Yamaha XVS95CTD Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Motorcycle
  5. XVS95CTD
  6. Owner's manual
Yamaha XVS95CTD Owner's Manual

Yamaha XVS95CTD Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Read this manual carefully before operating this vehicle.
OWNER'S MANUAL
XVS95CTD(C)
LIT-11626-26-10
26S-28199-14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XVS95CTD and is the answer not in the manual?

Questions and answers

Related Manuals for Yamaha XVS95CTD

Summary of Contents for Yamaha XVS95CTD

  • Page 1 Read this manual carefully before operating this vehicle. OWNER’S MANUAL XVS95CTD(C) LIT-11626-26-10 26S-28199-14...
  • Page 2 EAU10042 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
  • Page 3 Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.

  • Page 4: Important Manual Information

    IMPORTANT MANUAL INFORMATION EAU10133 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
  • Page 5 IMPORTANT MANUAL INFORMATION EAU10193 XVS95CTD(C) OWNER’S MANUAL ©2012 by Yamaha Motor Corporation, U.S.A. 1st edition, March 2012 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.

  • Page 6: Table Of Contents

    TABLE OF CONTENTS LOCATION OF IMPORTANT Sidestand ........4-15 Adjusting the clutch lever free LABELS ..........1-1 Ignition circuit cut-off system ..4-16 play ........... 7-17 Adjusting the brake lever free SAFETY INFORMATION ....2-1 FOR YOUR SAFETY – play ........... 7-18 PRE-OPERATION CHECKS .....
  • Page 7 Matte color caution ......8-1 Care ..........8-1 Storage ...........8-4 SPECIFICATIONS ......9-1 CONSUMER INFORMATION...10-1 Identification numbers ....10-1 Reporting safety defects ....10-3 Motorcycle noise regulation ..10-4 Maintenance record ......10-5 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY ......10-7 YAMAHA EXTENDED SERVICE (Y.E.S.) ........10-9...

  • Page 8: Location Of Important Labels

    Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
  • Page 9 LOCATION OF IMPORTANT LABELS 1 California only VACUUM HOSE ROUTING Improper loading can adversely affect handling. Do not exceed maximum load limit : 5kg (11lb) each saddlebag. Distribute weight evenly from side to side. PRESS. SENSOR Read the Owner's manual for important loading and tire pressure information.
  • Page 10 LOCATION OF IMPORTANT LABELS...
  • Page 11 LOCATION OF IMPORTANT LABELS Improper loading can adversely affect handling. Do not exceed maximum load limit : 5kg (11lb) each saddlebag. Distribute weight evenly from side to side. Read the Owner's manual for important loading and tire pressure information. Total weight of rider, passenger, accessories, and cargo must not exceed the motorcycle load capacity shown in the Owner's Manual.

  • Page 12: Safety Information

    SAFETY INFORMATION ● EAU1028A Never operate a motorcycle with- yourself conspicuous appears to out proper training or instruction. be very effective in reducing the Take a training course. Beginners chance of this type of accident. Be a Responsible Owner should receive training from a cer- Therefore: As the vehicle’s owner, you are respon- tified instructor.
  • Page 13 SAFETY INFORMATION ● Many accidents involve inexperi- • Always signal before turning or Protective Apparel enced operators. In fact, many op- changing lanes. Make sure that The majority of fatalities from motorcy- erators who have been involved in other motorists can see you. cle accidents are the result of head in- ●...
  • Page 14 SAFETY INFORMATION ● Avoid Carbon Monoxide Poisoning Do not run engine outdoors where When loading within this weight limit, All engine exhaust contains carbon engine exhaust can be drawn into keep the following in mind: monoxide, a deadly gas. Breathing car- a building through openings such ●...
  • Page 15 Yamaha accessories, which are avail- formed to your vehicle that change any lightweight as possible and able only from a Yamaha dealer, have of the vehicle’s design or operation should be kept to a minimum. been designed, tested, and approved characteristics can put you and others •...
  • Page 16 SAFETY INFORMATION ● tor and may limit control ability, Check that the fuel cock (if therefore, such accessories are equipped) is in the “OFF” position not recommended. and that there are no fuel leaks. ● ● Use caution when adding electri- Point the front wheel straight cal accessories.

