Panasonic MICRO-IMAGECHECKER A100 Series Hardware Manual
Hide thumbs Also See for MICRO-IMAGECHECKER A100 Series:
Table of Contents

Advertisement

Quick Links

Matsushita Electric Works ANM831
Double-Speed Random NAiS CCD Camera
A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
• C r i t i c a l a n d e x p e d i t e d s e r v i c e s
• I n s t o c k / R e a d y - t o - s h i p
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.
$
195
.00
In Stock
Qty Available: 1
New From Surplus Stock
Open Web Page
https://www.artisantg.com/46399-1
• We b u y y o u r e x c e s s , u n d e r u t i l i z e d , a n d i d l e e q u i p me n t
• F u l l - s e r v i c e , i n d e p e n d e n t r e p a i r c e n t e r

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MICRO-IMAGECHECKER A100 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Panasonic MICRO-IMAGECHECKER A100 Series

  • Page 1 Matsushita Electric Works ANM831 Double-Speed Random NAiS CCD Camera In Stock Qty Available: 1 New From Surplus Stock Open Web Page https://www.artisantg.com/46399-1 A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s . •...
  • Page 2 ® MICRO-IMAGECHECKER A200/A100 SERIES Hardware Manual POWER POWER ERROR ERROR READY READY KEYPAD KEYPAD TOOL TOOL MONITOR MONITOR CAMERA-A CAMERA-A CAMERA-B A200 Series A100 Series A200/A100 Series Hardware Manual ARCT1F425E ’06.9 Matsushita Electric Works, Ltd. http://www.nais-e.com/...
  • Page 3: Warnings And Cautions

    WARNINGS AND CAUTIONS To be observed at all times Read the manual carefully before installing, running, maintaining or inspecting the equipment. This manual uses two safety flags to indicate different levels of danger. WARNING: A handling error could cause serious physical injury to an operator, and in the worst case could even be fatal.
  • Page 4: General Instructions

    GENERAL INSTRUCTIONS Installation Environment Avoid using the Micro−Imagechecker A210/A110 in the following types of locations: − Locations with direct sunlight or environmental temperatures that exceed a range of 0°C to 50°C. − Locations with a relative humidity exceeding a range of 35%RH to 75%RH or that are subject to condensation due to dramatic temperature fluctuations.
  • Page 5: Other Instructions

    Before Switching On the Power The following points should be checked before switching the power on to the controller for the first time. − Check that no extra wiring left installation, especially conductive materials, have become attached to the board. −...
  • Page 7: Table Of Contents

    Contents Chapter 1 Part Names and Functions Controller ............1 −...
  • Page 8 Contents A200/A100 Hardware Chapter 4 Serial (RS−232C) Ports Serial (RS−232C) Ports ..........4 −...
  • Page 9 A200/A100 Hardware Contents Chapter 8 Part Numbers Controllers ............8 −...
  • Page 10 Contents A200/A100 Hardware...
  • Page 11: Part Names And Functions

    Chapter 1 Part Names and Functions Controller ........1 −...
  • Page 12 Part Names and Functions A200/A100 Hardware 1 − 2...
  • Page 13: Controller

    A200/A100 Hardware Part Names and Functions Controller Controller Weight: Around 300g A100 A200 Size: 40 × 120 × 50mm (Excluding protruding parts) Names and Functions of Controller Parts Operating LEDs Indicate the controller’s operating status. POWER (green) This green LED is lit when the controller is connected to a live power source.
  • Page 14 Part Names and Functions A200/A100 Hardware Controller Power supply 24 power is required. The power supply is connected to the input terminal block. External input terminal (16 pin) Provides a connection for input from an external source. External output terminal (16 pin) Provides a connection for output to an external device.
  • Page 15: A Series Camera

    A200/A100 Hardware Part Names and Functions A Series Camera A Series Camera 1.2.1 Double−Speed Random Camera Weight: around 70g (camera only) Size: 29 × 31 × 54.5mm (Excluding protruding parts) Names and Functions of Double−Speed Random Camera Parts Camera The camera body. Lens mount A C−mount.
  • Page 16 Part Names and Functions A200/A100 Hardware A Series Camera About the DIP Switches − Gain adjustment DIP switch 5: ON = 0 to +10dB range gain adjustment volume. OFF = 0dB − Potentiometer: When DIP−SW5 is ON, turning this potentiometer to the right increases the brightness of the image captured by the camera.
  • Page 17: Cs−Mount Camera

