, and press the ENTER button. 3. Use F G I H to specify the location of the required character and press the ENTER button.
OPTION menu LAMP POWER AUTO SETUP You can adjust the power of the lamp to save electricity, You can turn off the automatic AUTO SETUP prolong the lamp life and reduce the noise. adjustment system. STANDARD When higher luminance is required AUTO When the projector detect a ECO-MODE...
OPTION menu SXGA MODE CLOSED CAPTION SETTING When an SXGA signal image is cropped, you can If the input signal contains closed captions, you can turn switch the setting between SXGA and the larger on the feature and switch the channels. setting, SXGA+.
SECURITY menu PASSWORD CHANGE Remote control Control panel You can change the password operation to your original. 1. Press a series of button operation up to 8 as a MENU RETURN password by using F G I and H buttons. 2.
WIRELESS menu Items in WIRELESS menu Remote control Control panel In WIRELESS menu, the following items are available. NETWORK MENU RETURN NAME CHANGE INPUT PASSWORD PASSWORD CHANGE NETWORK STANDBY WEB CONTROL See “Navigating through the MENU” on page 27. LIVE MODE CUT IN See “Main menu and Sub-menu”...
LAMP and TEMP Indicators Managing the indicated problems If a problem should occur with the projector, the LAMP and/or TEMP indicators will inform you. Manage the indicated problems as follow. 1. Confirm the status of all indicators and projector, and switch off the projector in proper way.
Care and Replacement Cleaning the projector Before cleaning the projector Switch off the projector and disconnect the power plug from the wall outlet. Unplug all the cables from the projector. Cleaning the outer surface of the projector Wipe off dirt and dust gently with a soft cloth. If it is difficult to remove the dirt, soak a cloth with water, wring the cloth well and then wipe the projector.
Care and Replacement Replacing the Lamp unit The lamp unit, ET-LAB80 is consumable and you must replace it regularly. It is recommended that a qualified technician carry the lamp unit replacement and consult with an Authorized Service Center. When to replace the Lamp unit When the lamp is consumed, the brightness may decrease over time.
Care and Replacement Replacement procedure Removing and replacing the lamp unit 1. Use a Phillips-head screwdriver to loosen the 2 3. Pull the used lamp unit gently from the projector. lamp unit cover fixing screws on the back of the Grip the handle and keep the lamp unit paralleled when you remove the lamp.
Troubleshooting Should any problem persist, contact your dealer. Reference Problem Cause page The power cord may not be connected securely. No electric supply at the wall outlet. TEMP indicator is lit or flashes. Power does not turn on. LAMP indicator is lit or flashes. The lamp unit cover has not been securely installed.
Technical Information List of compatible signals Scanning Display Dot clock Picture frequency resolution Mode frequency Terminals quality (MHz) (dots) H (kHz) V (Hz) NTSC/NTSC 4.43/ 720 x 480i 15.7 59.9 PAL-M/PAL60 VIDEO/S-VIDEO PAL/PAL-N/SECAM 720 x 576i 15.6 50.0 525i (480i) 720 x 480i 15.7 59.9...
Technical Information Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connecter. Connection D-sub 9 pin (male) Serial terminal (female) Computer...
INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. Manufacturer Key command Manufacturer Key command Manufacturer Key command TOSHIBA SONY Panasonic SHARP Apple EPSON FUJITSU Other DELL NOTE: • The computer connection guidance will disappear after 5 minutes.
Technical Information Specifications Power supply AC 100 - 240 V 50 Hz/60 Hz 300 W Power consumption During standby (when fan is stopped): 4 W Amps 3.5 A - 1.2 A Panel size (diagonal) 0.63 type (16.00 mm) Aspect ratio 4 : 3 LCD panel Display method...
Page 49
Technical Information Single - line, Mini DIN 4p S-VIDEO IN Ω Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Single - line, RCA pin jack VIDEO IN Ω 1.0 V [p-p], 75 Single - line, D - sub HD 15-pin (female) RGB input/output Ω...