  • Page 17: Description

    DESCRIPTION EAU10410 Left view 2,3,4 1. Headlight (page 7-29) 9. Engine oil drain bolt (page 7-11) 2. Main fuse (page 7-28) 10.Shift pedal (page 4-8) 3. Fuse box (page 7-28) 11.Engine oil filler cap (page 7-11) 4. Fuel injection system fuse (page 7-28) 5.

  • Page 18: Right View

    DESCRIPTION EAU10420 Right view 1. License plate light (page 7-32) 9. Rear brake light switch (page 7-18) 2. Tail/brake light (page 7-30) 10.Brake pedal (page 4-8) 3. Battery (page 7-26) 4. Seat lock (page 4-12) 5. Air filter element (page 7-13) 6.

  • Page 19: Controls And Instruments

    DESCRIPTION EAU10430 Controls and instruments 1. Clutch lever (page 4-7) 2. Left handlebar switches (page 4-6) 3. Multi-function meter unit (page 4-3) 4. Main switch/steering lock (page 4-1) 5. Front brake fluid reservoir (page 7-19) 6. Right handlebar switches (page 4-6) 7.

  • Page 20: Instrument And Control Functions

    INSTRUMENT AND CONTROL FUNCTIONS EAU10461 EAU10661 To lock the steering Main switch/steering lock All electrical systems are off. The key can be removed. EWA10061 WARNING Never turn the key to “OFF” or “LOCK” while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in LOCK loss of control or an accident.

  • Page 21: Indicator Lights And Warning Lights

    4. Oil level warning light “ ” or if the warning light remains on, have 5. Turn signal indicator light “ ” a Yamaha dealer check the electrical 6. High beam indicator light “ ” circuit. EAU11020 Turn signal indicator light “...

  • Page 22: Multi-Function Meter Unit

    The oil level warning then go off for 3.0 seconds. If this oc- light will flash ten times, then go off curs, have a Yamaha dealer check the for 2.5 seconds. If this occurs, vehicle. have a Yamaha dealer check the vehicle.
  • Page 23 INSTRUMENT AND CONTROL FUNCTIONS ● two tripmeters (which show the Speedometer Odometer, tripmeters, fuel reserve distance traveled since they were tripmeter and clock last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled on the fuel reserve) ●...
  • Page 24 To reset a tripmeter, select it by push- 4. Push the “RESET” switch to set code number, and then have a Yamaha ing the “SELECT” switch, and then the minutes. dealer check the vehicle.

  • Page 25: Handlebar Switches

    INSTRUMENT AND CONTROL FUNCTIONS To set the brightness EAU1234A Right Handlebar switches 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” Left switch. 3. Turn the key to “ON”, and then re- lease the “SELECT” switch after five seconds.

  • Page 26: Clutch Lever

    INSTRUMENT AND CONTROL FUNCTIONS has traveled both about 150 m (490 ft) EAU12711 EAU12820 Start switch “ ” Clutch lever and for approximately 15 seconds. Push this switch to crank the engine However, the turn signal lights can also with the starter. See page 6-1 for start- be canceled manually by pushing the ing instructions prior to starting the en- switch in after it has returned to the cen-...

  • Page 27: Shift Pedal

    INSTRUMENT AND CONTROL FUNCTIONS EAU12881 EAU12891 EAU12941 Shift pedal Brake lever Brake pedal 1. Shift pedal 1. Brake lever 1. Brake pedal 2. Neutral position The brake lever is located on the right The brake pedal is on the right side of The shift pedal is located on the left side of the handlebar.

  • Page 28: Fuel Tank Cap

    INSTRUMENT AND CONTROL FUNCTIONS EAU13122 2. Turn the key counterclockwise to EAU13221 Fuel tank cap Fuel the original position, remove it, and Make sure there is sufficient gasoline in then close the lock cover. the tank. EWA10881 WARNING The fuel tank cap cannot be installed unless the key is in the lock.
  • Page 29 EWA15151 as well as to the exhaust system. WARNING Gasoline is poisonous and can Your Yamaha engine has been de- cause injury or death. Handle gaso- signed to use unleaded gasoline with a line with care. Never siphon gaso- pump octane number [(R+M)/2] of 86 or line by mouth.