    A200/A100 Hardware Part Names and Functions A Series Camera 1.2.2 CS−Mount Camera CS−Mount Camera: Part Names and Functions 1. Camera The camera’s main unit. 2. Lens mount A CS−mount. 3. Lens Use the C/CS−mount lens together with an adapter ring as necessary. Select a lens from the Field of Vision and Lens Selection Table on page 2 −...
  • Page 18: Camera Cable And Camera Extension Cable

    Part Names and Functions A200/A100 Hardware Camera Cable and Camera Extension Cable Camera Cable and Camera Extension Cable Names and Functions of Parts 1. Connector (male): Connects the male connector to the controller. 2. Connector (female): Connects the female connector to the camera. Using the Cable Correctly −...
  • Page 19: Keypad

    A200/A100 Hardware Part Names and Functions Keypad Keypad 2, 3 ENTER Names and Functions of Parts 1. A, B, C buttons Can be operated using function displayed on the screen. 2. Cursor lever Moves the cursor. Can move it in a maximum of eight directions. 3.
  • Page 20 Part Names and Functions A200/A100 Hardware Keypad 1 − 10...
  • Page 21: Chapter 2 Installation And Wiring

    Chapter 2 Installation and Wiring Connecting Peripherals ......2− 3 Installation Environment and Mounting Space .
  • Page 22 Installation and Wiring A200/A100 Hardware 2 − 2...
  • Page 23: Connecting Peripherals

    A200/A100 Hardware Installation and Wiring Connecting Peripherals Connecting Peripherals Be sure to connect peripherals to the controller only when the controller power is OFF. Keypad Monitor−Cable 24 V DC Ground Camera−Cable *Only one camera can be connected to the A100. Using Peripherals Correctly −...
  • Page 24: Installation Environment And Mounting Space

    Installation and Wiring A200/A100 Hardware Installation Environment and Mounting Space Installation Environment and Mounting Space Avoid Installing the Equipment in Locations with the Following Characteristics − Where the temperature is outside the range of 0°C to 50°C. − Where the relative humidity is outside the range of 35%RH to 75%RH. −...
  • Page 25: Heat Dissipation

    A200/A100 Hardware Installation and Wiring Installation Environment and Mounting Space Heat Dissipation − Mount the unit in any of the following arrangements to facilitate heat dissipation. Contact mounting is acceptable. Do not mount the unit on top of strong heat sources such as heaters, transformers, or high−capacity resistors.
  • Page 26: Mounting The Controller

    Installation and Wiring A200/A100 Hardware Mounting the Controller Mounting the Controller You can mount the controller either by using screws or by hooking it on a DIN rail. Mounting the Controller on a DIN Rail The controller can be mounted on or removed from a 35mm wide DIN rail (DIN EN50022) by a single easy motion.
  • Page 27: Mounting The Camera

    A200/A100 Hardware Installation and Wiring Mounting the Camera Mounting the Camera Mount the camera so it doesn’t wobble. You can mount the camera directly or with metal fitting. Use the dimensional diagram for reference when you mount the camera. Using the Camera Correctly −...
  • Page 28: View Range And Lens Selection Tables

    Installation and Wiring A200/A100 Hardware View range and Lens Selection Tables View range and Lens Selection Tables Select the lens and extension rings from the following table in order to match the resolution or view range. 2.5.1 ANM831 Double−Speed Random Camera Lens ANB846NL ANB845NL...
  • Page 29: Anm832 Standard Camera

    A200/A100 Hardware Installation and Wiring View range and Lens Selection Tables 2.5.2 ANM832 Standard Camera Lens ANB846NL ANB845NL ANM8850 (1) ANB847L ANB843L Resolution (*1) ANM88251 ANM88161 f=50mm f=50mm f=8.5mm µm/pixel f=25mm f=16mm View range (mm) Vertical Horizontal view view Vertical Horizontal range range 10.4...
  • Page 30 Installation and Wiring A200/A100 Hardware View range and Lens Selection Tables Lens ANB842L ANM8808 (1) ANM8804 (1) ANM8828 (1) Resolution f=6.5mm f=8mm f=4mm f=2.8mm µm/pixel View range (mm) Vertical Horizontal view view Vertical Horizontal range range 10.4 10.4 15.6 15.6 10.7 20.8 20.9...
  • Page 31: Output Terminal (Parallel Output Port)

