Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Besantek BST-DL09
Summary of Contents for Besantek BST-DL09
- Page 1 BST-DL09 Single-Use USB PDF Temperature and Humidity DataLogger Manual V1.0...
-
Page 2: Table Of Contents
Content Chapter I: Product introduction ............... 1 1.1Product introduction ......................... 1 1.2 Application ..........................1 1.3Prod uct Feature........................1 1.4Performance Parameters ......................2 Chapter II: Instruction Manual ................. 3 2.1Instrument appearance specification ..................3 2.2 Instrument instructions ......................4 2.3PDF document description ..................... 7 Chapter III: Precautions .................. -
Page 3: Chapter I: Product Introduction
Chapter I Product Introduction 1.1Product Introduction This product carries a new type of microcontroller, one-time record. Ability to generate PDF documents on their own, the user can access a variety of devices, easy to quickly browse recorded temperature and humidity data. Instrument equipped with a small LCD display, temperature and humidity at the same time display, user-friendly browsing to real-time temperature and humidity information, display data can be accurate to one decimal places, and eye-catching battery tips, always remind the electricity situation. -
Page 4: Performance Parameters
1.4Performance Parameters Parameters Parameter index Parameters Parameter index Temperature 1/2AA 3.6V Lithium Voltage measuring -30~70 ℃ battery range Temperature Working -30~70℃ measuring ±0.5 ℃ Temperature accuracy Relative humidity Size 125*28*22mm 0~100% RH measuring range Relative humidity Weight ±5% RH measuring accuracy Measuring Interval... -
Page 5: Chapter Ii Instruction Manual
Chapter II Instruction Manual 2.1Instrument appearance instructions Figure 2-1 Front appearance diagram 1﹣OK button：Instrument shutdown state, connected to PC set synchronize and time, long press this button for 3 seconds, the instrument boot and automatically enter the calibration mode, press this button again equipment shut down, turned off after press this button switch on the instrument into the recording mode. -
Page 6: Instrument Instructions
When the instrument is turned on, press (short press) this button, the LCD will switch the display (real-time data, minimum value MIN, maximum value MAX, alarm lower limit LO, alarm upper limit HI cycle switching). Instrument boot record state, long press this button for 3 seconds, the instrument off. 2﹣Humidity light：The instrument records and humidity over limit state, the light once every 10 seconds, indicating that the humidity is exceeding limits. - Page 7 Figure 2-3DataLogger software interface 1. The serial number of the instrument: corresponding to the series number of label on the back of the instrument. 2. The program version of the instrument. 3. Temperature alarm upper and lower limit setting: the temperature measured by the instrument is not in the range of the setting upper and lower limit, instrument will be alarming state.
- Page 8 2.Instrument boot, enter calibration mode: After synchronizing time, the instrument is pulled out from the computer, press the OK button to power on, the instrument enters the calibration mode, normal display real-time temperature and humidity, can check the maximal value, minimum value , alarm lower limit and alarm upper limit, Does not display temperature and humidity units, does not generate PFD documents.
-
Page 9: Pdf Document Description
re-record after synchronized instrument setting, but can be connected to the computer to view and save the data. 2.3 PDF document description 1.PDF generation: After the instrument is connected to a computer, the PDF document will be generated. At this time, the temperature light will flash and the representative is generating PDF. - Page 10 Figure 2-6 PDF Document Page 1 1）Instrument serial number 2）Over limit alarm prompt: blank = no alarm, red = alarm. 3）Set the recording interval, unit: second 4）Instrument recording start and end time...
- Page 11 5）Total number of data recorded 6）Record the total length of time 7) The maximum, minimum and average temperature and humidity recorded by the instrument. 8）Set the lower limit of temperature and humidity 9）Temperature and humidity exceed the minimum number of limits set 10）Set the upper limit of temperature and humidity 11）The first excess lower limit and the last excess lower limit time 12）Excess the Min value in over limit state: No over limit record display OK, there is over...
-
Page 12: Chapter Iii Precautions
Chapter III Precautions 1. The PDF generation will take a certain amount of time. During this time, the instrument will not be pulled out from the port, otherwise the data will be lost. 2. After the instrument is connected to the computer, the instrument will be automatically ended the recording function and shutdown.
Need help?
Do you have a question about the BST-DL09 and is the answer not in the manual?
Questions and answers