Dolby Digital Mode And Dts Surround - Denon AVR-786 Operating Instructions Manual

ENGLISH
Basic Operation
INPUT MODE STANDARD
SURROUND MODE
FUNCTION SURROUND PARAMETER

Dolby Digital mode and DTS surround

(only with digital input)
1
Select an input source set to digital (COAXIAL/
OPTICAL) ( page 39).
Example: DVD
(Main unit)
2
INPUT MODE
Press the
mode to "AUTO" or "DTS".
3
STANDARD
Press the
STANDARD (Dolby/DTS Surround) mode.
When performing this operation from the main unit's panel,
press the SURROUND MODE button, then turn the SELECT
knob and select Dolby Pro Logic
4
Play a program source with the
symbol.
• The Dolby Digital indicator lights
when playing Dolby Digital
sources.
• The DTS indicator lights when
playing DTS sources.
Operate the SURROUND BACK button
to switch Surround Back CH ON/OFF.
• The SURROUND BACK indicator
lights when the SURROUND BACK
button is on.
STANDARD
STATUS
SELECT
ON SCREEN
INPUT MODE
5
Press the
• The surround parameter menu is displayed.
(Remote control unit)
button to set the input
6
Press the
press the
button to select the
various parameters.
7
Turn the
F F
or
II x or DTS NEO:6.
8
Press the
or
parameter mode.
Lights
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
Lights
Lights
FUNCTION
SURROUND
ENTER
PARAMETER
CURSOR
SURROUND
BACK
SURROUND PARAMETER
button.
SURROUND PARAMETER
button, and
CURSOR D D H H
or button to select the
SELECT
knob, and press the
G G
button to adjust the parameter settings.
ENTER
button to finish the surround
23
ENGLISH
2 Surround parameters e
CINEMA EQ. (Cinema Equalizer):
The Cinema EQ function gently decreases the level of the
extreme high frequencies, compensating for overly-bright
sounding motion picture soundtracks. Select this function if the
sound from the front speakers is too bright.
This function only works in the Dolby Pro Logic
Digital, DTS Surround and DTS NEO:6 modes. (The same
contents are set for all operating modes.)
D.COMP. (Dynamic Range Compression):
Motion picture soundtracks have tremendous dynamic range
(the contrast between very soft and very loud sounds). For
listening late at night, or whenever the maximum sound level is
lower than usual, the Dynamic Range Compression allows you
to hear all of the sounds in the soundtrack (but with reduced
dynamic range). (This only works when playing program
sources recorded in Dolby Digital or DTS). Select one of the
four parameters ("OFF", "LOW", "MID" (middle) or "HI"
(high)). Set to OFF for normal listening.
LFE (Low Frequency Effect):
This sets the level of the LFE (Low Frequency Effect) sounds
included in the source when playing program sources recorded
in Dolby Digital or DTS.
If the sound produced from the subwoofer sounds distorted
due to the LFE signals when playing Dolby Digital or DTS
sources when the peak limiter is turned off with the subwoofer
peak limit level setting (system setup menu), adjust the level as
necessary.
Program source and adjustment range:
1. Dolby Digital: –10 dB to 0 dB
2. DTS Surround: –10 dB to 0 dB
When DTS encoded movie software is played, it is
recommended that the LFE LEVEL be set to 0 dB for
CURSOR
correct DTS playback.
When DTS encoded music software is played, it is
recommended that the LFE LEVEL be set to –10 dB for
correct DTS playback.
TONE:
This enables the tone control. This can be set individually for
the separate surround modes other than DIRECT mode.
Basic Operation
II x, Dolby