    Chapter 3 Input/Output Terminals (Input/Output Ports) Attaching Wires to the Terminal Blocks ... . . 3 − 3 Output Terminal (Parallel Output Port) ....3 −...
  • Page 32 Input/Output Terminals (Input/Output Ports) A200/A100 Hardware 3 − 2...
  • Page 33: Attaching Wires To The Terminal Blocks

    A200/A100 Hardware Input/Output Terminals (Input/Output Ports) Attaching Wires to the Terminal Blocks Attaching Wires to the Terminal Blocks Output terminal block Input and power terminal block Body Terminal block Cable About Terminal Blocks The I/O terminal block (Matsushita Denkou part number: ANMA8001, Phoenix part number: 1840502) plugs into the controller, and the terminals are fastened by tightening the screws.
  • Page 34: Output Terminal (Parallel Output Port)

    Input/Output Terminals (Input/Output Ports) A200/A100 Hardware Output Terminal (Parallel Output Port) Output Terminal (Parallel Output Port) Terminal Positions Signal Name Content COMMON Common flash dedicated line FLASH Flash sync signal COMMON General output common READY Ready signal ERROR Error signal READ END Image capture complete signal STROB...
  • Page 35: Input Terminal (Parallel Input Port)

    A200/A100 Hardware Input/Output Terminals (Input/Output Ports) Input Terminal (Parallel Input Port) Input Terminal (Parallel Input Port) Terminal Positions Signal Name Content COMMON START common START Inspection start signal COMMON COMMON, other than START input ACKNOWLEDGE Data receiving complete signal TYPE Product type switched signal Data input Data input...
  • Page 36: Cautions Related To Parallel Input/Output

    Input/Output Terminals (Input/Output Ports) A200/A100 Hardware Cautions Related to Parallel Input/Output Cautions Related to Parallel Input/Output The input/output ports are housed in the particular controller being used. The ports differ according to the inspection specifications. See the individual controller’s user manual for details.
  • Page 37: About Parallel Input

    A200/A100 Hardware Input/Output Terminals (Input/Output Ports) Cautions Related to Parallel Input/Output 3.4.2 About Parallel Input − The controller accepts ( ) common. To prevent input signal chattering, use a ± non−contact input (transistor etc.). If chattering occurs, inputs can be missed, and input recognition delayed.
  • Page 38: Flash Output Sync Signal

    Input/Output Terminals (Input/Output Ports) A200/A100 Hardware Flash Output Sync Signal Flash Output Sync Signal Terminal Positions COM: The flash terminal is located in the output terminal. FLASH FLASH: The common terminal for use by the flash is a specialized terminal. Do not use it together with other common lines.
  • Page 39 A200/A100 Hardware Input/Output Terminals (Input/Output Ports) Flash Output Sync Signal Using the Flash Output Sync Signal Correctly − The flash’s common wire uses a specialized terminal. Do not use it together with another common wire. − You cannot use the same strobe for multiple cameras connected to separate controllers.
  • Page 40: Electric Power Wiring

    Input/Output Terminals (Input/Output Ports) A200/A100 Hardware Electric Power Wiring Electric Power Wiring Terminal Positions 24 V DC electric power is supplied by attach- ing wires to the input terminal block’s (+) and (–) terminals and to the ground terminal (frame ground).
  • Page 41 A200/A100 Hardware Input/Output Terminals (Input/Output Ports) Electric Power Wiring Increase Resistance to Noise − Separate the systems for wiring to the controller, input devices, and output devices. − When there is a particular concern about noise coming from input/output circuits, supply power to the controller and to the input/output devices separately.
  • Page 42: About Grounding

    Input/Output Terminals (Input/Output Ports) A200/A100 Hardware About Grounding About Grounding Attaching a Ground to Prevent Effects of Noise − The controller can tolerate the noise present in a normal environment. Provide a ground when installing it in a particularly noisy environment. Use a Dedicated Ground Wire −...
  • Page 43: Chapter 4 Serial (Rs−232C) Ports

