Advertisement
4/23/10
This procedure is used to update Main CPU Ver.
flash programming for the FT-2000/D Transceivers.
We recommend installing the Flash Programming Software on a PC computer with Windows 2000,
XP or Vista Operating System; and use the CT-119 programming cable or 8-pin mini-DIN PGM-SW
(P0091526) and serial cable RS-232C, DB9F to DB9F straight cable.
NOTE: There are many USB adapters available; however some may not function with this software.
We recommend using the latest USB adapter driver software when available.
The update software is available from our website at http://www.yaesu.com. The CT-119
programming cable is available from your authorized Vertex Standard dealer. You may also order
by email to Vertex Standard parts department, yaesuparts@vxstdusa.com.
If the CT-119 programming cable or is not available you will need a RS-232C, DB9F to DB9F
straight cable and 8pin mini-DIN PGM-SW (P0091526). If the DIN PGM-SW is not available you
will need to operate the internal program switch S3004. Please follow the instructions in
Addendum: Page 7 and 9.
The software versions can be displayed on the radio
While holding the three buttons [GEN]＋[50]＋[ENT] turn the radio on. The software version will be
displayed in the VFO-A window for 5 seconds then the radio will start up in normal operation.
See below:
Example EDSP V11.53 and MAIN V0150 software version.
EDSP:
Software version
11.XX
(This image & version is for
illustration only)
*If you already have
EDSP
2000/D again.
The software updates will work with all versions (AF, AS, EU, NA, OC, SA or all Countries) of the
PEP2000
V11.54
and MAIN
V0151
software versions,
FT-2000 and FT-2000D.
0151
and EDSP Ver.
Main CPU:
Software version
(This image & version is for
illustration only)
it is not necessary to update the FT-
11.54
the
01 XX
Advertisement
Table of Contents
Related Manuals for Yaesu FT-2000D - UPDATE V0151 AND V11.54 INFORMATION
Summary of Contents for Yaesu FT-2000D - UPDATE V0151 AND V11.54 INFORMATION
- Page 1 NOTE: There are many USB adapters available; however some may not function with this software. We recommend using the latest USB adapter driver software when available. The update software is available from our website at http://www.yaesu.com. The CT-119 programming cable is available from your authorized Vertex Standard dealer. You may also order by email to Vertex Standard parts department, yaesuparts@vxstdusa.com.
- Page 2 Please check your menu, update the settings, and then save the new settings to the CF card. Install the data file to PC 1. Down load the FT-2000 data file [FT-2000_PEP2000_4-23-10.zip] from the following website: http://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=66EA 91711DFB68C03DED4AD35153E12C&DivisionID=65&isArchived=0 2. Save the FT-2000 data file [FT-2000_PEP2000_4-23-10.zip] to the desktop on your computer.
- Page 3 Connect the CT-119 Cable’s DB9F connector to the serial port COM1 in the back of your computer. If you use a USB to serial adapter, you might need to change the COM Port number. Now go to the desktop open PEP2000_MAIN folder and find the FSW003 icon as shown below.
- Page 4 8-pin mini-DIN PGM-SW 1. Turn the main REAR power switch OFF. 2. Connect a RS-232C straight cable to the CAT connector. EDSP 3. Open the file FSW003. 4. Insert the 8-pin mini-DIN PMG-SW connector to FT-2000/D (PMG) jack. 5. Turn on the REAR Main power switch. 6.
- Page 5 EDSP and the Main CPU, you may wish to make new settings. We hope this new software will increase your enjoyment of your FT-2000/D. Thank you for choosing Yaesu radios. If you have any problems or questions please contact Vertex Standard, Amateur Tech Support.
- Page 6 ADDENDUM If the CT-119 programming cable or 8-pin mini-DIN PGM-SW (P0091526) is not available you will need a serial cable RS-232C, DB9F to DB9F straight cable. Please follow these instructions. MAIN Software Update *Don't forget to write down (or save to a CF Card) any personal menu settings you have changed from the default before you start.
- Page 7 Now go to the desktop open PEP2000_MAIN folder and find the FSW003 icon as shown below. Double-click the FSW003 icon, displayed on the Program Screen. NOTE: I f you receive a “communications error” message on your screen, click on the Configure box and choose a different COM port from the drop down menu.
- Page 8 Figure A left Remove the rear foot (near the CAT connector) expose the program switch access hole. Switch S3004 is visible through the hole. Move the switch to the on (rear) position. (Top of picture) This is just a screw hole for reference...
Need help?
Do you have a question about the FT-2000D - UPDATE V0151 AND V11.54 INFORMATION and is the answer not in the manual?
Questions and answers