Page of 2

Delta Electronics Programmable Logic Controller DVP-EC3 Instruction Sheet

Dvp-ec3 series programmable logic controller.
Hide thumbs
   

Advertisement

Warning
This instruction sheet provides only information on the electrical specification, general functions, installation and
wiring. The program design and applicable instructions for DVP-EC3 are the same as those applicable for DVP-ES
series. For detailed information, please refer to "DVP-PLC Application Manual: Programming". For details of the
optional peripheral, please refer to the instruction sheet enclosed in it.
DVP-EC3 series PLC is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne
dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the
device (e.g. key or specific tools are required for operating the enclosure) in case danger and damage on the device
may occur.
DO NOT connect the input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check
all the wiring again before switching on the power. Make sure the ground terminal
is correctly grounded in order
to prevent electromagnetic interference.
Introduction
Thank you for choosing Delta DVP-EC3 series programmable logic controller. DVP-EC3 currently offers 10-16
I/O points. To ensure proper installation, operation and maintenance, please read this instruction sheet carefully
and provide users with this instruction sheet before installing DVP-EC3.
Product Profile & Outline
P OW ER , R U N & ER RO R in dic a tors
Inpu t po ints Ind ic atio n
C OM 2 C om mun ica tion
D ir ec t m oun ting ho le
p ort
(RS- 48 5 )
+24 V24 G S/ S X 0 X 1 X 2 X3 X 4 X5 X 6 X 7
D + D - S G
D C p ow e r s u pp ly o u tpu t
COM2
I/O p oin t in dica to rs
POWE R
R UN
ER ROR
M od el n a me
DVP1 6EC
C OM 1 C om mu n ica tion
8DI-DC / 8DO-R
COM1
por t
(RS-23 2C)
A C p ow e r s u pp ly in put
L
N
C 0 Y0 Y1 Y 2 Y 3 C 1 Y 4 Y 5
Y 6 Y 7
O utp ut points In d ic a tio n
D IN r ail (35m m)
D ir ec t m ou ntin g ho le
D IN rail c lip
F ix ed I/O te r min als
Dimensions
+24V 24G S/S X0 X1 X2 X3
X4 X5 X6 X7
D+ D- SG
COM2
IN
0 1 2 3 4 5 6 7
PO WE R
RUN
OUT
0 1 2 3 4 5 6 7
E RRO R
99 m m
90m m
DVP16EC
8DI-DC / 8DO-R
COM1
A C 1 00 ~2 4 0V
I NP U T
L
N
C0 Y0 Y1 Y2 Y3 C1 Y4
Y5
Y6 Y7
9 0.5 m m
4 8.5 m m
95 m m
Specifications
Model
DVP10EC00 3
DVP14EC00 3
Item
Power supply voltage
100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
DVP-EC3 starts to run when the power supply rises to 95 ~ 100V AC and stops
Operation
when the power supply drops to 70V AC. It continues to run for 10ms after the
power supply is cut off.
Power supply fuse
2A/250V AC
Power consumption
9VA
DC24V Supply Current
100mA
Power supply protection
DC24V output short circuit protection
1,500V AC (Primary-secondary), 1,500V AC (Primary-PE), 500V AC
Voltage withstand
(Secondary-PE)
Insulation resistance
> 5M at 500V DC (between all I/O points and earth)
ESD: 8KV Air Discharge
Noise immunity
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
RS: 26MHz ~ 1GHz, 10V/m
The diameter of grounding wire shall not be less than that of L, N terminal of the
Earth
power supply. (When many PLCs are in use at the same time, please make sure
every PLC is properly grounded.)
Operation: 0° C ~ 55° C (temperature), 50 ~ 95% (humidity), Pollution degree2
Operation/storage
Storage: -25° C ~ 70° C (temperature), 5 ~ 95% (humidity)
Vibration/shock
International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC
resistance
68-2-27 (TEST Ea)
RS-485 communication
Not supported
Not supported
mode
Weight (g)
R: 192g; T: 180g
R: 202g; T: 185g
Input Point
Input point type
Digital Input
Input type
DC (SINK or SOURCE)
Input current
24V DC 5mA
Off → On, > 15V DC
Action level
On → Off, < 5V DC
Reaction time
Approx. 10ms (0 ~ 20ms adjustable in D1020)
(Conversion sampling
time)
Output Point
Output point type
Relay-R
Current specification
2A/1 point (5A/COM)
Voltage specification
