Ledvance OPTI-SELECT WALPAKNPS040UNHD8SC2ADJBZP Installation Instructions Manual
Ledvance OPTI-SELECT WALPAKNPS040UNHD8SC2ADJBZP Installation Instructions Manual

Ledvance OPTI-SELECT WALPAKNPS040UNHD8SC2ADJBZP Installation Instructions Manual

Performance class wall pack

Advertisement

Available languages

Available languages

4262082
LEDVANCE WALL PACK
Installation Instructions
PERFORMANCE CLASS
OPTI-SELECT WALL PACK
The Performance Class OPTI-SELECT Wall Pack offers
three lumen packages, three CCTs and 3 adjustable light
angles in the same product. It's controls-ready with a 3-pin
sensor receptacle and features an integrated photocell for
energy-efficient dusk-to-dawn operation. Sleek, durable, and
adaptable, it's perfect for commercial and industrial spaces.
For warranty coverage, please register at www.ledvanceUS.com
Please Read All Instructions Before Attempting Installation
• TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE, ONLY LICENSED ELECTRICIANS SHOULD PERFORM ALL
INSTALLATION SERVICES.
• TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE ATTEMPTING INSTALLATION OR
SERVICING.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC) AND ALL APPLICABLE
FEDERAL, STATE AND LOCAL ELECTRIC CODES AND SAFETY STANDARDS.
• USE ONLY UL (OR OTHER NTRL) APPROVED WIRE FOR INPUT/OUTPUT CONNECTIONS. MINIMUM SIZE 18 AWG OR 14 AWG
FOR CONTINUOUS RUNS.
• DO NOT INSTALL IN A HAZARDOUS ATMOSPHERE, EXCEPT WHERE THE AMBIENT TEMPERATURE DOES NOT EXCEED THE
RATED OPERATING TEMPERATURE OF THE FIXTURE.
• USE CAUTION WHEN HANDLING THIS PRODUCT DURING OR AFTER OPERATION AS IT MAY BECOME HOT AND CAUSE
BURNS. DISCONNECT PRODUCT AND ALLOW COOLING PRIOR TO SERVICING.
• ANY ALTERATION OR MODIFICATION OF THIS PRODUCT IS EXPRESSLY FORBIDDEN AS IT MAY CAUSE SERIOUS
PERSONAL INJURY, DEATH, PROPERTY DAMAGE AND/OR PRODUCT MALFUNCTION.
• TO PREVENT PRODUCT MALFUNCTION AND / OR ELECTRICAL SHOCK THIS PRODUCT MUST BE PROPERLY GROUNDED.
• CAUTION - RISK OF FIRE
• THIS LUMINAIRE IS DESIGNED TO OPERATE IN AMBIENT TEMPERATURES RANGING FROM -40°F TO +113°F
(-40°C TO +45°C) AND IS RATED FOR WET LOCATIONS.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Please visit: https://www.ledvanceus.com/fccpart15b
4308684
WARNING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OPTI-SELECT WALPAKNPS040UNHD8SC2ADJBZP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ledvance OPTI-SELECT WALPAKNPS040UNHD8SC2ADJBZP

  • Page 1 4262082 LEDVANCE WALL PACK Installation Instructions PERFORMANCE CLASS OPTI-SELECT WALL PACK The Performance Class OPTI-SELECT Wall Pack offers three lumen packages, three CCTs and 3 adjustable light angles in the same product. It’s controls-ready with a 3-pin sensor receptacle and features an integrated photocell for energy-efficient dusk-to-dawn operation.
  • Page 2: Safety Precautions

    4262082 Safety Precautions: IMPORTANT: READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN FOR FUTURE REFERENCE. GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier. Trouble Shooting Checklist Check your power source.
  • Page 3: Installation Instructions

    4262082 Installation Instructions 1. Turn Off Power: Ensure power is switched off at the 4. Choose an Installation Method: Select either Method A or circuit breaker to prevent electrical hazards Method B based on your desired installation type and proceed 2.
  • Page 4 4262082 7. Attach the Front Housing: Place the front housing onto 8. Reconnect the male and female connectors securely. the hinge of the rear housing. 9. Connect the Wires: Following the wiring diagram, 10. Close the front housing and tighten screws using a connect the fixture wires to the main power wires.
  • Page 5 4262082 Wiring Diagram: Detailed Wiring Diagram (with photocell and sensor receptacle): 4308684...
  • Page 6: Directives D'installation

    4262082 APPLIQUE MURALE LEDVANCE Directives d’installation APPLIQUE MURALE OPTI-SELECT DE CLASSE PERFORMANCE L’applique murale OPTI-SELECT de classe performance offre trois plages de lumens, trois TCP et 3 angles de lumière réglables dans un même produit. Compatible aux contrôles avec un réceptacle de détecteur à 3 fentes elle offre une cellule photoélectrique intégrée pour une opération crépusculaire...
  • Page 7: Avertissements De Sécurité

    4262082 Avertissements de sécurité : IMPORTANT : Veuillez lire attentivement les directives d’installation avant l’installation de ce luminaire. Garder ces directives pour référence future. GÉNÉRAL : Lors de la réception de l'appareil, vérifiez soigneusement qu'il n'y a pas de dommages causés durant le transport et si des dommages sont constatés aviser le transporteur.
  • Page 8 4262082 Directives d’installation 1. Couper l’alimentation. S’assurer que l’alimentation 4. Choisir une méthode d’installation : choisir soit la méthode est coupée au disjoncteur afin d’éviter les chocs A ou la méthode B selon le type d’installation recherché et électriques. faire comme suit : 2.
  • Page 9 4262082 7. Rattacher le boîtier avant : placer le boîtier avant sur la 8. Raccorder les connecteurs mâle et femelle de manière charnière à l’arrière du boîtier. sécuritaire. 9. Raccorder les fils : en respectant les dessins de câblage 10. Refermer le boîter avant et resserrer les vis à l’aide raccorder les fils du luminaire avec les fils d’alimentation.
  • Page 10 4262082 Dessin de câblage : 4308684...

Table of Contents