Subscribe to Our Youtube Channel
Related Manuals for infobit iMatrix C604
Summary of Contents for infobit iMatrix C604
- Page 1 C604 4K60 6x4 Seamless Matrix Switcher with USB C User Manual V1.0 INFOBIT AV www.infobitav.com info@infobitav.com...
-
Page 2: Table Of Contents
10.2 TELNET ..........................13 11. CONTROL VIA WEB UI ....................14 11.1 LOG IN ..........................14 11.2 WEB UI INTRODUCTION ....................16 11.2.1 MATRIX CONTROL ........................... 16 11.2.2 GENERAL SETTING ........................... 26 11.2.3 ADVANCED SETTING ........................29 INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 3: Introduction
1. INTRODUCTION The iMatrix C604 is a fixed 1RU 6x4 fast switching matrix with both USB-C and HDMI inputs. It builds in 4K60 scaler on all video outputs, and features seamless transition when switching video inputs. The USB-C input is fully featured, which supports 4K60, USB 3.1 gen1, 1G network and PD 3.0 USB host charging up to... -
Page 4: Package List
3. PACKAGE LIST 1 x iMatrix C604 1 x AC Power Cord 1 x USB 3.1 Gen 1 Type-C to Type-C Cable (2m, 5Gbps per lane) 3 x Phoenix Male Connector (3.5mm 3-Pin) 4 x Phoenix Male Connector (3.5mm 5-Pin) 1 x Phoenix Male Connectors (3.5mm 6-Pin) - Page 5 17.32'' x 1.71'' x 12.99'' (440mm x 43.5mm x 330mm) Net Weight 10.03lbs (4.55kg) Transmission Distance Cable Type Range Supported Video HDMI Input/Output: 15m/49ft 1080P@60Hz Input/Output: 10m/33ft 4K@30Hz 4:4:4 24bpp Input/Output: 5m/16ft 4K@60Hz 4:4:4 24bpp USB Type-C 2m/7ft 4K@60Hz 4:4:4 24bpp INFOBIT AV www.infobitav.com info@infobitav.com...
-
Page 6: Panel Overview
Ÿ VIDEO: Press the left/right button to switch input port and the up/down button to turn the page to display video information of current selected input. Button Press to apply the settings. CANCEL Button Press to cancel the button operation or exit current mode. INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 7: Rear Panel
The following cable are recommended to use: USB Type-C to Type-C cable (USB 3.0 or above) Connect to HDMI sources. HDMI IN 2~6 Connect to HDMI displays. HDMI OUT 1~4 RJ45 port. Connect to Ethernet devices for LAN control (Web UI/Telnet). INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 8: Installation
Note: Before installation, ensure the device is disconnected from the power source. The matrix occupies 1U space and can be placed on a solid and stable surface or installed on a standard equipment rack. To install the matrix on an equipment rack: INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 9: Applications
2. Affix the matrix to the mounting rack using the mounting screws. 7. APPLICATIONS 7.1 DANTE The iMatrix C604 supports 4x4 Dante audio transmission. Before using Dante function, please enable all devices are connected to the same network, as the Dante Controller is only available on wired connections. -
Page 10: Local Presentation
Figure 4: Application of Local Presentation 7.3 LARGE LECTURE HALL It supports seamless switching among lecture's laptop, Room PC, document camera, web cameras, or BYOD devices in tranining applications. Figure 5: Application of Large Lecture Hall INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 11: Unified Communications
View IP address from LCD screen on front panel. After the device starts up, the IP address will be displayed on the LCD screen, or you can press the INFO button to view it. Sending API command “GET IPADDR<CR><LF>” via RS232 or telnet. See “Command Control” section to get detail information. INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 12: Control Via Front Panel
4. Press “CANCEL” to exit the mode and return to the main page. 9.3 GET INFORMATION OF DEVICE/INPUT VIDEO Press “INFO” button to enter device information viewing mode or press “VIDEO” button to enter video information viewing mode. INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 13: Control Via Command
A professional RS232 serial interface software (e.g., Serial Assist) may be needed as well. Parameters Default Value Baud Rate 9600 bps Data bits 8 bits Parity None Stop bits 1 bit Flow control None 10.2 TELNET INFOBIT AV www.infobitav.com info@infobitav.com... -
Page 14: Control Via Web Ui
Check the device’s IP address through the LCD screen or sending API command, see “Obtain IP address” section to get detail information. Input the device’s IP address in the browser and press Enter. The Login window appears. INFOBIT AV www.infobitav.com info@infobitav.com... - Page 15 4 to 16 characters in length. Figure 8: Change Password Window The main page opens. Click the tabs on the navigation pane above to access the corresponding web page. Figure 9: Main Page INFOBIT AV www.infobitav.com info@infobitav.com...