< 250V AC, 30V DC
75VA (inductive)
Maximum load
90W (resistive)
Reaction time
Approx .10ms
Installation & Wiring
ENGLISH
3.1 I/O Terminal Layout
DVP10EC00R3/T3
S/S
X0
X1
X2
X3
X4
X5
S/S
+24V
24G
+24V
24G
D VP 10EC 00R3 (6DI -DC / 4D O-R)
DVP10EC00T3 (6DI- DC / 4DO- T)
C0
Y0
Y1
Y2
Y3
DVP14EC00R3/T3
S/S
X0
X1
X2
X3
X4
X5
X6
X7
+24V
24G
DVP14EC00R3 (8DI-DC / 6DO-R)
C0
Y0
Y1
Y2
Y3
C1
Y4
Y5
S/S
X0
X1
X2
X3
X4
X5
X6
X7
+24V
24G
D VP14EC 00T3 (8DI-DC / 6DO-T)
UP
ZP
Y0
Y1
Y2
Y3
Y4
Y5
DVP16EC00R3/T3
S/S
X0
X1
X2
X3
X4
X5
X6
X7
D+
D-
+24V
24G
DVP16EC00R3 (8DI-DC / 8DO-R)
C0
Y0
Y1
Y2
Y3
C1
Y4
Y5
Y6
+24V
24G
S/S
X0
X1
X2
X3
X4
X5
X6
X7
D+
D-
DVP16EC00T3 (8DI-DC / 8DO- R)
UP
ZP
Y0
Y1
Y2
Y3
Y4
Y5
Y6
1. Use the 12-24 AWG single-core bare wire or the multi-core wire for the I/O wiring, and please use 60/75° C
copper conductor only. The twisting power of the screw for the DVP-EC3 terminal is 3.80 kg-cm (3.30
lb-in) .
2. DO NOT wire empty terminal. DO NOT place the input signal wire and output power wire in the same
wiring circuit.
3. DO NOT drop tiny metallic conductor into DVP-EC3 while screwing and wiring
3.2 Mounting & Installation
Please install PLC in an enclosure with sufficient space around it to allow heat dissipation. For heat
dissipation, make sure to provide a minimum clearance of 50mm between the unit and all sides of the cabinet.
(See the figure.)
How to screw: Please use M4 screw according to the dimension of the product.
How to install DIN rail: PLC can be secured to a cabinet by using the 35mm DIN rail. When mounting PLC to
DIN rail, be sure to use the end bracket to stop any side-to-side movement of it and reduce the change of
wires being loosen. A small retaining clip is at the bottom of it. To secure PLC to DIN rail, place the clip onto
the rail and gently push it up. To remove it, pull the retaining clip down and gently remove it from DIN rail.
3.3 Wiring Notes
Specification & Wiring of Power Supply
The power supply input for DVP-EC3 model is AC input. When operating DVP-EC3, please make sure that:
1. The input voltage should be 100 ~ 240VAC. The power supply should be connected to L and N terminals.
Please note that wiring AC110V or AC220V to +24V output terminal or digital input points will result in
serious damage on it.
DVP16EC00 3
2. Use 1.6mm wire (or longer) for the grounding of it.
3. The power shutdown of less than 10ms will not affect the operation of it. However, power shutdown time
that is too long or the drop of power supply voltage will stop the running of it, and all outputs will go "OFF".
When the power supply turns normal again, DVP-EC3 will automatically return to its operation. (Please be
aware of the latched auxiliary relays and registers inside DVP-EC3 when programming.)
4. For max. output of the +24V power supply output terminal for each model, please refer to the electrical
specification table. DO NOT connect other external power supplies to this terminal. Every input point
requires 5 ~ 7mA to drive (e.g. 16 input points will require 80 ~ 112mA to drive). The +24V input on DVP-
EC3 is only for digital input points; other external loads are not suggested.
5V
DC/DC
100~240VAC
Safety Wiring
Since DVP-EC3 controls many devices, actions of any device may affect actions of other devices, and the
breakdown of any one device may cause the breakdown of the entire auto-control system and danger.
Supported
Therefore, we suggest you wire a protection circuit at the power supply input terminal, as shown in the figure
R: 212g; T: 190g
below.
Transistor-T
I/O Point Wiring
0.5A/1 point (2A/COM)
The input signal of the input point is the DC power DC input. There are two types of DC type wiring: SINK and
5 ~ 30V DC
SOURCE, defined as follows:
(UP, ZP must work wit external
Input Point Loop Equivalent Circuit & Wiring
auxiliary power supply 24V DC -15%
~ +20%, rated consumption approx.
1mA/point)