    Chapter 4 Serial (RS−232C) Ports Serial (RS−232C) Ports ......4− 3 COM port (Data output, VBT Ver. 2) .
  • Page 44 Serial (RS−232C) Ports A200/A100 Hardware 4 − 2...
  • Page 45 A200/A100 Hardware Serial (RS−232C) Ports Serial (RS−232C) Ports Serial (RS−232C) Ports The controller contains two independent serial ports. The COM port is an 8−pin round connector. It is used for general RS−232C communication. The TOOL port is a square connector. It is used only for connection to VBT Ver. 2. An application stored in the controller determines the commands and parameters such as baud rate and parity used for communication.
  • Page 46 Serial (RS−232C) Ports A200/A100 Hardware Serial (RS−232C) Ports Examples of RS−232C Connections General−purpose RS−232C and VBT Ver. 2 can be used for the COM port. Only VBT Ver. 2 can be used for the TOOL port. TOOL TOOL Cannot connect For saving and restoring VBT Ver.
  • Page 47 A200/A100 Hardware Serial (RS−232C) Ports COM port (Data output, VBT Ver. 2) COM port (Data output, VBT Ver. 2) Terminal Positions A Hoshiden−manufactured connector (part no. TCS6180) is used as the COM (RS−232C) port on the controller unit. Controller−side terminal Pin No.
  • Page 48 Serial (RS−232C) Ports A200/A100 Hardware COM port (Data output, VBT Ver. 2) −Connection with PLC Please make the connection using the ANM81303 RS232C cable (see below) according to the following wiring example. Since the wires on the PLC side of the RS232C cable are loose, please prepare them in accordance with the PLC you will be using.
  • Page 49 A200/A100 Hardware Serial (RS−232C) Ports COM port (Data output, VBT Ver. 2) Example of connection with Mitsubishi PLC Computer Link Communication with Mitsubishi A/Q series supports for “Type 4”. Example 1 Mitsubishi A & Q series(9pins) ICH A series Signal Wire Signal White...
  • Page 50 Serial (RS−232C) Ports A200/A100 Hardware COM port (Data output, VBT Ver. 2) Example of connection with Omron PLC Omron: C series Ex. 1 (9 pin) ICHA series Signal Wire Signal color White Black Short Short Yellow Blue – Short – Green –...
  • Page 51 A200/A100 Hardware Serial (RS−232C) Ports COM port (Data output, VBT Ver. 2) Example of connection with Allen−Bradley PLC Allen−Bradley: SLC500 ICH A series Signal Wire Signal color White Black Short Yellow Blue Short Green Brown Gray − Cover Shield Cover Shield –...
  • Page 52: Tool Port (Vbt Ver. 2 Port)

    Serial (RS−232C) Ports A200/A100 Hardware TOOL port (VBT Ver. 2 Port) TOOL port (VBT Ver. 2 Port) Terminal Positions A Hoshiden−manufactured connector (part no. TCS7729) is used as the TOOL port on the controller unit. Controller−sideterminals Pin No. Signal Name Pin No.
  • Page 53 A200/A100 Hardware Serial (RS−232C) Ports TOOL port (VBT Ver. 2 Port) 9pin 9pin 9pin male female female TOOL port ANM8121001 Commercially available cross cable Commercially available ANM812001 cross cable Hoshiden D−Sub 9pin male terminal D−Sub 9pin female terminal D−Sub 9pin female terminal TCP8951 Reserved R×D...
  • Page 54 Serial (RS−232C) Ports A200/A100 Hardware TOOL port (VBT Ver. 2 Port) 4 − 12...
  • Page 55: About Camera Modes

    Chapter 5 About Camera Modes Camera Modes ....... . . 5 −...
  • Page 56 About Camera Modes A200/A100 Hardware 5 − 2...
  • Page 57: Camera Modes

    A200/A100 Hardware About Camera Modes Camera Modes Camera Modes Two of our cameras can be used with the A Series: The double−speed random camera, model ANM831, and the standard camera, model ANM832. The A Series supports a total of six camera modes. The camera mode is set according to whether the inspection object is moving or still, whether the illumination is continuous or strobe, and the camera type.
  • Page 58: Imaging Time For The Camera Modes (For Memory Image Display) And Resolution

    About Camera Modes A200/A100 Hardware Imaging Time for the Camera Modes (for memory image display) and Resolution Imaging Time for the Camera Modes (for memory image display) and Resolution Frame Field Double−Speed Imaging time = (shutter time) + 16.7ms Imaging time = (shutter time) + 8.3ms Ra do Random Start Trigger...
  • Page 59: Frame Mode And Field Mode

