Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for White Rodgers Electro-Air SST 10C26S-010
Summary of Contents for White Rodgers Electro-Air SST 10C26S-010
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. WHITE RODGERS SST16C28S-010 Owner's Manual Shop genuine replacement parts for WHITE RODGERS SST16C28S-010 Find Your WHITE RODGERS Air Cleaner Parts - Select From 61 Models -------- Manual continues below --------...
- Page 2 by White-Rodgers Electronic Air Cleaner Super Slim Twin DG ERS WH ITE -RO Model Number 10C26S-010 14C26S-010 16C28S-010 20C26S-010 OWNERS MANUAL Installation • Operation • Basic SST Service Guide • Technical Repair Guide • Repair Parts • Please read and familiarize yourself with the contents of this manual before installing, operating or performing maintenance on the unit.
-
Page 3: Table Of Contents
1. Read the Owners Manual and the Rules for Safe RULES FOR SAFE Operation carefully. Failure to follow these rules and INSTALLATION instructions could cause a malfunction of filter or unsatisfactory service. AND OPERATION 2. Follow a regular service and maintenance schedule for efficient operation. -
Page 4: How The Air Cleaner Works
HOW THE AIR CLEANER WORKS Dirt particles flowing through the ducts (Figure 1) first enters the pre-filters (A) where large particles (hair, lint, Dirty Air In Clean Air Out etc.) are trapped. Smaller particles (smoke, dust, pollen, etc.) pass through these pre-filters and enter the ionizing section (B). -
Page 5: Preinstallation
PREINSTALLATION Not to Exceed 20° (Interchangeable) (Interchangeable) Collecting Cell Air Flow Collecting Cell Outlet Box Cabinet Power Pack Handle Air Flow Furnace Opening Electronic Air Cleaner Contact Opening Button Contact Furnace Electronic Pre-Filters Button Transition Section Air Cleaner (Interchangeable) See text for Cell (if Needed) Removal Clearance Figure 4... -
Page 6: Typical Mounting Positions
TYPICAL MOUNTING POSITIONS Air Flow Air Flow Air Flow Rear View Rear View Figure 6 Figure 8 Figure 7 BASEMENT FURNACE HIGHBOY FURNACE (LOWBOY) (Figure 6) (Figure 8) COUNTERFLOW FURNACE (Figure 7) Cleaner is mounted hori- Side installation. Cleaner zontally in return plenum, is mounted vertically, Cleaner is mounted horizon- just above furnace. -
Page 7: Installation
INSTALLATION REMOVE OLD FILTER AND DISCARD (Figure 12) NOTE: This filter may be mounted in the furnace compart- ment. CLEAN BLOWER COMPARTMENT Figure 12 It is suggested that the furnace blower compartment, blower and blower housing be cleaned to ensure clean air circulation. -
Page 8: Wiring Instructions
10. With the cabinet Installed, reinstall pre-filter(s) and WIRING INSTRUCTIONS collecting cell(s) (Figure 19). NOTE: The contact button and handles on the cell 7. With the cabinet installed, the air cleaner can now be must be facing you and ionizing wires must be on the wired to electrical input source. -
Page 9: Operation
OPERATION 1. With the 120 VAC power turned on at the circuit breaker for the furnace, push the air cleaner ON-OFF switch to the “ON” position (Figure 20). 2. With the furnace blower running, the air cleaner will be operating. An arcing or “snapping” sound may be heard. -
Page 10: Specifications
REPLACING AN IONIZING WIRE If an ionizing wire should break, it can be replaced as follows: 1. Remove all pieces of broken wire. Make sure sup- ports at each end are in good condition and not bent out of shape. 2. -
Page 11: Basic Sst Service Guide
BASIC SST SERVICE GUIDE This guide will cover most homeowner complaints. If, after checking the items listed, the unit still fails to operate properly, contact the nearest Authorized Service Center. SERVICE INDICATION SERVICE CHECKS ON/OFF switch “ON” Unit functioning Normally Blower ON Operating Light ON ON/OFF switch “ON”... -
Page 12: Technical Repair Guide
TECHNICAL REPAIR GUIDE All voltage measurements indicated can be made with a WARNING high voltage D.C. probe and a general purpose volt ohm meter. For example: Simpson 260 or equivalent. Do not attempt repair of this unit unless you are familiar with the necessary tools, equipment, util- For test purposes, the air flow switch may be “wired out”... - Page 13 POWER SUPPLY 4. Using a standard extension cord, apply 120 VAC to power pack. Turn power switch to “ON” position. CHECKOUT PROCEDURE 5. Connect meter negative (-) lead to metal frame of 1. Turn power switch to the “OFF” position and remove collecting cell.
- Page 14 OZONE REDUCTION All electronic air cleaners typically produce a small amount of ozone that is within established limits. Some customers may notice an odor especially at high altitudes or low air flow rates. This power supply has a “hairpin” shaped jumper wire labeled W1 (see Fig 24) that can be cut and Cut and separate separated in case of such complaints.
-
Page 15: Repair Parts
REPAIR PARTS... - Page 16 REPAIR PARTS PARTS LIST FOR ELECTRONIC AIR CLEANERS When ordering repair parts, always give the following information as shown in this list. 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER 4. The NAME OF ITEM - Electronic Air Cleaner. Always order by “PART NUMBER”...
-
Page 17: Notice To Consumers
NOTICE TO CONSUMERS White-Rodgers Electronic Air Cleaner Dear Consumer; White-Rodgers would like to thank you for purchasing a White-Rodgers Electronic Air Cleaner or product containing a White-Rodgers Electronic Air Cleaner. Although White- Rodgers does not extend a warranty directly to consumers, White-Rodgers does extend a warranty to Wholesalers and Original Equipment Manufacturers who use White-Rodgers Products.
Need help?
Do you have a question about the Electro-Air SST 10C26S-010 and is the answer not in the manual?
Questions and answers