Advertisement
Quick Links
13149
3/26/2020
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH:
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH:
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
Parts List
ITEM
QTY
PART NUMBER
4
1
10-10275
HHCS,M12x1.25,35,CL10.9,YZ
2
4
30-00149
WASHER,S-CON,1/2,YZ
2
1
HITCH WEIGHT:
34
LBS.
INSTALL TIME
PROFESSIONAL:
15
MINUTES
NOVICE (DIY):
30
MINUTES
INSTALL NOTES:
- EXISTING WELDNUTS
- NO DRILLING REQUIRED
- REMOVE TIE DOWN BRACKET
- LOWER EXHAUST
INSTALLATION STEPS
1. If present remove panel and trim using panel trim diagram above as reference.
Remove tie down bracket from the driver's side of the vehicle and return to vehicle owner.
2. Lower rear most exhaust isolator for ease of installment.
3. Raise hitch into position over existing weldnuts and install the supplied 12mm hex bolts and conical tooth
washers as shown.
4. Raise exhaust back into location and reinstall rubber isolator.
5. Torque hardware to 86 lb-ft.
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
TOYOTA RAV 4 (EXCLUDING ELECTRIC)
TOOLS REQUIRED
17, 19mm SOCKET
DESCRIPTION
SOCKET WRENCH
TORQUE WRENCH
1.500 in
PANEL TRIM DIAGRAM
EXISTING WELDNUTS
(BOTH SIDES)
DRIVER SIDE FRAME RAIL
3,500
LBS. TRAILER WEIGHT &
4,000
LBS. TRAILER WEIGHT &
8" EXTENSION
USE RIB AS GUIDE
525
LBS. TONGUE WEIGHT.
LBS. TONGUE WEIGHT
525
1-877-287-8 34
6
PASSENGER SIDE
FRAME RAIL
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for curt 13149
Summary of Contents for curt 13149
- Page 1 ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase.
- Page 2 CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace...
- Page 3 INSTALLATION WALKTHROUGH: 1. If present remove panel and trim using panel trim ITEM PART NUMBER DESCRIPTION diagram below as reference. Remove the tie 10-10275 HHCS,M12x1.25,35,CL10.9,YZ 30-00149 WASHER,S-CON,1/2,YZ down bracket from the drivers side frame rail using the 17mm socket, 8" extension and ratchet. Return the bracket and fasteners to vehicle owner.
- Page 4 INSTALLATION WALKTHROUGH: 3. Raise hitch into position over existing weldnuts 5. Torque hardware to 86 lb-ft. and install the supplied 12mm hex bolts and conical tooth washers as shown. 4. Raise exhaust back into location and reinstall rubber isolator. Install now complete For more information log onto www.curtmfg.com, &...
- Page 5 TOWING SAFETY INFORMATION...
Need help?
Do you have a question about the 13149 and is the answer not in the manual?
Questions and answers