Related Manuals for Rockford Fosgate punch 160
Summarization of Contents
SPECIFICATIONS - Power Ratings
Dynamic Power Rating
Details power output under dynamic conditions.
Continuous Power Rating
Details power output under continuous conditions.
SPECIFICATIONS - Component Details
Dimensions
Physical dimensions of the amplifier unit.
Damping Factor
Damping factor specification at a 4-ohm load.
Slew Rate
Amplifier's slew rate specification.
IM Distortion
Intermodulation distortion measurement.
Input Sensitivity
Amplifier's input sensitivity and compatibility.
Protection
Details the amplifier's protection circuitry.
Fuse Rating
Recommended fuse rating and type for amplifier connection.
Equalization
Specification for the bass equalization feature.
Input Impedance
Amplifier's input impedance specification.
INTRODUCTION
Punch Amplifier Accessory Pack
Lists accessories included with the Punch amplifiers.
DESIGN FEATURES
Punch 120 / Punch 160 Connections
Illustrates connection points for Punch 120 and 160 models.
MOUNTING LOCATION
Trunk Mounting
Guidance on mounting the amplifier in the trunk for optimal cooling.
Passenger Compartment Mounting
Guidance on mounting in the passenger compartment with ventilation considerations.
Engine Compartment Mounting
Warning against mounting the amplifier in the engine compartment.
OPERATION
Using Passive Crossovers
Explanation of passive crossover networks and their usage.
INSTALLATION
Using RCA and High Level Inputs
Illustrates signal input options using RCA or High Level connections.
INSTALLATION
Punch 120/160 Power & Bridged/Mono Mode
Shows power connections and bridged/mono setup for Punch 120/160.
INSTALLATION
Punch 120/160 2-Channel and 3-Channel Modes
Diagrams for 2-channel and 3-channel modes for Punch 120/160.
INSTALLATION
Punch 250/360/500 Power & Bridged/Mono Mode
Details power connections and bridged/mono mode for Punch 250/360/500.
INSTALLATION
Punch 250/360/500 2-Channel and 3-Channel Modes
Diagrams for 2-channel and 3-channel modes for Punch 250/360/500.
INSTALLATION
Punch 800 Power & Bridged/Mono Mode
Details power connections and bridged/mono mode for the Punch 800 model.
INSTALLATION
Punch 800 2-Channel and 3-Channel Modes
Diagrams for 2-channel and 3-channel modes for the Punch 800.
OPERATION
Crossover Operation
Explains how to operate the internal crossover for different frequency settings.
Punch Bass
Details the operation of the Punch Bass feature for bass enhancement.
SYSTEM DIAGRAMS
2-Way System
Illustrates a typical 2-way speaker system wiring diagram.
SYSTEM DIAGRAMS
3-Way System Using Single Voice Coil Woofers
Illustrates a 3-way system with single voice coil woofers.
SYSTEM DIAGRAMS
3-Way System Using Dual Voice Coil Woofers
Illustrates a 3-way system with dual voice coil woofers.
TROUBLESHOOTING
Amplifier Power & Sound Issues
Troubleshooting steps for power and sound issues.
Distorted Output & Turn-on Noise
Troubleshooting steps for distorted output and turn-on noise.
TROUBLESHOOTING
Turn-on Pop & Engine Noise
Troubleshooting for turn-on pop and engine noise interference.
Engine Noise with High-Level Inputs
Troubleshooting engine noise specifically with high-level inputs.
DYNAMIC POWER MEASUREMENTS
About Dynamic Power Measurements
Explains the methodology behind dynamic power measurements.
Music & Loudspeaker Measurements
Discusses how music and loudspeaker characteristics affect measurements.
LIMITED WARRANTY INFORMATION
Warranty Duration & Coverage
Specifies warranty length, what is covered, and who is covered.
Warranty Exclusions & Limitations
Lists what is not covered and limits on implied warranties.
How to Obtain Service
Provides instructions on how to get service and obtain an RA number.
Need help?
Do you have a question about the punch 160 and is the answer not in the manual?
Questions and answers