NEC LCD2690WUXI2-BK - MultiSync - 26" LCD Monitor User Manual page 21

Tag2 R-H.position
(Analog input only)
G-H.position
(Analog input only)
B-H.position
(Analog input only)
R-FINE
(Analog input only)
G-FINE
(Analog input only)
B-FINE
(Analog input only)
R-SHARPNESS
(Analog input only)
G-SHARPNESS
(Analog input only)
B-SHARPNESS
(Analog input only)
DVI Long Cable
(Digital input only)
Tag3 Auto Adjust
(Analog input only)
Signal Adjust
(Analog input only)
Auto Adjust Level
(Analog input only)
A-NTAA SW
(Analog input only)
Tag4 H. Position
V. Position
Adjusts the position of the red component of the image. Press "Left" or "Right" to adjust.
Adjusts the position of the green component of the image. Press "Left" or "Right" to adjust.
Adjusts the position of the blue component of the image. Press "Left" or "Right" to adjust.
Adjusts the "FINE" setting of the RED component of the image.
Press "Left" or "Right" to adjust.
Adjusts the "FINE" setting of the GREEN component of the image.
Press "Left" or "Right" to adjust.
Adjusts the "FINE" setting of the BLUE component of the image.
Press "Left" or "Right" to adjust.
Adjusts the sharpness of the red component of the image. Press "Left" or "Right" to adjust.
Adjusts the sharpness of the green component of the image.
Press "Left" or "Right" to adjust.
Adjusts the sharpness of the blue component of the image.
Press "Left" or "Right" to adjust.
Compensates for image degradation caused by using a long DVI cable.
There are 4 possible settings, with "0" being the lowest level of compensation and
"3" being the highest level. The default setting is "1".
Automatically adjusts the Image Position and H.Size settings and Fine settings.
Press "SELECT" to activate Auto Adjustment.
Determines when the auto adjustment is activated automatically.
The choices are "SIMPLE" and "FULL". Press "Left" or "Right" to select.
H-size, Fine, H/V Position
SIMPLE O
FULL O
O: Automatic Adjustment X: No Automatic Adjustment
NOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.
Determines the automatic adjustment level for Auto Adjust. The choices are "SIMPLE",
"FULL" and "DETAIL". Press "Left" or "Right" to select. Refer to the below table.
Size, Fine, Position
SIMPLE O
FULL O
DETAIL* O
O: Automatic Adjustment X: No Automatic Adjustment
* "DETAIL" activates automatic long cable (skew, peaking) adjustment.
** Black level, RGB sharpness, RGB delay and RGB position are adjusted using "Long cable software"
which is included in the attached CD-ROM.
The Advanced No Touch Auto Adjust function is able to recognize new signals even when
neither the resolution nor the refresh rate has changed. If several PCs are connected to
the monitor, and each transmit very similar (or even the same) signals in terms of
resolution and refresh rates, the monitor recognizes that there is a new signal and
automatically optimizes the picture without the need for any action on the part of the user.
OFF: A-NTAA is disabled.
ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal settings
for the new signal. If no change in the signal is detected then A-NTAA does not activate.
The screen will be blank while the monitor optimizes the signal.
OPTION: Functions the same as ON, except that the screen does not go blank when the
monitor makes adjustments for changes in signal, allowing the monitor to display the new
signal faster. When using an external switching device to connect 2 or more PCs to the
monitor, using the ON or OPTION settings is suitable.
Controls Horizontal Image Position within the display area of the LCD.
Press "Left" or "Right" to adjust.
Controls Vertical Image Position within the display area of the LCD.
Press "Left" or "Right" to adjust.
English-19
Contrast
X
O
Contrast Black Level,
Long cable capability**
X X
O X
O O
Time
1 second
1.5 seconds
5 seconds