Chapters
Table of Contents
Related Manuals for Lambda ZUP36-6
Summarization of Contents
CHAPTER 1. General Information
1.1 User manual content
Details the content of the user manual, including operating and installation instructions.
1.2 Introduction
Provides an overview of the ZUP series power supplies and their capabilities.
1.3 Accessories
Lists available accessories and their ordering numbers for the ZUP series.
CHAPTER 2. Specifications
2.1 SPECIFICATIONS: 200W/400W Series
Details the electrical and physical specifications for 200W and 400W ZUP series models.
2.2 Supplemental characteristics
Presents typical non-warranted performance characteristics for application assessment.
CHAPTER 3 INSTALLATION
3.1 GENERAL
Covers initial inspection, preparation, and repackaging for ZUP units.
3.2 INITIAL INSPECTION
Procedure for inspecting the power supply for damage after unpacking.
3.3 AC SOURCE REQUIREMENTS
Specifies the AC input voltage, frequency, and fluctuation limits for ZUP operation.
3.4 COOLING & PLACEMENT
Guidance on ensuring adequate airflow and suitable placement for the ZUP power supply.
3.5 RACK MOUNTING
Instructions for mounting ZUP models in a standard 19-inch rack.
3.6 POWER CONNECTION
Details on safely connecting the ZUP power supply to an AC power source.
3.7 CONNECTING THE LOAD
Provides guidance on connecting loads to the ZUP power supply, including wire selection.
3.8 EXTERNAL CONTROL CONNECTOR
Describes the external control connector for analog programming and signals.
3.9 REPACKAGING FOR SHIPMENT
Recommendations for safely repacking the ZUP unit for transportation.
CHAPTER 4 OPERATING INSTRUCTIONS
4.1 INTRODUCTION
Overview of ZUP power supply operating modes, front/rear panel controls, and indicators.
4.2 CONTROLS AND INDICATORS
Details the front panel controls and indicators of the ZUP series power supply.
4.3 TURN-ON CHECKOUT PROCEDURE
Step-by-step procedure for verifying ZUP power supply operation after turn-on.
4.4 LOCAL OPERATION
Describes operating the ZUP power supply using front and rear panel controls.
CHAPTER 5 RS232 & RS485 REMOTE CONTROL
5.1 INTRODUCTION
Overview of ZUP series serial communication port operation, setup, and protocol.
5.2 CONFIGURATION
Details on configuring ZUP units for RS232/RS485 communication, baud rate, and address.
5.3 REMOTE PROGRAMMING VIA RS232
Instructions for remote control of ZUP units using the RS232 interface.
5.4 REMOTE PROGRAMMING VIA RS485
Instructions for remote control of ZUP units using the RS485 interface.
5.5 ZUP SERIES COMMAND SET DESCRIPTION
Details the command set structure, syntax, and registers for ZUP series.
5.6 COMMUNICATION PROTOCOL
Defines the communication protocol, timing, and message structure for ZUP series.
5.7 SERVICE REQUEST
Explains Service Request (SRQ) generation and handling for ZUP power supply faults.
CHAPTER 6 MAINTENANCE
6.1 INTRODUCTION
Overview of maintenance procedures and calibration for ZUP power supply series.
6.2 UNITS UNDER WARRANTY
Procedure for returning ZUP units for repair during the warranty period.
6.3 PERIODIC MAINTENANCE
Instructions for routine cleaning and care of the ZUP power supply.
6.4 ADJUSTMENT AND CALIBRATION
Information on ZUP power supply adjustment, calibration, and service facility requirements.
6.5 PART REPLACEMENT AND REPAIRS.
Guidance on handling ZUP unit failures and contacting service facilities for repairs.
6.6 FUSE RATINGS
Lists the correct fuse types and ratings for various ZUP series models.
GLOBAL NETWORK
LAMBDA GROUP Europe / North America
Contact information for Lambda Group offices in Europe and North America.
DENSEI-LAMBDA GROUP Asia / Far East / Middle East
Contact details for Densei-Lambda Group offices in Asia, Far East, and Middle East.
Need help?
Do you have a question about the ZUP36-6 and is the answer not in the manual?
Questions and answers