Lexicon PCM 80 - REV 1 DUAL FX User Manual page 71

PCM 80 Dual FX User Guide
3-16
0.9 Bounce+ Eko2
A dual mono in/stereo out program, that provides a tap echo on the left input and an
absolute-time echo on the right. The left input feeds a sixteenth-note echo that bounces
between left and right as it repeats. The right input feeds a separate mono echo. ADJUST
controls the mono echo delay time. The Soft Row contains additional controls for both
effects. Use this program to process two mono sources independently, or to process one
mono source with two independent effects. T
1.0 Bounce+ Eko3
A dual mono in/stereo out program.The left and right input feed two independent delay
lines. The left echo bounces between left and right. The right echo is set for the same
rhythm as the left, but repeats in the center. ADJUST allows you to add an additional offset
to the right input's echo. The Soft Row contains additional controls for both effects. T
1.1 Bounce+ Eko4
A dual mono in/stereo out program.The left and right input feed two independent delay
lines. The left echo bounces between left and right with an eighth-note rhythm. The right
input echo is also rhythmic. ADJUST controls the number of echoes per beat. The Soft
Row contains additional controls for both effects. T
1.2 Bounce+ Eko5
A dual mono in/stereo out program.The left and right input feed two independent delay
lines. The left input echoes bounce between left and right. The right input echoes repeat
in the center. Both delay lines are set for the same rhythm. ADJUST sets the relative
amount of feedback for both echo effects. If you feed the same signal to both inputs, you'll
notice that the first few repeats are in the center of the mix, then they begin to spread to
the sides. The Soft Row contains additional controls for both effects. T
1.3 TapEko+Echo
The PCM 80 Tape Echo preset and a tap tempo echo, each with stereo output. T
1.4 PhoneInRoom
This is a dual mono in/stereo out ambience program. The left input feeds a speaker phone
filter which is then feed into a small room ambience. The right input is fed directly into the
room. ADJUST controls the apparent location of the speaker phone within the room.
Feed the signal intended for the speaker phone to the left input. Feed the signal for people
talking in the room to the right input.
1.5 TV In Room
This dual mono in/stereo out ambience program has the left input feeding a TV filter, which
is then feed into a small room ambience. The right input is fed directly into the room.
ADJUST controls the apparent location of the TV within the room. Feed the signal
intended for the TV to the left input. Feed the signal for the voices of the people watching
the TV to the right input.
1.6 Phone<>Room
This is a phone filter variation that allows you to swap between a sound source in a room,
and the sound source coming through a telephone. You could, for example, send the
same voice track into both inputs and use ADJUST to swap point of view with the person
speaking into a phone and some one listening to the phone. Click ADJUST from 0 to 1
to fade between the listener and the speaker— and from 1 to 0 to fade from the speaker
to the listener again. The AR Env controls the fade rates—it's in the Soft Row.
1.7 Flange+Ghost
The left and right inputs feed independent mono in/stereo out effects. The left input feeds
a stereo flanger. ADJUST controls the depth of the effect. The right input feeds a reverse
stereo reverb effect.
ADJUST: Eko Delay
ADJUST: Eko Slip
ADJUST: Ekos/Beat
ADJUST: FadeToPan
ADJUST: DlyTimeR
ADJUST: Phone Pan
ADJUST: TV Pan
ADJUST: Swap
ADJUST: Depth
Lexicon
0–100
0–100
0–100
0–100
0–127
0–100
0–100
0–100
0–100