    A200/A100 Hardware About Camera Modes Frame Mode and Field Mode Frame Mode and Field Mode Frame Mode In this mode, the camera captures an even number array and an odd number array and sends them to the image processing system. In the A Series, all 512 × 480 pixels are sent to memory and are then subject to image processing.
  • Page 60 About Camera Modes A200/A100 Hardware Frame Mode and Field Mode 5 − 6...
  • Page 61 Chapter 6 Product Type Data Creation and Backup Product Type Data Creation and Backup ... 6− 3...
  • Page 62 Optional Memory A200/A100 Hardware 6 − 2...
  • Page 63: Chapter 6 Product Type Data Creation And Backup

    A200/A100 Hardware Optional Memory Product Type Data Creation and Backup Product Type Data Creation and Backup Product type data is created with the special−purpose keypad. You can back up the created product type data together with image data stored on the controller to a *Windows PC, then restore the data later.
  • Page 64 Optional Memory A200/A100 Hardware Product Type Data Creation and Backup 6 − 4...
  • Page 65: Chapter 7 General Specifications

    Chapter 7 General Specifications Controller ........7 −...
  • Page 66 General Specifications A200/A100 Hardware 7 − 2...
  • Page 67: Controller

    A200/A100 Hardware General Specifications Controller Controller Item Specification 512 × 480 pixels (horizontal × vertical) Processing resolution Processing function Gray scale image/binarized image processing (details are determined by the application) Settings Special−purpose keypad External interface Serial COM port: RS−232C TOOL port: RS−232C Parallel input Removable terminal block Input to 11 positions 12 V to 24 V DC input Bidirectional photocoupler...
  • Page 68: Keypad

    General Specifications A200/A100 Hardware Keypad Keypad Item Specification Operation bottuns, lever 8−direction lever, used jointly with the ENTER button: 1. A, B, C buttons = 1 each Operating / storage ambient humidity ° RH 35% to 75% (without icing and dew condensation at 25 Operating ambient temperature °...
  • Page 69 A200/A100 Hardware General Specifications Monitor: ANMA810 Monitor: ANMA810 Item Specification Rated voltage 100 V AC Allowable voltage range 90 to 120 V AC Rated power consumption 30 W or less 9 inch, White Operation frequency Horizontal: 15.734 kHz Vertical: 59.94 Hz Input level 1.0 Vp−p (Video signal: 0.7 Vp−p positive polarity Synchronization signal: negative polarity)
  • Page 70: Double−Speed Random Camera Anm831

    General Specifications A200/A100 Hardware Double−Speed Random Camera ANM831 Double−Speed Random Camera ANM831 Item Specification Imaging element Readout of all pixels (interline transfer protocol) 1/3 inch CCD fixed photo elements Horizontal 659 pixels × vertical 494 pixels; pixel size = Square Pixel Effective pixels Scanning method Non−interlaced mode (1/60s)
  • Page 71: Cs−Mount Camera Anm832

    A200/A100 Hardware General Specifications CS−Mount Camera ANM832 CS−Mount Camera ANM832 Item Specification Imaging element Interline transmission method 1/3 inch CCD solid state imaging element 768 pixels (horizontal) × 492 pixels (vertical) Effective pixels Scanning method 2:1 interlace (1/60s) Accumulation Frame accumulation Shutter speed OFF 1/60s, Electronic shutter = 1/100, 1/125, 1/500, 1/1000, 1/2000, 1/4000, and...
  • Page 72 General Specifications A200/A100 Hardware CS−Mount Camera ANM832 7 − 8...
  • Page 73: Part Numbers

    Chapter 8 Part Numbers Controllers ........8 −...
  • Page 74 Part Numbers A200/A100 Hardware 8 − 2...
  • Page 75 A200/A100 Hardware Part Numbers Controllers Controllers Item Specification Part Number Micro−Imagechecker A200 series Multichecker NPN Output Conformed ANMA210 Initial display : Japanese Includes Japanese manual NPN Output Conformed ANMA212 Initial display : English Includes English manual Photo MOS Output Conformed ANMA218 Initial display : English Includes English manual...
  • Page 76 Part Numbers A200/A100 Hardware Controllers Item Specification Part Number Micro−Imagechecker A100 series Multichecker NPN Output Conformed ANMA110 Initial display : Japanese Includes Japanese manual NPN Output Conformed ANMA112 Initial display : English Includes English manual Photo MOS Output Conformed ANMA113 Initial display : English No manual Spare Input/Output Terminal...
  • Page 77: Cameras