  • Page 30: Fuel Tank Breather/Overflow Hose

    INSTRUMENT AND CONTROL FUNCTIONS EAU48760 EAU13433 ECA10701 Fuel tank breather/overflow Catalytic converter NOTICE hose This model is equipped with a catalytic Use only unleaded gasoline. The use converter in the exhaust system. of leaded gasoline will cause unre- EWA10862 pairable damage to the catalytic WARNING converter.

  • Page 31: Rider Seat

    INSTRUMENT AND CONTROL FUNCTIONS EAU42752 EAU14324 Rider seat Helmet holder To remove the rider seat 1. Insert the key into the seat lock, and then turn it counterclockwise. 1. Projection 2. Seat holder 1. Helmet holder 2. Push the front of the seat down to The helmet holder is located under the lock it in place.

  • Page 32: Sidecases

    INSTRUMENT AND CONTROL FUNCTIONS To release the helmet from the hel- EAU47060 To open a sidecase Sidecases met holder 1. Insert the key into the lock, turn it EWA12520 Remove the rider seat, remove the hel- counterclockwise, and then push it WARNING met from the helmet holder, and then Improper loading or overloading can...

  • Page 33: Adjusting The Shock Absorber Assembly

    1. Panel A Polish the dry leather with a soft pension, turn the adjusting ring in 2. Spring preload adjusting ring cloth, and then treat with Yamaha direction (b). Mink Oil or another high-quality This shock absorber assembly is leather protectant for increased...

  • Page 34: Sidestand

    Spring preload setting: EWA10241 Minimum (soft): sembly yourself. Take the shock WARNING absorber assembly to a Yamaha Standard: The vehicle must not be ridden with dealer for any service. the sidestand down, or if the side- Maximum (hard):...

  • Page 35: Ignition Circuit Cut-Off System

    INSTRUMENT AND CONTROL FUNCTIONS this system regularly and have a EAU44892 Ignition circuit cut-off system Yamaha dealer repair it if it does not The ignition circuit cut-off system (com- function properly. prising the sidestand switch, clutch switch and neutral switch) has the fol- lowing functions.
  • Page 36 INSTRUMENT AND CONTROL FUNCTIONS WARNING With the engine turned off: 1. Move the sidestand down. If a malfunction is noted, have a Yamaha 2. Make sure that the engine stop switch is set to “ ”. dealer check the system before riding.

  • Page 37: For Your Safety - Pre-Operation Checks

    • If necessary, add recommended oil to specified level. 7-11 • Check vehicle for oil leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check lever free play. • Adjust if necessary. Front brake •...
  • Page 38 • Make sure that operation is smooth. • Check throttle grip free play. Throttle grip 7-14, 7-22 • If necessary, have Yamaha dealer adjust throttle grip free play and lubricate cable and grip housing. • Make sure that operation is smooth. Control cables 7-22 •...
  • Page 39 FOR YOUR SAFETY – PRE-OPERATION CHECKS ITEM CHECKS PAGE • Check operation of ignition circuit cut-off system. Sidestand switch 4-15 • If system is not working correctly, have Yamaha dealer check vehicle.

  • Page 40: Operation And Important Riding Points

    ● a lean angle sensor to stop the en- ● understand, ask your Yamaha dealer. The transmission is in the neutral gine in case of a turnover. In this position. EWA10271...

  • Page 41: Shifting

    The neutral indicator light should come on. If not, ask a ● Even with the transmission in Yamaha dealer to check the elec- the neutral position, do not trical circuit. coast for long periods of time 3. Start the engine by pushing the with the engine off, and do not start switch.

  • Page 42: Engine Break-In

    OPERATION AND IMPORTANT RIDING POINTS 4. At the recommended shift points 3. Shift the transmission into the neu- EAU16841 Engine break-in shown in the following table, close tral position when the motorcycle There is never a more important period the throttle, and at the same time, is almost completely stopped.

  • Page 43: Parking

    If any engine trouble should occur WARNING during the engine break-in period, ● Since the engine and exhaust immediately have a Yamaha dealer system can become very hot, check the vehicle. park in a place where pedestri- ans or children are not likely to touch them and be burned.

  • Page 44: Periodic Maintenance And Adjustment

    – possibly leading to pending on the weather, terrain, geo- that is certified (if applicable). Yamaha death. See page 2-3 for more in- graphical location, and individual use, dealers are trained and equipped to...

