Table of Contents
Advertisement
Quick Links
User Guide
PLEASE READ & SAVE THESE ORIGINAL INSTRUCTIONS
Image Spot™
This guide applies to the following Rosco Image Spot models:
Image Spot IP40
Black (296000040401)
White (296000040402)
Silver (296000040403)
Image Spot IP65
Black (296000040651)
White (296000040652)
Silver (296000040653)
Image Spot IP65 w/DMX Cable
Black (296000041651)
White (296000041652)
Silver (296000041653)
Advertisement
Table of Contents
Related Manuals for Rosco Image Spot IP65
Summary of Contents for Rosco Image Spot IP65
- Page 1 User Guide PLEASE READ & SAVE THESE ORIGINAL INSTRUCTIONS Image Spot™ This guide applies to the following Rosco Image Spot models: Image Spot IP40 Black (296000040401) White (296000040402) Silver (296000040403) Image Spot IP65 Black (296000040651) White (296000040652) Silver (296000040653) Image Spot IP65 w/DMX Cable...
-
Page 3: Table Of Contents
Warranty ..................................20 Information and specifications in this document are subject to change without notice. Rosco assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. Image Spot™ User Guide Copyright ©2017 by Rosco... -
Page 4: Introduction
InTRoDUCTIon Congratulations on your purchase of a Rosco Image Spot projector. Designed to provide crystal-clear imaging and spot illumination, the Image Spot is quick and easy to set up with convenient on-board dimming or remote DMX controls. Image Spot is available in durable indoor IP40 and outdoor IP65 versions. To ensure efficient and safe operation, please take a few moments to read this manual completely. - Page 5 PReVenTInG eleCTRIC sHoCK This machine uses mains electrical power at 90-253VAC inclusive. When directly contacted, such voltages are hazardous to human life. Follow all local electrical codes and take precautions when using this product. This product is designed to operate from three-wire power systems, where one of the wires is a safety ground. DO NOT disconnect the safety ground, or use extension cords or adapter plugs to connect this machine to a two- wire system.
- Page 6 Rosco Image Spot is not certified for use in hazardous locations. Rosco Image Spot is designed for operation within the range of 14° to 104°F (-10° to +40°C). Ensure Rosco Image Spot is stored within the range of -4° to 140°F (-20° to +60°C).
-
Page 7: Unpacking
UnPaCKInG Carefully remove the unit from the box. Do not attempt to operate Rosco Image Spot projector if there are any signs of physical damage. In case of damage, contact your local Rosco dealer. Your Rosco Image Spot projector requires that an Image Spot focusing lens tube (purchased separately) be inserted into the opening on the front of the unit prior to operation. -
Page 8: Installing Lens Tube
InsTallInG lens TUbe IP40 Units: Insert the small diameter end of the lens tube into the opening on the front of the projector. IP65 Units: Slip the 2 provided O-rings onto the grooves on the back end of the lens tube. Gently insert the end of the lens tube with O-rings into the opening on the front of the projector. -
Page 9: Wiring
WIRInG Your Rosco Image Spot projector will arrive with an unterminated power cord attached to the unit. Wiring to an appropriate connector (not included with Image Spot purchase) or to line voltage should be performed by a qualified electrician and is the responsibility of the installer or end user. The power cord wiring code is as follows:... -
Page 10: Mounting
MoUnTInG The Image Spot projector can be installed in the desired location via the center hole in the yoke. Adjust pan as required. Adjust and fix the tilt of the projector via (1) the knurled thumb knob or (2) optional hex screw (supplied with Image Spot) on the side of the yoke. -
Page 11: Gobo Projection
A flat tipped screw driver can be used for additional torque to tighten the thumb screws. For optimum image quality, use Rosco Image Spot gobos, which feature custom bezels that fit securely inside the Image Spot gobo cassette. -
Page 12: Focusing
Due to the ultra-clear optics of the Image Spot projector, it is advised to keep the optic path clean of dust and debris. Use a non-abrasive micro-fiber cloth with Rosco Lens Cleaner to clean the Image Spot lenses and any glass gobos or Permacolor dichroic glass filters you may have installed. -
Page 13: Dmx Operation
DMX Programming Cable (sold separately) is needed, as well as the free Image Spot Addressing Software that can be downloaded at www.rosco.com/ImageSpot. To set the DMX address on the Image Spot IP40 unit, you will need the USB to RJ45 Cable accessory, sold separately. - Page 14 DMX oPeRaTIon The Image Spot IP65 units can be ordered with a factory-installed 2m length of DMX cable that features a water-proof gland. To set the fixture’s DMX address, you will need the Image Spot USB to RS485 Programming Cable accessory (sold separately). Plug the USB connector into the computer running the Image Spot Addressing Software and wire the cable’s multi-pin terminal block to the bare-ends of the fixture’s DMX cable using the following terminal assignment: Terminal 1 Data + (Blue)
-
Page 15: Diffusion Filters
DIffUsIon fIlTeRs An optional Image Spot OPTI-FLECS™ Filter Pack is available and features three pre-cut, 43mm round diffusion filters that soften Image Spot’s beam for spot lighting purposes. The OPTI-FLECS Filter Pack includes: • Retaining Ring • Soft Diffusion – 43mm dia. • Smoothing Frost – 43mm dia. • Double Powder Frost – 43mm dia. To install OPTI-FLECS filters into the Image Spot: insert the 43mm disc into the front end of the lens tube and then secure the filter into place using the Retaining Ring. -
Page 16: Dichroic Color Filters
DICHRoIC ColoR fIlTeRs Rosco Permacolor dichroic filters are available to provide fully customizable, long-term color options for your Image Spot. For optimal performance and installation, specify Image Spot Permacolor Filters that feature custom bezels to fit securely inside the Image Spot gobo cassette. -
Page 17: Accessories
aCCessoRIes Item number Description 296000010019 Image Spot Narrow Angle Lens Optic / 19º 296000010025 Image Spot Medium Angle Lens Optic / 25º 296000010030 Image Spot Wide Angle Lens Optic / 30º 296000010013 Image Spot OPTI-FLECS Filter Pack with Retaining Ring 296000010012 Image Spot Safety Cable, 3-ft (1m) 296000010011... -
Page 18: Ordering Gobos & Permacolor Filters
Gobos & PeRMaColoR fIlTeRs Gobos and Permacolor Dichroic Filters for the Image Spot projector can be easily ordered through any Rosco dealer. Visit www.rosco.com to locate the dealer nearest you and provide them with the information below. standard Gobos... -
Page 19: Technical Specifications
3,000 lumen output Environments LM-79-08 : 50,000 hours @ 45C Environmental: Disposal of Old Electrical & Gobo specifications Rosco Image Spot Gobo Electronic Equipment with custom carrier This symbol on the product or on Working environment its packaging indicates that this Ambient Temp.:... -
Page 20: Warranty
This warranty does not cover damage to the Rosco Product caused by parts not manufactured, distributed or certified by Rosco. Rosco is not obligated to provide warranty service should the Product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as flood, fire and lightning, improper electrical current or unauthorized service repairs other than those by a Rosco Authorized Servicer. - Page 21 OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY AND UNLESS EXCLUSIONS ARE SPECIFICALLY FORBIDDEN BY STATE LAW, NEITHER ROSCO NOR ITS AFFILIATES WILL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURY TO PERSONS OR PROPERTY, RESULTING FROM THE USE OR INABILITY TO USE THE ROSCO PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY.
- Page 22 5007481...
Need help?
Do you have a question about the Image Spot IP65 and is the answer not in the manual?
Questions and answers