-
Page 16: Web Ui Introduction
None: None input is routed to the output (or the output is turned off). By default, Video Input 1 routes to Output 1…Video Input 3 routes to Output 3, Video Input 4 routes to Output 4. 2. Audio Routing INFOBIT AV www.infobitav.com info@infobitav.com... - Page 17 Figure 12: Highlight Audio Routing Path The Grey blue zone shows the input and output distribution according video routing. When select audio source here, it indicates that select the de-embedded audio from the input source the corresponding output routed. INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 18 3). Audio DSP Configurations for Audio Inputs A. GAIN Figure 14: Audio Input Gain Setting Parameter Function Volume Meter (For Display the active audio level of the corresponding audio input in real-time. all audio inputs) INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 19 Range: 1~2000ms; Default setting: 1000ms. Ÿ Ratio: To select the amount of the expansion applies to the audio signal from the dropdown menu. INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 20 Adjust the knob or enter a value to specify the cutoff frequency, at and above which the filter allows signals to pass through more effectively, and below which the filter attenuates (reduces the amplitude of) the signals. Default setting: 20Hz D. COMP Figure 17: Audio Input Compressor Setting INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 21 When multiple audio outputs are present, the selected primary audio needs to play, and the ducking function will automatically reduce the volume of other audio signals. Click “On/Off” button to enable/disable Duck function. Default setting: Off. When set it to on: INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 22 Figure 20: Audio Output HPF Setting EQ—Equalizer, is used to change the balance of different frequency components in the audio signal. Click On/Off button to enable/disable the EQ function. Default setting: Off. When set it to on: INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 23 (reduces the amplitude of) the signals. Tip: To reset the value to factory default quickly, press and hold the “Ctrl” key and click the inside of the knob. Default setting: 20KHz E. VOL Figure 22: Audio Output VOL Setting INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 24 This section allows users to select USB host all USB devices connected. Active USB Host Selection: Select the USB Host from the drop-menu. Default Setting: USB-B Port1. Figure 24: USB Routing Selection For example, when select USB-B Port2, all USB devices will connected to USB-B Port 2. INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 25 Display On/Off: Input the corresponding CEC command, then click “Save” to save it. Note: If users want to change CEC commands, please refer to the CEC specification document. 5. Preset INFOBIT AV www.infobitav.com info@infobitav.com...
-
Page 26: General Setting
The matrix supports save 24 presets at maximum. Preset Name: Input a preset name. • Save: Save the selection settings to the matrix. • Load: Load the saved preset file from the matrix. • 11.2.2 GENERAL SETTING 1). A/V Configuration INFOBIT AV www.infobitav.com info@infobitav.com... - Page 27 Fixed 4K60 2.0CH PCM Audio with SDR; Fixed 4K30 2.0CH PCM Audio with HDR; Fixed 4K30 2.0CH PCM Audio with SDR; Fixed 1080p@60Hz 2.0CH PCM Audio with HDR; Fixed 1080p@60Hz 2.0CH PCM Audio with SDR; EDID Write. INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 28 When select Digital In (default): Low-state Threshold (V): Define the low detect voltage threshold (the range is 1 to 22V). High state Threshold (V): Define the high detect voltage threshold (the range is 2 to 23V). INFOBIT AV www.infobitav.com info@infobitav.com...
-
Page 29: Advanced Setting
When it is set to “Off”, NC and COM pins of the selected relay port are connected, and NO and COM pins of the selected relay port are disconnected. 11.2.3 ADVANCED SETTING 1). Information INFOBIT AV www.infobitav.com info@infobitav.com... - Page 30 Set the DANTE LAN port: Select the mode from the drop-down menu. Default setting: Independent. When set to Independent, the DANTE LAN port is isolated from another LAN port • and used for DANTE audio connection. Only the other LAN port can access to Web INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 31 HTTP network protocol is the most widely used hypertext transfer protocol, this method allows a third-party to listen in and eavesdrop on the transferred information. To ensure the secure data transmission, the HTTP can be disabled, INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 32 The matrix will reboot automatically after upgrading is completed. Refresh the webpage and log in again to the web UI. Note: Do not interrupt or power off the matrix during the upgrading. 7). System Figure 44: System INFOBIT AV www.infobitav.com info@infobitav.com...
- Page 33 Apply: Click “Apply” to send the input command to the matrix. For example: Figure 46: Telnet API Command Example 9). Log Figure 47: Log This section shows the operation log and commands return. Export Log: Click to export the log file to local PC. INFOBIT AV www.infobitav.com info@infobitav.com...
Need help?
Do you have a question about the iMatrix C604 and is the answer not in the manual?
Questions and answers