  • Page 45: Owner's Tool Kit

    If you do not have the tools or experi- ence required for a particular job, have a Yamaha dealer perform it for you.

  • Page 46: Periodic Maintenance Chart For The Emission Control System

    From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. ● Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17601 Periodic maintenance chart for the emission control system...
  • Page 47 PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months Evaporative emis-...

  • Page 48: General Maintenance And Lubrication Chart

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU32187 General maintenance and lubrication chart INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months...
  • Page 49 PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months •...
  • Page 50 Front and rear brake √ √ √ √ √ √ 24 * • Check operation. switches • Apply Yamaha chain and cable √ √ √ √ √ √ 25 * Control cables lube or engine oil thoroughly. • Check operation.
  • Page 51 PERIODIC MAINTENANCE AND ADJUSTMENT EAU17650 ● Air filter • This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com- pressed air to avoid damaging it. • The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas. ●...

  • Page 52: Removing And Installing The Panel

    Do not attempt to diagnose such problems yourself. Instead, have To remove the panel a Yamaha dealer check the vehicle. Remove the bolt, and then pull the pan- If a spark plug shows signs of electrode el off as shown.

  • Page 53: Canister (For California Only)

    PERIODIC MAINTENANCE AND ADJUSTMENT Before installing a spark plug, the spark EAU19681 Canister (for California only) plug gap should be measured with a If a torque wrench is not available when wire thickness gauge and, if necessary, installing a spark plug, a good estimate adjusted to specification.

  • Page 54: Engine Oil And Oil Filter Cartridge

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU47112 5. If the engine oil is at or below the Engine oil and oil filter car- minimum level mark, add sufficient The engine oil should be between the tridge oil of the recommended type to minimum and maximum level marks.
  • Page 55 PERIODIC MAINTENANCE AND ADJUSTMENT An oil filter wrench is available at a Yamaha dealer. 5. Apply a thin coat of clean engine oil to the O-ring of the new oil filter cartridge. 1. Engine oil drain bolt 1. Torque wrench 2.

  • Page 56: Replacing The Air Filter Element

    NOTICE correct, immediately turn the engine ● In order to prevent clutch slip- off and have a Yamaha dealer check page (since the engine oil also the vehicle. lubricates the clutch), do not 10. Turn the engine off, wait a few min- mix any chemical additives.

  • Page 57: Checking The Throttle Grip Free Play

    The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart. 1. Air filter element 3.

  • Page 58: Tires

    Yamaha dealer immediately and Tire inflation pressure should be have the tire replaced. checked and adjusted when the tem- Minimum tire tread depth (front and...

  • Page 59: Cast Wheels

    If any and brake-related parts, includ- the vehicle may be different, which damage is found, have a Yamaha ing the tires, should be left to a could lead to an accident. dealer replace the wheel. Do not...

  • Page 60: Adjusting The Clutch Lever Free Play

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU50270 decrease the clutch lever free play, decrease the clutch lever free play, Adjusting the clutch lever free turn the adjusting bolt in direction turn the adjusting nut in direction play (b). (b). 7. Tighten the locknut at the clutch cable, and then slide the rubber If the specified clutch lever free play covers to their original positions.

  • Page 61: Adjusting The Brake Lever Free Play

    If there is air in the hy- draulic system, have a Yamaha 1. Rear brake light switch dealer bleed the system before 2. Rear brake light switch adjusting nut 1.

  • Page 62: Checking The Front And Rear Brake Pads

    EAU22581 Checking the front and rear Checking the brake fluid level peared, have a Yamaha dealer replace brake pads Before riding, check that the brake fluid the brake pads as a set. is above the minimum level mark.
  • Page 63 ● Rear brake Use only the specified brake flu- fluid level goes down suddenly, have a id; otherwise, the rubber seals Yamaha dealer check the cause before may deteriorate, causing leak- further riding. age. ● Refill with the same type of brake fluid.

  • Page 64: Changing The Brake Fluid

    Changing the brake fluid Drive belt slack with a force of 45 N (4.5 kgf, 10 lbf) Have a Yamaha dealer change the The drive belt slack should be checked applied to the belt with a belt ten- brake fluid at the intervals specified in and adjusted at the intervals specified sion gauge as shown.

