Advertisement
Quick Links
60-120 min
Cutting Not
Required
Drilling May
Required
Part List
#1
#3
#3
#1: Driver/Left Side Front Bracket x 1
#2: Passenger/Right Side Front Bracket x 1
#3: Driver/Left Side Center/Rear Bracket x 2
#4: Passenger/Right Side Center/Rear Bracket x 2
#5: Driver Side Front & Passenger Side Center/Rear Support Bracket x 3
#6: Passenger Side Front & Driver Side Center/Rear Support Bracket x 3
www.tacautoparts.com
2009-2018 Dodge RAM 1500 Crew Cab
FITS:
2019-2023 Dodge RAM 1500 Classic Model Crew Cab
2010-Up Dodge RAM 2500 / 3500 Crew Cab
Torque & Tools
Fastener
Tightening Torque
Size
(ft-lbs)
■
■
6mm
7-8.5
■
■
8mm
18-20
□ 10mm
□ 35-40
□ 12mm
□ 60-70
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
ASSISTANCE IS RECOMMENDED.
Sticker "D" for
Driver / Left Side
#5
#6
#6
ARROW SIDE STEP
PART #: TB-D08
Wrench Required
■
■
□ 16mm
□ 18mm
Sticker "P" for
Front
Passenger / Right Side
#5
#5
Customer Support: tac-office@tacautoparts.com
Allen Wrench
Required
10mm
13mm
#6
#2
#4
#4
□ 4mm
□ 5mm
□ 6mm
□ 8mm
Advertisement
Summary of Contents for TAC TB-D08
- Page 1 ARROW SIDE STEP PART #: TB-D08 2009-2018 Dodge RAM 1500 Crew Cab FITS: 2019-2023 Dodge RAM 1500 Classic Model Crew Cab 2010-Up Dodge RAM 2500 / 3500 Crew Cab Torque & Tools Fastener Tightening Torque Allen Wrench Wrench Required 60-120 min...
- Page 2 8mm Bolt/Nut 8mm Plastic 8mm x 30mm 8mm Flat 8mm Lock 8mm Hex Plate Retainer Hex Bolt Washer Washer 8mm Nylon 6mm x 20mm 6mm x 25mm 6mm Flat 6mm Lock 6mm Hex 6mm Nylon Lock Nut T-Bolt Hex Bolt Washer Washer Lock Nut...
- Page 3 b. Thread (1) 8mm Plastic Retainer onto the d. Remove the 8mm Hex Bolt from the nut on the threaded end and down tight against the body Bolt Plate from Step 2.1a. Rotate the Bolt on panel, (Fig 3). NOTE: The Plastic Retainer is the Bolt Plate until the threaded nut lines up designed to keep the Bolt/Nut Plate from with the remaining hole in the Mounting...
- Page 4 FIG 7 STEP 4 Attach the Support Bracket to the Mounting (2) 8mm Hex Bolts Bracket with (1) 8mm Hex Bolt, (2) 8mm Flat (2) 8mm Lock Washers (2) 8mm Flat Washers Washers and (1) 8mm Nylon Lock Nut, (Fig 9). Front FIG 9 8mm Hex Bolt...
- Page 5 FIG 13 STEP 6 Move to the rear location, (Fig 11). Repeat Steps 1-4 to attach (1) Driver/Left Center/Rear Mounting Bracket (#3) and (1) Driver Side Center/Rear Support Bracket (#6) to the Driver/Left rear mounting location. FIG 11 (2) 6mm Flat Washers (2) 6mm Lock Washers (2) 6mm Hex Nuts (Fig 13) Attach the Driver/Left Side Step to the (3)
- Page 6 Attention STEP 9 To protect your investment, do not use any type of polish or wax that may contain Repeat Steps 1-8 to attach the Passenger/Right abrasives that could damage the finish. Side Step. Mild soap may be used also to clean the Side Steps.