Page 1
4-Wheel Mobility Scooter | GUT161 Operator’s Manual Warning: Please read and thoroughly understand all instructions before operating. Failure to follow safety rules and other basic safety precautions may result in serious personal injury. Keep these instructions in a safe and easily accessible place so that they can be referred to when needed. Retain these instructions to assist in future servicing.
2. SAFETY INTRODUCTION 1. SAFETY INSTRUCTIONS. The below instructions and tips will help you to operate your Scooter safely. PLEASE NOTE - The Scooter is designed to be used by one person at a time and is not recommended for any person younger than 16 years old.
Page 4
11. INTENDED USE: This scooter is not designed or intended for stunt tricks, including but not limited to jumps, back wheel wheelies, front wheel wheelies, or operating while standing on the scooter. Always stay seated, keep both hands on the handlebar, both feet on the foot pedal and all three wheels touching the ground while operating the scooter.
4. CONTROLS AND FEATURES Backrest Seat Handle bar Battery Box Middle bar Rear Wheel LED & Horn D-pin Seat Post Clamp Main Frame Kit Front Wheel Brake Handle Lcd Display Seat Stand Post Clamp Disc Brake Handle Knob Rear Motor Wheel Shock Absorber Fording Locking Hook...
5. ASSEMBLY 1. Out of Package Take out the main frame kit, seat stand, seat, bolts and D-pin out of box (Fig.01). Most components are assembled in main frame kit. Fig. 01 Main Frame Kit Seat Stand Seat D-pin Bolts 2.
Page 8
3. Assemble the LED light Fig. 03 1) Take out the bolt, washer and nut which are pre- assembled at the handle-bar. Washer 2) Align the LED light at the bolt, shown as photo. (Fig.03) 3) Insert the bolt through light hook and handle-bar, and tighten the nut by the spanner.
Page 9
3) Lock the wire clip of D-pin to securely fix the Fig. 06 scooter. (Fig.06) Wire Clip 5. Assemble the Seat Stand Fig. 07 Bolts Failure to properly tighten the bolts holding the seat stand onto the seat may result in poor riding perfor- Seat Stand mance, the bolts falling off...
2) Close level of post clamp. If necessary, you can adjust the screw in post clamp to tighten more securely. (Fig.09) 6. OVERVIEW THE SCOOTER 1. Folding the Scooter Post Clamp Lever 1) Reverse the unfolding process to fold the scooter. 2) Open the wire clip of D-pin, and remove the D-pin.
Page 11
6. Battery Assembly Open the battery cover, and insert the battery until you here “click” voice. Holding the battery and trying to remove out battery. If not,the battery is assembled well. (Fig.12) Fig. 12 7. LED & Horn Fig. 13 1) The LED &...
Page 12
Fig. 15 Battery Level Drive Mode In Top Speed Power Button Drive Mode In Low Speed Reverse Mode Function Button Throttle Button 8. LCD Display The LCD display is at the right of handle bar. It controls the function and displays the Battery level, Speed level, and Driving mode.
11. Disc Brake Fig. 17 Fine Adjusting Nut ● The dual disc brakes are controlled by the brake wires. ● The rough adjusting nut was set well before shipping. But while you actuate the brake handle, the rear wheels are not braked completely. You can turn Rough Adjusting Nut the fine adjusting nut by counter-clockwise to make brake tighten.
Page 14
OPERATING SCOOTER The following can adversely affect steering and stability while operating your Scooter: ● Holding onto or attaching a leash to walk your pet. ● Carrying passengers (including pets). ● Hanging any article from the handle-bar. ● Towing or being pushed by another motorized vehicle. Keep both hands on the handle-bar and your feet on the foot pedal at all times while operating your Scooter.
Tips for driving the scooter on inclines and declines: ● Never travel up or down on an incline that is potentially hazardous such as one that is wet, icy, slippery, has loose gravel, etc. ● Always start an incline at the base of the hill and not at an angle. ●...
BATTERY AND CHARGER BATTERY Your scooter requires one 48 Volt Lithium-Ion battery that is easy detachable. 1. Fully charge the battery before first time operation or after a long period of non-usage. 2. For safety reasons, the battery is about 50% charged when shipped from the factory. 3.
BATTERY USE AND CARE WARNINGS 1. Battery must be fully charged before first use. 2. Plug the charger into a 110-240 AC outlet, a red light should appear on the charger. Charge the battery until the light on the charger turns solid green. 3.
10. TROUBLE SHOOTING Problem Possible cause Solution The scooter does The scooter is not turned on. Turn on scooter by pressing power button. not operate. The battery is not charged. Charge Battery. The hand brake and parking brake Make sure hand brake and parking brake are are inadvertently engaged.
Page 20
Thank you for your most recent purchase. Great Circle USA Follow us on social media Support Line: 1-866-493-0524 @SuperHandy help@superhandyus.com www.superhandyus.com Size: 210x285mm 157克双铜 REV 05/31/24...
Need help?
Do you have a question about the GUT161 and is the answer not in the manual?
Questions and answers