Technical Information Dimensions (14 - 15/32") Unit: mm 3 - 15/32" 88.6 103.6 4 - 1/16" 194.4 7 - 5/8" Trademark acknowledgements VGA and XGA are trademarks of International Business Machines Corporation. S-VGA is a registered trademark of the Video Electronics Standards Association. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Index ........14 Remote control button ...........50 Dimensions ............13 AC IN ..........18 Direct power off ..........10 Accessories DIRECT POWER ON ..........13 Air exhaust port ...........18 Function ............35 Air filter Menu ..........40 ..........32 Cleaning DOT CLOCK ..........13 Compartment ..........
Page 52
Index ........... 34 STARTUP LOGO ..........31 STILL MODE Navigation buttons ............ 28 Sub-menu ........12 Control panel button ..........13 S-VIDEO IN ........14 Remote control button ..........36 SXGA MODE ........31 NOISE REDUCTION ........44 Technical Information ..........
Nous espérons qu'elle vous aidera à optimiser l'utilisation de votre nouveau produit et que vous serez satisfait de votre projecteur LCD Panasonic. Le numéro de série de votre produit se trouve sous le projecteur. Veuillez le noter dans l'espace ci-dessous prévu à cet effet et conserver cette notice en cas de maintenance requise.
Page 54
PT-LB80NTU / PT-LB75NTU/PT-LB80U/PT-LB75U Désignation commerciale:Panasonic Fabricant responsable: Panasonic Corporation of North America Adresse: One Panasonic Way, Secaucus, New Jersey 07094 Téléphone: (888) 411 - 1996 Email: projectorsupport@us.panasonic.com Cet appareil est conforme à la partie 15 des règles de la FCC (Federal Communicaitions Commission U.S.A.) ce qui signifie: (1) que l'appareil ne produit pas d'interférences nuisibles, et (2) que l'appareil est capable de...
Précautions de sécurité AVERTISSEMENTS Si l'on remarque une émission de fumée, d'odeurs Ne pas manipuler le cordon d'alimentation avec les suspectes ou de bruits provenant du projecteur, mains mouillées. débrancher la fiche du cordon d'alimentation de la Cela peut entraîner des chocs électriques. prise de courant.
Précautions de sécurité Veiller à ce que les bornes + et – des piles n'entrent Ne pas placer les mains ou autres objets près de pas en contact avec des objets métalliques tels que l'orifice de sortie d'air. colliers ou épingles à cheveux. De l'air chaud sort par l'orifice de sortie d'air.
Précautions de sécurité Ne pas court-circuiter, chauffer ou démonter les Ne pas peser de tout son poids sur ce projecteur. piles, et ne pas les mettre dans l'eau ou dans le feu. On risque de tomber ou de casser l'appareil, ce qui Si l'on utilise des piles différentes ou si elles ont peut causer des blessures.
Précautions de sécurité Si le projecteur est installé au plafond, demander à Ne pas installer le projecteur près de lignes un technicien qualifié de faire tous les travaux d'alimentation électrique à haute tension ou de mo- d'installation. teurs. Il faut acheter le kit d'installation séparé (numéro de Le projecteur peut être soumis à...
Remplacement de l'unité de la lampe Avant de remplacer le l'Unité de la lampe Eteindre l'ALIMENTATION PRINCIPALE puis débrancher le cordon principal de la prise du secteur. Attendez au moins 1 heure que la lampe et les composants contigus soient suffisamment froids. Préparer un tournevis cruciforme.
Remplacement de l'unité de la lampe Procédure de remplacement Retirer et remplacer la lampe 1. Dévisser à l'aide d'un tournevis cruciforme les 5. Remettre la nouvelle Unité de la lampe à son 2 vis de fixation du Couvercle de la lampe à emplacement.
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Projectors Panasonic Projector Systems Company Unit of Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ 07094 (201) 392 - 6591 Technical Support: (888) 411 - 1996 FAX: (201) 348 - 7523 E-Mail: projectorsupport@us.panasonic.com...