Advertisement
Quick Links
60-120 min
Cutting Not
Required
Drilling May
Required
Part List
#1: Driver Side Front/Center & Passenger Side Rear Brackets x 3
#2: Passenger Side Front/Center & Driver Side Rear Brackets x 3
#3: Driver Side Front/Center & Passenger Side Rear Support Brackets x 3
#4: Passenger Side Front/Center & Driver Side Rear Support Brackets x 3
www.tacautoparts.com
SIDEWINDER RUNNING BOARD
FITS:
Torque & Tools
Fastener
Tightening Torque
Size
(ft-lbs)
6mm
7-8.5
8mm
18-20
10mm
35-40
12mm
60-70
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
ASSISTANCE IS RECOMMENDED.
"08-L" for
Left/Driver Side
#3
#1
#3
#1
#2
#4
PART #: SW-D08N
2009-2018 Dodge RAM 1500 Crew Cab
2019-2023 Dodge RAM 1500 Classic Model Crew Cab
2010-Up Dodge RAM 2500 / 3500 Crew Cab
Wrench Required
Front
#2
#2
#3
Customer Support: tac-office@tacautoparts.com
Allen Wrench
Required
■
10mm
■
13mm
□ 16mm
□ 18mm
"08-R" for Right
/Passenger Side
#4
#4
#1
□ 4mm
□ 5mm
□ 6mm
□ 8mm
Advertisement
Related Manuals for TAC SW-D08N
Summary of Contents for TAC SW-D08N
- Page 1 SIDEWINDER RUNNING BOARD PART #: SW-D08N 2009-2018 Dodge RAM 1500 Crew Cab FITS: 2019-2023 Dodge RAM 1500 Classic Model Crew Cab 2010-Up Dodge RAM 2500 / 3500 Crew Cab Torque & Tools Fastener Tightening Torque Allen Wrench Wrench Required 60-120 min...
- Page 2 8mm Bolt/Nut 8mm Plastic 8mm x 30mm 8mm Flat 8mm Lock Plate Retainer Hex Bolt Washer Washer 8mm x 25mm 8mm Hex Nut 8mm Nylon 6mm x 25mm 6mm Nylon 6mm Flat Combo Bolt Lock Nut Hex Bolt Lock Nut Washer PLEASE NOTE THAT THE FOLLOWING STEP 2.1...
- Page 3 Remove the 8mm Hex Bolt from the nut on the b. Thread (1) 8mm Plastic Retainer onto the Bolt Plate from Step 2a. Rotate the Bolt on the threaded end and down tight against the body Bolt Plate until the threaded nut lines up with panel, (Fig 3).
- Page 4 FIG 7 STEP 4 Attach the Support Bracket to the Mounting Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (2) 8mm Hex Bolts (1) 8mm Nylon Lock Nut, (Fig 9). IMPORTANT: (2) 8mm Lock Washers (2) 8mm Flat Washers 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket.
- Page 5 STEP 5 STEP 7 Move along the side of the body panel to the Select the Driver/Left Running Board. NOTE: The center mounting location, (Fig 10). Repeat Steps Driver/Left Running Board will have a “08-L” on the 1—4 to install (1) Driver/Left Center Bracket (#1) front of the Running Board.
- Page 6 Attention STEP 9 To protect your investment, do not use Repeat Steps 1—8 to attach the Passenger/Right any type of polish or wax that may contain Running Board. abrasives that could damage the finish. Mild soap may be used also to clean the Running Boards.
Need help?
Do you have a question about the SW-D08N and is the answer not in the manual?
Questions and answers