15W/1 point (Resistive)
Off
On 30us, On
Off 100us
DC Signal IN
(SINK mode)
X0
X1
X2
X3
X4
X5
UP
ZP
Y0
Y1
Y2
Y3
DC Signal IN
(
SOURCE mode)
SG
Y7
Below is an example. For detailed point configuration, please refer to specifications of each model:
SG
Relay (R) Output Circuit Wiring
Y7
Transistor (T) Output Circuit Wiring
注 意 事 項
DVP-ES
產 品 簡 介
+2 4V
24G S/S
X0
X1
X2
DVP-EC3
產 品 外 觀 及 各 部 介 紹
2. 0A
L
N
1
AC power supply load
2
Power supply circuit protection fuse (3A)
3
POWER indicator
Emergency stop: This button can cut off the system
4
power supply when accidental emergency takes place
尺 寸 規 格
5
Breaker
6
DVP-EC3 (main processing unit)
7
Earth resistance: < 100
8
Power supply: 100 ~ 240V AC, 50/60Hz
電 氣 規 格
+5 V
+24 V
24V D C
24 G
S/ S
X0
X1
+24V
DC24V
24VDC
+5V
24G
S/S
X0
X1
1
Flywheel diode: To extend the life span of contact
/
2
Emergency stop: Uses external switch
Fuse: Uses 5 ~ 10A fuse at the shared terminal of
3
/
output contacts to protect the output circuit
RS-485
4
Varistor: To reduce the interference on AC load
,g
5
Empty terminal: Not in use
6
DC power supply
7
Neon indicator
8
AC power supply
9
Incandescent light (resistive load)
Manually exclusive output: Uses external circuit and
forms an interlock, together with DVP-EC3 internal
10
program, to ensure safety protection in case of any
unexpected errors.
1
DC power supply
2
Emergency stop
3
Circuit protection fuse
The output of the transistor model is "open
collector". If Y0/Y1 is set to pulse output, the output
4
current has to be 0.05 ~ 0.5A to ensure normal
operation of the model.
Manually exclusive output: Uses external circuit and
forms an interlock, together with DVP-EC3 internal
5
program, to ensure safety protection in case of any
unexpected errors.
繁 體 中 文
DVP-PLC
(OPEN TYPE)
DVP-EC3
10 ~ 16
電 源 、 運 行 及 錯 誤 指 示 燈
輸 入 點 指 標
C O M 2
通 訊 口
( R S - 48 5 )
直 接 固 定 孔
+24V 24G S/ S X0 X1 X2 X3 X4 X5 X6 X7
D+ D- SG
CO M2
直 流 電 源 輸 出
輸 入 / 出 點 指 示 燈
POWER
RUN
ERROR
機 種 型 號
DVP1 6EC
8DI-DC / 8DO-R
CO M1
C O M 1
程 式 通 訊 口
交 流 電 源 輸 入
( RS - 2 32 C )
L
N
C0 Y0 Y1 Y2 Y3 C1 Y4 Y5
Y6 Y7
輸 出 點 指 標
D IN
軌 槽
( 3 5 mm )
D IN
軌 固 定 扣
直 接 固 定 孔
固 定 式 輸 出 / 端 子
+24V 24G S/S X0 X1 X2 X3 X4 X5 X6 X7
D+ D- SG
COM2
IN
0 1 2 3 4 5 6 7
PO WE R
RUN
OUT
0 1 2 3 4 5 6 7
E RRO R
90m m
99 m m
DVP16EC
8DI-DC / 8DO-R
COM1
A C 1 00 ~2 4 0V
I NP U T
L
N
C0 Y0 Y1 Y2 Y3 C1 Y4 Y5
Y6 Y7
9 0.5 m m
4 8.5 m m
95 m m
DVP10EC00 3
DVP14EC00 3
DVP16EC00 3
100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
95 ~ 100V AC
DVP-EC3
70V AC
DVP-EC3
10ms
2A/250V AC
9VA
100mA
DC24V
1,500V AC (Primary-secondary)
1,500V AC (Primary-PE)
500V AC (Secondary-PE)
5M
/
500V DC
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
RS: 26MHz ~ 1GHz, 10V/m
L, N
PLC
0° C ~ 55° C
50 ~ 95%
2
-25° C ~ 70° C
5 ~ 95%
IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
R 192g T 180g
R 202g T 185g
R 212g T 190g
SINK
SOURCE
24VDC 5mA
Off → On 15V DC
On → Off 5V DC
10ms
D1020
0 ~ 20ms
-R
-T
2A/1
5A/COM
0.5A/1
2A/COM
5~30VDC
250V AC, 30V DC
(UP, ZP
24V DC -15% ~ +20%
1mA/ )
75VA
15W/1
90W
10ms
Off → On 30us On → Off 100us

Advertisement

   Related Manuals for Delta Electronics Programmable Logic Controller DVP-EC3

   Summary of Contents for Delta Electronics Programmable Logic Controller DVP-EC3

  • Page 1

    ○ Flywheel diode: To extend the life span of contact 0° C ~ 55° C ○ Emergency stop: Uses external switch -25° C ~ 70° C Fuse: Uses 5 ~ 10A fuse at the shared terminal of ○ output contacts to protect the output circuit RS-485 ○...

  • Page 2

    安 裝 及 配 線 端 子 輸 入 ∕ 輸 出 配 置 DVP10EC00R3/T3 DC Signal IN SINK +24V +24V DVP10EC00R3 (6DI-DC / 4DO-R) D VP 10EC 00T3 (6DI-DC / 4D O-T) DVP14EC00R3/T3 +24V DVP14EC00R3 (8DI-DC / 6DO-R) +24V DC Signal IN DVP14EC00T3 (8DI- DC / 6DO-T) SOURCE...

This manual also for:

Dvp10ec00, Dvp14ec00, Dvp16ec00

Comments to this Manuals

Symbols: 0
Latest comments: