Advertisement
Table of Contents
- 1 Installation Instructions
- 2 Service Diagnosis
- 3 Harvest Cycle
- 4 Maintenance and Cleaning Instructions
- 5 Wiring Diagrams
- 6 Operation
- 7 Alarm Conditions
- 8 PC Board Set up
- 9 Removal and Replacement Procedures
- 10 Component Description
- 11 Service Specification
- 12 Specification
- 13 For the Plumber
- 14 For the Electrician
- Download this manual
See also:
Install and Operation Instructions
Advertisement
Table of Contents
Related Manuals for Foster 260
Summarization of Contents
F200 & F300 Modular Ice Cuber Specifications
1.1 Capacities
Details the various capacity metrics for the ice cuber models.
1.2 Installation Notes
Provides essential notes and considerations for the installation process.
1.3 Stacking Installation
Instructions and guidelines for stacking modular ice cuber units.
Installation Instructions
Warning!
Critical safety warnings for users performing installation or maintenance.
General Specifications
Overview of general specifications and approved standards for the ice machines.
Installation
Detailed steps and requirements for the physical installation of the machine.
2. Start Up
2.1 Start-up Cycle
Description of the initial start-up sequence and component operations.
2.2 Freezing Cycle
Details the process and components involved during the freezing cycle.
11. Maintenance and Cleaning Instructions
11.1 Ice Maker
Scheduled maintenance and cleaning procedures for the ice maker unit.
4. Operation
4.1 Refrigeration During Freeze
Explanation of the refrigeration system's function during the freezing phase.
4.2 Water System during freezing
Description of the water system's operation during the freezing cycle.
4.3 Ice harvest cycle
Details the process and components active during the ice harvest cycle.
4.4 Water system during ice harvest cycle
Description of the water system's function during the ice harvest phase.
4.5 Control sequence
Explanation of the sequence of operations controlled by the electronic board.
6. PC Board Set Up
6.1 Water Error
Details the 'Water Error' alarm condition and its reset mode.
6.2 Too High Condensing Temperature
Describes the 'Too High Condensing Temperature' alarm and reset procedure.
9. Removal and Replacement Procedures
9.1 Water Pump
Procedure for removing and replacing the water pump component.
9.2 Reservoir
Steps for the removal and replacement of the water reservoir.
9.3 Distributor/Water Tube
Instructions for removing and replacing the water distributor and tube.
9.4 Outlet Water Valve
Procedure for the removal and replacement of the water outlet valve.
9.5 Compressor
Guidelines for removing and replacing the compressor unit.
9.6 Condenser - Air Cooled
Procedure for removing and replacing the air-cooled condenser.
9.7 Condenser Water Cooled
Instructions for removing and replacing the water-cooled condenser.
9.8 Hot Gas Valve
Procedure for the removal and replacement of the hot gas valve.
9.9 Removal and Replacement of the Drier
Steps for removing and replacing the refrigerant drier.
7. Component Description
7.1 Front Console Panel
Description of the front console panel and its indicators.
7.2 P. C. Board
Details of the Printed Circuit Board, its functions, and jumpers.
7.3 Compressor Contactor
Description of the compressor contactor and its role.
7.4 Ice Thickness Sensor
Explanation of the ice thickness sensor and its operation.
7.5 Magnetic Switch
Description of the magnetic switch and its function in the cycle.
7.6 Hot Gas Valve
Explanation of the hot gas solenoid valve's function.
7.7 Condenser Temperature Sensor
Description of the condenser temperature sensor and its signaling.
7.8 High Pressure Control
Details on the high-pressure control safety device.
8. Wiring Diagram - F200 & F300
F200-F300 Wiring Diagram 220V 50Hz 1ph
Schematic wiring diagram for the F200/F300 models at 220V.
7. Service Specification
Operating Characteristics
Comparison of individual unit operating characteristics to a normally operating machine.
Freeze Cycle
Specification data related to the freeze cycle parameters.
Harvest Cycle
Specification data related to the harvest cycle parameters.
10. Maintenance, Cleaning and Sanitation Instructions
10.1 Icemaker
Scheduled maintenance and cleaning for the icemaker unit.
10.2 Ice Storage Bin
Procedures for cleaning and sanitizing the ice storage bin.
10.3 Cabinet Exterior
Instructions for cleaning the exterior of the machine and ice bin.
10.4 Cleaning Ice Maker
Detailed steps for cleaning the ice maker unit using specific solutions.
6. Operation
6.1 Refrigeration During Freeze
Explanation of the refrigeration system during the freeze phase.
1. Specification
FMIC180
Specifications for the FMIC180 model.
FMIC 260
Specifications for the FMIC 260 model.
FMIC 180 Machine Specifications - R22 Machines
Detailed specifications for FMIC 180 using R22 refrigerant.
FMIC 180 Machine Specification R404A Machines
Detailed specifications for FMIC 180 using R404A refrigerant.
FMIC 260 Machine Specifications - R22 Machines
Detailed specifications for FMIC 260 using R22 refrigerant.
FMIC 260 Machine Specification R404A Machines
Detailed specifications for FMIC 260 using R404A refrigerant.
Freeze Cycle R404A Machines
Freeze cycle parameters for R404A machines.
2. For The Installer
2.1 Important Operating Requirements
Key operating requirements for installers.
2.2 Select Location
Guidance on selecting an appropriate location for installation.
2.3 Ice Machine
Specifics regarding the ice machine unit itself during installation.
2.4 Final Check List
A checklist for final verification before completing installation.
3. For The Plumber
3.1 Conform To Applicable Codes
Ensuring plumbing work conforms to all relevant codes and regulations.
3.2 Water Inlet
Procedures and considerations for the water inlet connection.
3.3 Drains
Guidelines and requirements for drain connections.
5. Start-Up
5.1 Start-Up
Initial steps for starting up the ice maker unit.
5. Start-Up
5.1 Start-Up
Continuation of the initial start-up procedure and checks.
Need help?
Do you have a question about the 260 and is the answer not in the manual?
Questions and answers