  • Page 65: Checking And Lubricating The Cables

    5. If the drive belt slack is incorrect, EAU23095 EAU49920 Checking and lubricating the Checking and lubricating the have a Yamaha dealer adjust it. cables throttle grip and cable The operation of all control cables and The operation of the throttle grip should the condition of the cables should be be checked before each ride.

  • Page 66: Checking And Lubricating The Brake And Shift Pedals

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU44273 EAU23143 Recommended lubricant: Checking and lubricating the Checking and lubricating the Lithium-soap-based grease brake and shift pedals brake and clutch levers The operation of the brake and shift The operation of the brake and clutch pedals should be checked before each levers should be checked before each ride, and the pedal pivots should be lu-...

  • Page 67: Checking And Lubricating The Sidestand

    The operation of the sidestand should The pivoting points of the rear suspen- be checked before each ride, and the sion must be lubricated by a Yamaha sidestand pivot and metal-to-metal dealer at the intervals specified in the contact surfaces should be lubricated if periodic maintenance and lubrication necessary.

  • Page 68: Lubricating The Swingarm Pivots

    The swingarm pivots must be lubricat- face and hold it in an upright posi- fork does not operate smoothly, ed by a Yamaha dealer at the intervals tion. WARNING! To avoid injury, have a Yamaha dealer check or re- specified in the periodic maintenance securely support the vehicle so pair it.

  • Page 69: Checking The Steering

    If any free (Valve Regulated Lead Acid) battery. the wheel bearings. play can be felt, have a Yamaha There is no need to check the electro- dealer check or repair the steering. lyte or to add distilled water. However, the battery lead connections need to be checked and, if necessary, tightened.
  • Page 70 To charge the battery once a month and fully charge it if Have a Yamaha dealer charge the bat- necessary. tery as soon as possible if it seems to 3. Fully charge the battery before in- have discharged.

  • Page 71: Replacing The Fuses

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU47134 Replacing the fuses The main fuse, the fuel injection system fuse, and the fuse box, which contains the fuses for the individual circuits, are located under the rider seat. (See page 4-12.) 1. Ignition fuse 1.

  • Page 72: Replacing The Headlight Bulb

    4. If the fuse immediately blows using a cloth moistened with al- again, have a Yamaha dealer cohol or thinner. check the electrical system. ● Headlight lens...

  • Page 73: Replacing The Tail/Brake Light Bulb

    6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 1. Headlight bulb holder 4. Place a new headlight bulb into po- sition, and then secure it with the bulb holder.

  • Page 74: Replacing A Front Turn Signal Light Bulb

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU42462 Replacing a front turn signal light bulb 1. Remove the front turn signal light outer lens by removing the screws. 1. Tail/brake light bulb 1. Outer lens 2. Inner lens 3. Insert a new bulb into the socket, 3.

  • Page 75: Replacing A Rear Turn Signal Light Bulb

    PERIODIC MAINTENANCE AND ADJUSTMENT EAU42453 EAU24324 Replacing a rear turn signal Replacing a license plate light light bulb bulb 1. Remove the turn signal light lens 1. Remove the license plate light unit by removing the screws. by removing the nuts, washers and rubber dampers.

  • Page 76: Supporting The Motorcycle

    PERIODIC MAINTENANCE AND ADJUSTMENT 6. Install the license plate light unit by EAU24350 Supporting the motorcycle installing the rubber dampers, Since this model is not equipped with a washers and the nuts. centerstand, follow these precautions when removing the front and rear wheel or performing other maintenance requiring the motorcycle to stand up- right.

  • Page 77: Troubleshooting

    However, should your motorcycle require any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, experience, and know-how to service the motorcycle properly.

  • Page 78: Troubleshooting Chart

    Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.

  • Page 79: Motorcycle Care And Storage

    Rust and corrosion can develop matte colored finished parts. Be Cleaning even if high-quality components are sure to consult a Yamaha dealer for ECA10772 advice on what products to use be- used. A rusty exhaust pipe may go un-...
  • Page 80 For For motorcycles equipped with combination with water, carry out the a windshield: Do not use strong additional cleaning, use Yamaha Wind- following steps after each ride in the shield Cleaner or other quality cleaner. cleaners or hard sponges as...
  • Page 81 Avoid combination ● Never apply oil or wax to any with Yamaha Mink Oil or another high- cleaner waxes, many of which rubber and plastic parts, but quality leather protectant for increased...

