Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for PowerBass XTA 6000D
Summarization of Contents
Amplifiers
Product Welcome and Features
Thanks for purchase, highlights Class-D tech and MOSFETs.
Class-D Bass Amplifier Description
Explains XTA series are single-channel for low frequencies and subwoofers.
Keys To Safe Installation
Charging System and Wiring Upgrades
Details necessary upgrades for alternator, batteries, and "BIG 3" wiring.
Fuse Placement and Wire Gauge
Specifies fuse locations and recommended wire gauges for safe installation.
Installation Preparation
Tools Required for Installation
Lists necessary tools for basic amplifier installation.
Installation Safety Precautions
Lists essential safety steps before and during the installation process.
Mounting the Amplifier
Optimal Mounting Location and Airflow
Explains importance of mounting for heat dissipation and proper airflow around the unit.
Installation Warnings and Fusing
Critical Installation Warnings
Lists crucial warnings about placement, upside-down mounting, and wire protection.
Fuse Rating Guidelines
Recommends specific fuse ratings for XTA6000D, XTA5000D, and XTA4000D models.
Control Panel Layout
Line Output and Input Jacks
Describes RCA LINE OUT and LINE IN jacks for signal routing.
Gain Control Adjustment
Explains how to match amplifier input sensitivity to the source unit.
Amplifier Controls Explained
Audio Filtering and Tuning Controls
Details Sub Sonic, LPF, Bass EQ, and Phase adjustments for audio tuning.
Linking and Remote Gain Controls
Covers MASTER/SLAVE switch, SLAVE jacks, and Remote Gain port.
Power and Remote Connections
Power Input Terminals (BATT+)
Details the BATT+ input terminals for connecting power cables.
Remote Input Terminal (REM)
Explains the REM terminal for turning the amplifier on/off.
Ground Input Terminal (GND)
Details the GND terminals for connecting to the vehicle chassis.
Wiring and Connections
Power Input Connections Diagram
Illustrates dual power input connections for XTA 6000D/5000D models.
Power and Ground Wiring
Battery (BATT+) Power Wiring
Guides on wiring the amplifier directly to the vehicle battery with proper fusing.
Ground (GND) Wiring
Details selecting and preparing a good ground point on the vehicle chassis.
Remote Connection Details
Connecting the Remote (REM) Terminal
Explains connecting the REM terminal to a switched +12V source for amplifier turn-on.
RCA Interconnect Wiring
Signal Cable Routing and Noise Prevention
Guides on selecting, routing, and crossing RCA cables to minimize noise.
User Adjustable Controls
Remote Gain Controller Connection
Explains connecting the remote gain control module for convenient adjustment.
Input Gain Adjustment Procedure
Details the three-step process for setting the input gain correctly.
Audio Tuning Adjustments
Bass EQ, LPF, Phase Controls
Explains Bass EQ, LPF, and Phase adjustments for sound tuning.
Sub Sonic Filter Importance
Emphasizes the critical importance of setting the Sub Sonic filter correctly for speaker protection.
Speaker Wiring and Load Management
Speaker Wire Selection and Connections
Guides on selecting speaker wire and ensuring correct polarity and connections.
Impedance and Bridging Limitations
Details minimum impedance loads and clarifies outputs should not be bridged.
Speaker Output Configurations
Single Voice Coil Subwoofer Wiring
Illustrates wiring for one or two single voice coil subwoofers.
Dual Voice Coil Subwoofer Wiring
Wiring for One/Three DVC Subwoofers
Shows wiring for one or three dual voice coil subwoofers with impedance calculations.
Four Single Voice Coil Subwoofer Wiring
Wiring Diagram for Four SVC Subwoofers
Illustrates wiring for four single voice coil subwoofers and notes the 1-ohm minimum.
Dual Link/Strapping Amplifiers
RCA Interconnect for Master/Slave Link
Shows RCA wiring for linking two amplifiers in master/slave configuration.
Speaker Wiring for Master/Slave Link
Illustrates speaker connections for master/slave dual link amplifiers.
Dual Link Speaker Connection Notes
Notes on Dual Link Speaker Connections
Provides specific notes on speaker connections for dual link setups, including impedance and model compatibility.
Testing Procedures
Post-Installation System Testing
Outlines tests for power wiring, speaker connections, and system operation.
Protection Indicator and Troubleshooting
Explains the RED LED and provides troubleshooting steps.
Recommended Wire Sizes Chart
Power Cable Gauge Selection Guide
Provides a chart to select power cable gauge based on fuse total and wire length.
Troubleshooting Common Issues
Power LED Not ON
Solutions for when the power LED is off, checking power and ground.
No Output with Green Power LED
Troubleshooting steps for no audio output with a green power indicator.
Status Protection LED Red
Addresses issues indicated by the red status LED, including overheating or voltage problems.
Alternator Noise and Poor Bass Response
Solutions for alternator noise and poor bass response by checking RCA and speaker connections.
Amplifier Specifications
Technical Specifications Summary
Details technical specifications for XTA 4000D, 5000D, and 6000D models.
Limited Warranty Policy
PowerBass Limited Warranty Terms
Outlines the terms and conditions of the PowerBass limited warranty for amplifiers.
Need help?
Do you have a question about the XTA 6000D and is the answer not in the manual?
Questions and answers