    A200/A100 Hardware Part Numbers Cameras Cameras Item Specification Part Number Double−speed random camera Double−speed random camera Conformed ANM831 CS−mount camera CS−mount camera Not conformed ANM832 ANM83203 Conformed ANM832CE *1) Although ANM83203 is the same specification as ANM832, only the length of a cable has a difference in both.
  • Page 78: Double−Speed Random Camera Cable

    Part Numbers A200/A100 Hardware Double−Speed Random Camera Cable Double−Speed Random Camera Cable Item Specification Part Number ANM831 camera cable Not conformed ANM84303 3m: CE compliant Conformed ANM84303CE 3m: Anti−bending camera cable Not conformed ANM84603 Use the camera extension cable when extending the double−speed random camera’s cable 3 meters or more.
  • Page 79: Camera Extension Cable

    A200/A100 Hardware Part Numbers Camera Extension Cable Camera Extension Cable Item Specification Part Number Extension cable for Extension cable = 2m: total 5m Not conformed ANM84002A ANM831/ANM832 (CE) ANM831/ANM832 (CE) Extension cable = 7m: total 10m Not conformed ANM84007A Extension cable = 12m: total 15m Not conformed ANM84012A Extension cable = 17m: total 20m...
  • Page 80 Part Numbers A200/A100 Hardware Keypad Keypad Item Specification Part Number Keypad for A/M series Cable length = 2m Not conformed ANM85202 Cable length = 3m Not conformed ANM85203 Cable length = 5m Not conformed ANM85205 Cable length = 10m Not conformed ANM85210 Cable length = 2m: CE Conformed...
  • Page 81: Monitor

    A200/A100 Hardware Part Numbers Monitor Monitor Item Specification Part Number Monitor Power code (length: 1.5m), Monitor cable (length: 3m) Not conformed AMMA810 and BNC connector provided Monitor cable Cable length: 3m ANM87303 (PIN BNC) (PIN−BNC) Cable length: 5m ANM87305 Cable length: 10m ANM87310 Cable length: 15m ANM87315...
  • Page 82: Data Backup Software And Pc Cable

    Part Numbers A200/A100 Hardware Data Backup Software and PC Cable Data Backup Software and PC Cable Item Specification Part Number Data backup software* Vision Backup Tool Version 2 (for A/M series) ANM7013V2 Supports Japanese language, runs under Windows. Vision Backup Tool Version 2 (for A/M series) ANM70131V2 Supports English, runs under Windows.
  • Page 83: Lenses And Adapter Rings

    A200/A100 Hardware Part Numbers Lenses and Adapter Rings Lenses and Adapter Rings Item Specification Specification Part Number C Mount Lenses f6.5 lens − − − − − ANB842L f8.5 lens With lock ANB843L f16 lens With lock ANB845NL ANB88161 f25 lens With lock ANB846NL ANB88251...
  • Page 84 Part Numbers A200/A100 Hardware Lighting for Image Processing Lighting for Image Processing Item Specification Part Number Ring light outside diameter: Φ 50, red AULDR2−50RD [Direct lighting] li h i outside diameter: Φ 50, white AULDR2−50RD−SW outside diameter: Φ 70, red AULDR2−70RD outside diameter: Φ...
  • Page 85: Dimension Diagram

    Chapter 9 Dimension diagram Controller ........9 −...
  • Page 86 Dimension diagram A200/A100 Hardware 9 − 2...
  • Page 87: Controller

    A200/A100 Hardware Dimension diagram Controller Controller (9.5) (5.5) 9 − 3...
  • Page 88: Double−Speed Random Camera Anm831

    Dimension diagram A200/A100 Hardware Camera Camera 9.2.1 Double−Speed Random Camera ANM831 54.5 46.5 24.5 1/4−20UNC 4−M3 (depth 2.5mm) 2−M3 (depth 4mm) (depth 9mm) 3.25 9.2.2 CS−Mount Camera ANM832 49.5 (43) 49.5 3000 (43) −10 24.5±0.2 4−M3 (depth 2.5mm) 24.5±0.2 14 2−M3 (depth 7mm) 4−M3(深さ...
  • Page 89: Camera Cable And Camera Extension Cable

