Sealey VS7026.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
ALWAYS KEEP FORCE SCREW
WELL LUBRICATED. MOLYBDENUM/
COPPER BASED GREASE
RECOMMENDED.
Refer to
instruction
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
‰
WARNING! Familiarise yourself with the specific applications and limitations of the kit, as well as any potential hazards.
‰
This kit should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer's manual.
9
Ensure that the kit is correct for the task.
9
Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey stockist.
9
DO NOT use the kit for any purpose other than that for which it is designed.
8
Ensure that the vehicle is properly supported with axle stands before working under the vehicle.
9
Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey stockist.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury.
8
DO NOT use the kit when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
8
After use, store in a safe, dry childproof area.
9
The force screw maximum recommended torque is 170Nm (M18x1.5), 155Nm (M16X1.5), 99Nm (M14X1.5), 60Nm (M12X1.5), 33Nm
(M10X1.5). Exceeding these torque values may shorten the life of the force screws. The force screws are considered to be
consumable items and are NOT covered under warranty.
2. INTRODUCTION
Comprehensive kit for fast and effective in situ removal/installation of wheel bearings, suspension bushes and
seals. Reduces the possibility of damaging the bearing/suspension housings. Supplied with 22 adaptors from
Ø44 to 90mm and five force screws. Adaptors can also be used in a standard workshop press when in situ
access isn't possible. Supplied in a storage case.
3. SPECIFICATION
Model No: ............................................................. VS7026.V3
External Adapter Diameter:
Ø44, 46, 48, 50, 52, 54, 56, 58, 60, 62, 64, 66, 68, 70, 72, 74,
76, 78, 80, 82, 85, 90mm
Force Screw Length: .................................................. 350mm
Force Screw Threads:
M10 x 1.5, M12 x 1.75, M14 x 2,0 M16 x 2.0, M18 x 2.5mm
Weight: ...................................................................... 17.73kg
4. CONTENTS
ADAPTERS
External Ø mm Internal Ø mm
44 34
46 36
48 38
50 40
52 42
54 44
56 46
58 48
60 50
62 52
64 54
66 56
68 58
70 60
© Jack Sealey Limited
BEARING & BUSH REMOVAL/INSTALLATION KIT
27PC
VS7026.V3
MODEL NO:
Part No.
VS7026-V3-01
VS7026-V3-02
VS7026-V3-03
VS7026-V3-04
VS7026-V3-05
VS7026-V3-06
VS7026-V3-07
VS7026-V3-08
VS7026-V3-09
VS7026-V3-10
VS7026-V3-11
VS7026-V3-12
VS7026-V3-13
VS7026-V3-14
Original Language Version
DO NOT USE AIR TOOLS
External Ø mm Internal Ø mm
72 62
74 64
76 66
78 68
80 70
82 72
85 75
90 80
FORCE SCREWS
Size
M10
M12
M14
M16
M18

Part No
VS7026-V3-15
VS7026-V3-16
VS7026-V3-17
VS7026-V3-18
VS7026-V3-19
VS7026-V3-20
VS7026-V3-21
VS7026-V3-22
Part No.
VS7026-V3-23
VS7026-V3-24
VS7026-V3-25
VS7026-V3-26
VS7026-V3-27
VS7026.V3 Issue:1 30/08/24