Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Maytag Jade Dynasty RJGR4873C
Summary of Contents for Maytag Jade Dynasty RJGR4873C
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Jade Dynasty RJGR4873C Owner's Manual Shop genuine replacement parts for Jade Dynasty RJGR4873C Find Your Jade Dynasty Gas Range Parts - Select From 23 Models -------- Manual continues below --------...
- Page 2 Service This manual is to be used by qualified appliance technicians only. Maytag does not assume any responsibility for property damage or personal injury for improper service procedures done by an unqualified person. Freestanding This Base Manual covers general information...
-
Page 3: Important Information
Important Notices for Servicers and Consumers Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service. -
Page 4: Table Of Contents
Bake or Broil Ignitors ..........10 Front Facade ............19 Gas Valve .............. 10 Module Type ............19 Surface Burners, Griddle, Charbroil ....... 10 Spark System ............10 Troubleshooting Procedures ......... 11 - 12 Component Testing Procedures ......13 - 14 16023219 ©2004 Maytag Services... -
Page 5: Safety Information
14 inches W.C.P. To avoid risk of electrical shock, property damage, personal injury or death; verify wiring is correct, if components were replaced. Verify proper and complete operation of unit after servicing. 16023219 ©2004 Maytag Services... -
Page 6: Safety Practices For Servicer
National Electrical Code. Do not use an extension cord with this appliance. • Insure all packing materials are removed from the range before operating it, to prevent fire or smoke damage should the packing material ignite. 16023219 ©2004 Maytag Services... -
Page 7: Delayed Ignition
Flammable material could ignite if brought in contact with flame or hot oven surfaces which may cause severe burns. • Never use range for warming or heating a room. This 16023219 ©2004 Maytag Services... -
Page 8: Connecting Range To Gas
CONNECTION may be made to properly grounded two- prong wall receptacle by the use of a UL listed adapter available at most hardware stores. Larger slot on adapter must be aligned with larger slot in the wall receptacle to provide proper polarity. 16023219 ©2004 Maytag Services... -
Page 9: Product Safety Devices
If any ground wire, screw, strap, nut, etc. is removed for service, or any reason, it must be reconnected to its original position with original fastener before the appliance is put into operation again. Failure to do so can create a possible shock hazard. 16023219 ©2004 Maytag Services... -
Page 10: General Information
Stainless Steel Body Accent Option (front & Sides GT – Gold Trim If not unit will be trimmed in Stainless and Chrome. Gas Type LP – Liquid Propane If not unit will be set for Natural Gas 16023219 ©2004 Maytag Services... -
Page 11: Model Identification
Ignitors glow anytime bake or broil burners are operating and cycle on and off with the thermostat cycling contacts. 16023219 ©2004 Maytag Services... -
Page 12: Troubleshooting Procedures
Unit continues to spark after advised. knob is turned to OFF • Carefully reposition switch on Switch has slipped off the valve ....position. valve and rotate from OFF to high, several times to verify switch is not broken. 16023219 ©2004 Maytag Services... - Page 13 Fan motor does not operate. next step. Failed fan motor or winding or frozen shaft. • Check motor winding for continuity. Check for a frozen motor shaft. Check for broken wiring between motor and neutral terminal block. 16023219 ©2004 Maytag Services...
-
Page 14: Component Testing Procedures
Verify gas pressure (WCP). Natural " LP/Propane " Check orifice for debris. Clean as needed. Spark ignition Test for resistance of spark lead ..Continuity electrode Test ignitor to chassis ......No continuity from ignitor to chassis. 16023219 ©2004 Maytag Services... - Page 15 Test for continuity at wire terminals. Switch in LITE position....... Continuity Switch in any other position ....Infinite Top surface burner Verify gas is supplied ......Check for obstructions in burner ports. Verify burner cap is positioned correctly. 16023219 ©2004 Maytag Services...
-
Page 16: Disassembly Procedures
NOTE: Perform gas leak test to ensure unit will not leak switches. and unit operates properly. 7. Slide indicator lights to the side to release from holders. NOTE: Once an indicator light is released from the holder the front lens will fall out. 16023219 ©2004 Maytag Services... -
Page 17: Spark Module
9. Replace component and reverse procedure to light socket. reassemble. 5. Release metal tabs on light socket and allow light socket to release into the oven cavity area. 6. Replace component and reverse prodceure to assemble. 16023219 ©2004 Maytag Services... -
Page 18: Broil Burner And Ignitor
5. Disconnect gas lines connected to gas valve. 6. Remove screws securing gas valve bracket to unit chassis. 7. Replace component and reverse procedure to reassemble. NOTE: Perform gas leak test to ensure unit will not leak and unit operates properly. 16023219 ©2004 Maytag Services... -
Page 19: Door Removal
8. remove nuts securing inner door wrapper to inner door. 9. Remove insulation to gain access to inner window assembly. 10.Remove nuts securing inner window assembly and replace if necessary. 11. Replace component and reverse procedures to reassemble. 16023219 ©2004 Maytag Services... -
Page 20: Front Facade
1. Turn off gas and power supply to the oven. 2. Remove griddle from module. 3. Remove screws securing ignitor to module. 4. Remove screw securing burner to module. 5. Remove burner from module. 6. Replace component and reverse procedure to reassemble. 16023219 ©2004 Maytag Services... - Page 21 Disassembly Procedures To avoid the risk of electrical shock, personal injury or WARNING death; disconnect power to oven and shut off gas supply before following any disassembly procedure. This page is intentionally left blank. 16023219 ©2004 Maytag Services...
Need help?
Do you have a question about the Jade Dynasty RJGR4873C and is the answer not in the manual?
Questions and answers