Set" (Menu) Mode - Yaesu FT-1900R Operating Manual

"S " M
ET
The FT-1900R Set (Menu) mode, already described in parts of many previous chapters, is
easy to activate and set. It may be used for configuration of a wide variety of transceiver
parameters, some of which have not been detailed previously. Use the following procedure
to activate the Set (Menu) mode:
1. Press and hold in the [ MHz ( SET )] key for one second to enter the Set mode.
2. Rotate the DIAL knob to select the Menu Item to be adjusted.
3. Press the [ MHz ( SET )] key momentarily to enable adjustment of the selected Menu
item, then rotate the DIAL knob to perform the actual adjustment.
4. After completing your selection and adjustment, press and hold in the [ MHz ( SET )] key
for one second to exit the Set mode and resume normal operation.
M I F
1 APO Enables/Disables the Automatic Power Off feature.
2 AR BEP Selects the Beep option during ARTS™ operation.
3 AR INT Selects the Polling Interval during ARTS™ operation.
4 ARS Activates/Deactivates the Automatic Repeater Shift feature.
5 BCLO Enables/Disables the Busy Channel Lock-Out feature.
6 BEEP Enables/Disables the key beeper.
7 BELL Selects the CTCSS/DCS/EPCS Bell Ringer repetitions.
8 BNK.LNK Select the Memory Bank for the Memory Bank Link Scan.
9 BNK NM Programming an Alpha/Numeric label for a Memory Bank.
10 CLK.SFT Shifting of the CPU clock frequency.
11 CW ID Enables/Disables the CW identifier during ARTS™ Operation.
12 CWTRNG Enables/Disables the CW Training feature and selects the sending
speed of the morse Code.
13 DC VLT Indicates the DC Supply Voltage.
14 DCS CD Setting of the DCS code.
15 DCS RV Enables/Disables "Inverted" DCS code decoding.
16 DIMMER Setting of the front panel display's illumination level.
17 DT A/M Enables/Disables the DTMF Autodialer feature.
18 DT DLY Setting of the DTMF Autodialer's TX Delay Time.
19 DT SET Loading of the DTMF Autodialer Memories.
20 DT SPD Setting of the DTMF Autodialer Sending Speed.
21 EDG.BEP Enables/Disable the Band-edge beeper while scanning.
Selects the Access Number ( DTMF digit ) for WiRES™ operation.
22 INT CD
23 INT MD Selects the Internet Link Connection mode.
24 INT.A/M Enables/Disables DTMF Autodialer feature while operating on the
Internet Connection feature.
Selects the memory register for an Access Number ( DTMF code ) for
25 INT.SET
non-WiRES™ Internet Link System access.
26 LOCK Selects the Control Locking Lockout combination.
27 MCGAIN Adjust the microphone gain level.
28 MEM.SCN Selects the Memory Scan mode.
70
M
ENU ODE
A V
30MIN / 1HOUR / 3HOUR /
5HOUR / 8HOUR / OFF
IN RNG / ALWAYS / OFF
25SEC / 15SEC
ON / OFF
ON / OFF
KY+SCN / KEY / OFF
1 / 3 / 5 / 8 / CNTNUE / OFF
---
---
ON / OFF
ON / OFF
4WPM - 13WPM / 15WPM /
17WPM / 20WPM / 24WPM /
30WPM / 40WPM / OFF
( 20CPM - 65CPM ( 5CPM multiples )
/ 75CPM / 85CPM / 100CPM /
120CPM / 150CPM / 200CPM )
---
104 standard DCS codes
ENABLE / DISABL
LVL 0 ( OFF ) - LVL 10
MANUAL / AUTO
50 / 250 / 450 / 750 / 1000 ( ms )
---
50 / 100 ( ms )
ON / OFF
DTMF 0 - DTMF 9 /
DTMF A -DTMF F
SRG / FRG
MANUAL / AUTO
---
KEY / DIAL / K+D / PTT /
K+P / D+P / ALL
LVL 1 -LVL 9
TAG1 / TAG2 / ALL CH
FT-1900R O
D
OFF
IN RNG
25SEC
ON
OFF
KY+SCN
OFF
---
---
OFF
OFF
OFF
---
023
DISABL
LVL 5
MANUAL
450 ( ms )
---
50 ( ms )
OFF
DTMF 1
SRG
MANUAL
---
K+D
LVL 5
ALL CH
M