    A200/A100 Hardware Dimension diagram Camera Cable and Camera Extension Cable Camera Cable and Camera Extension Cable *B is the length of the installed cable. Unit : mm The length of a cable with CE is short a little. 9 − 5...
  • Page 90: Keypad

    Dimension diagram A200/A100 Hardware Keypad Keypad 54.4 A: Depends on the installed keypad. The length of a cable with CE is short a little. Unit : mm 9 − 6...
  • Page 91: Monitor: Anma810

    A200/A100 Hardware Dimension diagram Monitor: ANMA810 Monitor: ANMA810 Around 80mm or more including the cable connection (20) (68) 144.5 4−M3 CAUTION LABEL Unit : mm Note Reserve at least 80mm of space to the rear of the monitor to facilitate wiring and heat dissipation. Input/output to the monitor is with a BNC terminal.
  • Page 92 Dimension diagram A200/A100 Hardware Lenses Lenses C mount lenses Filter size ANB842L f=6.5 − φ48 ANB843L f=8.5 M40.5 φ42 ANB845NL f=16 φ30 ANB846NL f=25 37.3 φ30 Locking screws (only on lenses with lock) ANB88161 f=16 M25.5 φ30.5 ANB88251 f=25 25.5 M25.5 φ30.5 ANB847L...
  • Page 93 A200/A100 Hardware Dimension diagram Lenses Dimensions ANM8850 38.5 M25.5×0.5 1−32 UNF CS−MOUNT ANM88501 38.5 19.3 M25.5×0.5 1−32 UNF CS−MOUNT ANM8808 1−32 UNF CS−MOUNT M30.5×0.5 9 − 9...
  • Page 94 Dimension diagram A200/A100 Hardware Lenses ANM88081 M25.5×0.5 1−32 UNF CS−MOUNT 11.5 ANM8804 M30.5×0.5 1−32 UNF CS−MOUNT ANM88041 1−32 UNF CS−MOUNT M25.5×0.5 11.5 9 − 10...
  • Page 95 A200/A100 Hardware Dimension diagram Lenses ANM8828 1−32 UNF CS−MOUNT ANM88281 37.5 1−32 UNF CS−MOUNT 11.5 9 − 11...
  • Page 96 Dimension diagram A200/A100 Hardware Lenses 9 − 12...
  • Page 97: Pin Assignment

    Chapter 10 Pin Assignment 10.1 Camera Pin Positions (ANM831) ....10− 3 10.2 Camera Pin Positions (ANM832) ....10−...
  • Page 98 Pin Assignment A200/A100 Hardware 10 − 2...
  • Page 99: Camera Pin Positions (Anm831)

    A200/A100 Hardware Pin Assignment 10.1 Camera Pin Positions (ANM831) 10.1 Camera Pin Positions (ANM831) Micro−Imagechecker Camera ANM831 HR10A−10P−12P HR10A−10P−12S (Hirose) (Hirose) View direction View direction ANM843** HR10A−10R−12P HR10A−10R−12S (Hirose) (Hirose) CAMERA−A Female Male Female Male Signal Name Signal Name Signal Name Signal Name POWER GND SHT3...
  • Page 100: Camera Pin Positions (Anm832)

    Pin Assignment A200/A100 Hardware 10.2 Camera Pin Positions (ANM832) 10.2 Camera Pin Positions (ANM832) Micro−Imagechecker Camera ANM832 HR10A−10P−12P(Hirose) View direction HR10A−10R−12S (Hirose) CAMERA−A Signal Name Green +12V POWER GND VIDEO Female Male Brown Video shield Orange HD shield Signal Name Signal Name Yellow POWER GND...
  • Page 101: Chapter 11 Manual Revision History

    Chapter 11 Manual revision history 11.1 Manual revision history ......11− 3...
  • Page 102 Manual revision history A200/A100 Hardware 11 − 2...
  • Page 103: Manual Revision History

    Added content −Anti−bending camera cables −Filter size for lens ARCT1F425E Aug. 2006 First edition − Revision associated with a change of the brand (NAiS to Panasonic). − Corrections of errors in writing. − Addition of descriptions about grounding. 11 − 3...
  • Page 104 Manual revision history A200/A100 Hardware 11 − 4...

This manual is also suitable for:

Micro-imagechecker a200 seriesMicro-imagechecker anm831Micro-imagechecker anm832

Table of Contents