Appendix B: Display Units - Lexicon MPX 1 V1.10 - MIDI IMPLEMENTATION DETAILS Midi Implementation Manual

MPX 1 V1.10 MIDI Implementation Details
0x38 Crossover Disp Units
0x39 Midrt Disp Units
0x3a Percent50 Disp Units
0x3b Msec Disp Units
0x3c Spread Disp Units
0x3d Shape Disp Units
0x3e Slope Disp Units
0x3f Dplevel Disp Units
0x40 Duration Disp Units
0x41 Cromatics Note Disp Units
0x42 AmbRtHc Disp Units
0x43 Word No Disp Units
0x44 Dump Disp Units
0x45 Feet Disp Units
0x46 Meters Disp Units
0x47 Phase Disp Units
0x48 Pdly Disp Units
0x49 Optimize Disp Units
0x4a Arp Velocity Source Disp Units If value is < 128, display as a decimal number otherwise subtract 127 and use 0x28
0x4b Control Level Disp Units
0x80 Level Disp Units
0x81 Pitch Disp Units
0x82 Bipolar Percentage Disp Units
0x83 Bipolar No Disp Units
0x84 Pan Disp Units
0x85 Bipolar Word Disp Units
0x86 FF "None" No Disp Units
0x87 Bipolar Degrees Disp Units
0x88 Bal Disp Units
0x89 Tone Level Disp Units
56
Use "reverb_freq_strings" offsetting the parameter value by 12. If value = 48 use "Flat".
If reverb algorithm is 1 or 5 use the "chamber_decay_strings", if 2 then use
"hall_decay_strings", if 3 use "plate_decay_strings"
Multiply value by 2 and display in decimal followed by '%'.
Display in decimal (optionally follow with "ms")
Display in decimal. Note that if "Link" is turned on, the value is scaled
Display in decimal
If the value is < 16, a minus sign is displayed followed by 16 minus the value in decimal.
Otherwise, a plus sign is displayed followed by the value minus 16 in decimal
If the value is 0, "Off" is displayed. If the value is the "max_value", "Full" is displayed.
Otherwise, a minus sign is displayed, the value is multiplied by 2 and used as an offset
into the "levelog_db" table, where the first display value is derived. The value is
incremented then used again for an index into the table for the second character.
Finally, the letters "dB" are tacked onto the end.
140 is added to the value multiplied by 5 (140+(value*5)) and displayed as decimal with
"ms" tacked onto the end.
The value has 12 subtracted from it until is less than 11 with the octave incremented
each time. The resulting "octave" number is displayed in hex followed by the note using
whats left of the value as an index into "cromatic_note_strings".
Use "ambience_RT_HC_strings"
Display as a decimal word (2 bytes)
Display "Dump"
Display in decimal (optionally add "Feet")
Display in decimal (optionally add "Meters")
Use "phase_strings"
Display in decimal (optionally add "ms")
Display in decimal using option data (optinally add "ms")
Controller Source Display Units.
Display the parameters name
If value = "min_value", display "Off" otherwise display a signed decimal number
followed by "dB".
Display as signed decimal number in 100ths (100 = "1.00")
Display as signed decimal number followed by "%".
Display as signed decimal number
If value = 0, display 'C' or "Center". If value is negative (MSB = 1), display (FF - value)
+ 1 in decimal followed by 'L' or "Left". If the value is positive, display the value in decimal
followed by 'R' or "Right".
Display in decimal word (2 bytes)
If the value is FF, display "None" otherwise, display "CC" followed by the value in
decimal.
Display in signed decimal (optionally add the degree symbol or the word "degrees")
Display in signed decimal.
Display in signed decimal followed by "dB".
Lexicon