  • Page 82: Storage

    MOTORCYCLE CARE AND STORAGE EAU26282 2. Fill up the fuel tank and add fuel e. Remove the spark plug caps Storage stabilizer (if available) to prevent from the spark plugs, and then the fuel tank from rusting and the install the spark plugs and the Short-term fuel from deteriorating.
  • Page 83 MOTORCYCLE CARE AND STORAGE Make any necessary repairs before storing the motorcycle.

  • Page 84: Specifications

    Throttle body: 1000 mm (39.4 in) SAE 10W-30, 10W-40, 10W-50, 15W-40, ID mark: Overall height: 20W-40 or 20W-50 XVS95CTD 5S71 00 1340 mm (52.8 in) XVS95CTDC 5S72 10 10 30 50 70 90 110 130 ˚F Seat height: Spark plug(s): 675 mm (26.6 in)
  • Page 85 SPECIFICATIONS 4th: Tire air pressure (measured on cold Operation: 1.259 (34/27) Right foot operation tires): 5th: Specified brake fluid: Loading condition: 1.042 (25/24) DOT 4 0–90 kg (0–198 lb) Chassis: Front suspension: Front: Frame type: Type: 225 kPa (2.25 kgf/cm², 33 psi) Double cradle Telescopic fork Rear:...
  • Page 86 SPECIFICATIONS Tail/brake light: Fuel injection system fuse: 12 V, 5.0 W/21.0 W × 1 10.0 A Front turn signal/position light: Backup fuse: 12 V, 21 W/5.0 W × 2 10.0 A Rear turn signal light: 12 V, 21.0 W × 2 License plate light: 12 V, 3.8 W ×...

  • Page 87: Consumer Information

    Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
  • Page 88 This information illustration. This label shows specifica- will be needed when ordering spare tions related to exhaust emissions as parts from a Yamaha dealer. required by federal law, state law and Environment Canada. 10-2...

  • Page 89: Reporting Safety Defects

    If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

  • Page 90: Motorcycle Noise Regulation

    CONSUMER INFORMATION EAU26560 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve- hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.

  • Page 91: Maintenance Record

    CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required.
  • Page 92 CONSUMER INFORMATION Maintenance Date of Servicing dealer Mileage Remarks interval service name and address 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months 10-6...

  • Page 93: Yamaha Motor

    CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that CUSTOMER’S RESPONSIBILITY under this Engine new Yamaha motorcycles will be free from defects in warranty shall be to: Period Displacement...
  • Page 94 CUSTOMER SERVICE What costs are my responsibility during the warranty period? If your machine requires warranty service, you must take it to any authorized Yamaha The customer’s responsibility includes all costs of normal maintenance services, motorcycle dealer within the continental United States. Be sure to bring your warranty non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, registration card or other valid proof of the original date of purchase.

  • Page 95: Yamaha Extended Service (Y.e.s.)

    This excellent Y.E.S. plan coverage is only available to dealer to see how comforting uninterrupted factory- Yamaha owners like you, and only while your Yamaha is still backed protection can be. within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts.
  • Page 96 Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
  • Page 97 INDEX Fuel tank breather/overflow hose..4-11 Part locations .......... 3-1 Fuel tank cap...........4-9 Air filter element, replacing ....7-13 Fuses, replacing........7-28 Rear suspension, lubricating ....7-24 RESET switch......... 4-7 Battery ..........7-26 Handlebar switches .........4-6 Rider seat ..........4-12 Brake and clutch levers, Headlight bulb, replacing.......7-29 checking and lubricating.....
  • Page 98 INDEX Turn signal light bulb (front), replacing ..........7-31 Turn signal light bulb (rear), replacing ..........7-32 Turn signal switch ........4-6 Valve clearance ........7-14 Vehicle Emission Control Information label ............ 10-2 Vehicle identification number ....10-1 Warranty, extended....... 10-9 Warranty, limited ........
  • Page 99 Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.
  • Page 100 PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2012.04-0.9×1 CR...

This manual is also suitable for:

Star 2012Xvs95ctdc

Table of Contents