Related Manuals for Werner MULTI-POSITION PRO 14ft
Summary of Contents for Werner MULTI-POSITION PRO 14ft
- Page 1 375lb LOAD CAPACITY MULTI-POSITION PRO with POWERLITE® RAILS Operating Procedure and Safety Instructions 22 ft. Model 14 ft. Model...
- Page 2 MULTI-POSITION PRO with POWERLITE ® RAILS Operating Procedure and Safety Instructions WARNING: 1. Read these instructions completely before using the ladder. If you don’t under- stand call 1-888-523-3371 for assistance. 2. Failure to comply with all instructions may result in serious injury. 1 DESCRIPTION •...
- Page 3 DESCRIPTION PRODUCT OVERVIEW WARNING The Telescoping Use ladder only in positions as shown Multiladder is a below. Any other position is misuse professional grade, of the product which could result in multi-purpose ladder serious injury or death. that can be changed into different positions CAUTION and working heights.
- Page 4 WORKING HEIGHTS The following chart shows the working heights of each of the available units in each of the five main positions. 14ft MODEL 18ft MODEL 22ft MODEL 26ft MODEL Step* 9ft 4in 11ft 4in 13ft 2in 15ft 1in Extension* 14ft 3in 18ft 1in 22ft 0in...
- Page 5 Greenville, PA 16125-9499 or alkalis). 1-888-523-3371 • For information on replacing parts or labels contact Werner Co. at the address given. If possible, know model number of ladder for reference. See I.D. label on product. PROPER SET-UP AND USE For safety, follow these set-up and use instructions: •...
- Page 6 (Refer to labels on ladder.) • DO NOT use any components not supplied or approved by Werner Co. with this ladder. DANGER • To set ladder up: Support ladder by laying it on its side on the ground. Open to desired allowable position and then stand ladder up.
- Page 7 PUSH KNOB LOCKING HINGE HINGE OPERATION For safety, follow these push knob hinge instructions: The ladder's inner section allows the ladder to be folded into 3 set positions; extension ladder, twin stepladder, and storage. Each of these configurations is made possible by using the push knob locking hinge located on each side of the ladder.
-
Page 8: Lock Operation
SPRING LOADED “J” LOCKS LOCK OPERATION For safety, follow these Spring Loaded “J” Locks instructions: The ladder's outer sections allow the ladder to telescope and change heights in all the configurations, besides the scaffold mode. Each of these configurations is made possible using the 4 Spring Loaded “J”... - Page 9 PROPER USE HOW TO SETUP POSITIONS The Telescoping Multiladder can be used in positions shown below with no additional equipment required. The following instruction will demonstrate how to change the Telescoping Multiladder. Position #1 Twin Stepladder 1) To configure the ladder into the stepladder position, follow the directions for changing the angle of the ladder (Section 3) using the push knob locking hinge.
- Page 10 Position #2 Stairway Stepladder 1) To configure the ladder into the Stairway Stepladder position (this position is used when the user needs to work in a stairway.), configure the ladder in the stepladder configuration as described in position #1. Raise to desired height. 2) Lower one side of the inner section until the desired step height is reached.
- Page 11 PROPER USE HOW TO SETUP POSITIONS (continued) Position #3 Extension Ladder Note: The extension ladder position is 75° easiest completed with the ladder laying on the ground. Approximately 1) Configuring the ladder into the extension ladder position, as with the stepladder position, the extension ladder position starts with changing the angle.
- Page 12 Position #4 2-Scaffold Bases 1) Separate the inner and outer sections completely by unlocking the “J” locks and sliding the outer sections off the inner section. 2) Place inner section in stepladder position. This is the first of two trestles required for the scaffold position.
- Page 13 Position #5 Wall Ladder 1) To configure the ladder into the Wall Ladder position, configure the ladder in the stepladder configuration as described in position #1. Raise to desired height. 2) Lower one side of the inner section one rung. 3) Never use in this position free standing.
- Page 14 PROPER USE HOW TO SET UP THE LEVELER The built-in leveling system allows the length of the right and left legs to be adjusted when setting up the ladder on uneven surfaces. Each leg extends up to 7”. To adjust the leveler: 1) Using your foot, push down on the tab located on the front feet until the ladder is leveled.
-
Page 15: Accessories Available
To order accessories below contact your local Werner distributor. AC18MT AC24 AC96 Platform Project Stabilizer Tray (Platform rated to 300 lbs.) WERNER CO. 555 PIERCE RD, STE 300, ITASCA, IL 60143 Phone: 1-888-523-3371 www.wernerladder.com P/N117615-03 © 2024 Werner Co. Rev B...
Need help?
Do you have a question about the MULTI-POSITION PRO 14ft and is the answer not in the manual?
Questions and answers