4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 1. Product Introduction Thanks for choosing the 6x2 multi-format presentation matrix switcher! The matrix switcher simplifies meeting room and presentation space system integration by providing four HDMI inputs, one VGA input, one USB-C input, one HDBT output and one HDMI output.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 2. Specification Video Input Video Input (4) HDMI, (1) VGA, (1) USB-C Video Input Connector (4) Type-A female HDMI, (1) 15-pin female VGA, (1) USB-C HDMI: Up to 4K@60Hz 4:4:4, HDR VGA: Up to 1920x1200@60Hz Video input Video Resolution USB-C: Up to 4K@60Hz 4:2:0 Video Output...
Page 7
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher HDMI Version Up to 2.0 HDCP Version Up to 2.2 Bandwidth 18Gbps 1080p@60Hz ≤ 230 feet (70 meters), HDBT Transmission Distance 4K@60Hz ≤ 131 feet (40 meters) Operation Temperature -5 to +55℃ (+23° to +131°F) Storage Temperature -25 to +70℃...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 3. Panel Description 3.1 Front Panel ① IR: Built-in IR sensor for receiving IR signals from IR remote to control the matrix. ② POWER: The LED illuminates green when the device is powered on, red when the device is in standby mode.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 3.2 Rear Panel ① INPUTS: Total six video inputs and three audio inputs. HDMI 1~4: Connects to HDMI source devices. ⚫ VGA: Connects to the VGA source. One stereo auxiliary audio input (3.5mm ⚫...
Page 10
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher AUDIO 2: Connects to audio playback device for audio de-embedding. The ⚫ audio output can be de-embedded from the HDBT or HDMI output selected via RS232 command. It’s de-embedded from HDMI output by default. ⑥...
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher 5. Button Control 5.1 Manual Switching When the switcher is in manual switching mode, the AUTO LED goes out. Please follow the below steps to switch input source to output channel. 1) Press any one of six input buttons to select input source, and the corresponding LED turns blue.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 5.3 Sound Volume Control Press volume knob to choose AUDIO 1 or AUDIO 2 audio needs to be adjusted, the corresponding LED will turn blue and keep on. Adjusting the knob in clockwise direction to increase sound volume. ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 6. IR Remote Control Connect IR receiver to the SYSTEM IR port, the switcher can be controlled by the following IR remote. ① Power on/off the switcher. ② Select input source. ③ Select output channel. ④...
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher 7. GUI Control The switcher can be controlled via TCP/IP. The default IP settings are: IP Address: 192.168.0.178 Subnet Mask: 255.255.255.0 Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage: Username: admin Password: admin Type the user name and password, and then click Login to enter the section for video...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.1 Switching Tab 7.1.1 Signal Switching HDBT OUTPUT: Select an input source for HDBT output. Click AUTO to ⚫ enable/disable auto switching mode. HDMI OUTPUT: Select an input source for HDMI output. Click AUTO to ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.2 Audio Tab AUDIO EMBEDDEDING: ⚫ ✓ Select the external LINE 1 or LINE 2 audio to be embedded in HDBT output. ✓ Select the external LINE 1 or LINE 2 audio to be embedded in HDMI output. AUDIO DE-EMBEDDEDING: ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.3 Configuration Tab 7.3.1 EDID Setting Select the compatible built-in EDID for the selected input source. ⚫ Upload user-define EDID by the below steps: ⚫ Step 1: Prepare the EDID file (.bin) on the control PC. Step 2: Select the user-defined.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.3.2 Scaling Setting Enable or disable HDBT output downscaling. The 4K video can be degraded to ⚫ 1080p output after enabling HDBT output downscaling. Enable or disable HDMI output upscaling. The 1080p video can be upgraded to 4K ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.4 CEC Tab If the input source devices and display devices support CEC, they can be controlled by the below control buttons to replace IR remote. 1) Input Source Control Select the input source which needs to be controlled, then press function buttons. ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.5 RS-232 Tab Select Local or HDBT Out control mode. ⚫ ✓ Local: Send RS232 commands to control the local third-party which is connected to the RS232 port of the switcher. ✓ HDBT Out: Send RS232 commands to remote via HDBT. Set the command format to HEX or ASCII.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.6 Interface Tab Title Bar Label: Modify the name of matrix switcher. ⚫ INPUT: Modify the label of input sources. ⚫ OUTPUT: Modify the label of outputs. ⚫ 7.7 Network Tab Static IP or Dynamic Host Configuration Protocol (DHCP). ⚫...
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 7.9 GUI Upgrade Please visit at http://192.168.0.178:100 for GUI online upgrade. Type the username and password (the same as the GUI log-in setting, modified password will be available only after rebooting) to login the configuration interface. After that, click Administration in the source menu, and then click Upload Firmware, select the desired update file and press Apply, it will start upgrading then.
4K 6x2 HDMI V2.0 HDBaseT Matrix Switcher 8. Auto-trigger CEC Both outputs can send power on or power off CEC commands to the TV automatically by detect source inputs. User can choose one output or both via RS232 command. Please refer to chapter 9.1 for more details. 8.1 Power on Command When the first source input is detected, the switcher will automatically send CEC command to turn on the TV.
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher 10. RS232 Control Connect the RS232 port to control device (e.g. PC) to control the switcher by RS232 commands, the RS232 command can also be forwarded to the receiver. RS232 commands can be used to control the unit via TCP/IP on port 23. RS232 Commands: The command lists are used to control the switcher.
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher 10.1 System Control Commands Command Example and Command Description Feedback Lock/ unlock front panel buttons. >SetKeyLock Off >SetKeyLock [Lockparam] = On, Off [Lockparam] On - Locked <KeyLock Off Off - Unlock Get the locking status of front panel >GetKeyLock <KeyLock Off buttons.
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher Command Example and Command Description Feedback 2: HDMI output 3: Both HDBT and HDMI outputs 4: No output >GetAutoTVPower Get the outputs of auto-trigger power >GetAutoTVPower on/off CEC command. <AutoTVPower 1 10.2 Signal Switching Commands Command Example and Command Description...
Page 30
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher Command Example and Command Description Feedback Set the switching priority in auto >SetSwitchPriority 06 05 04 >SetSwitchPriority switching mode. 03 02 01 [Prioparam1] [Prioparam1] ~ [Prioparam6] = 01~06 [Prioparam2] 01 = HDMI IN 1 [Prioparam3] 02 = HDMI IN 2 <AutoSwitchPriority 06 05 04...
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher Command Example and Command Description Feedback YPbPr: YPbPr signal >GetVGAVideoType >GetVGAVideoType Get video type of VGA input. <VGAVideoType VGA Set the resolution of VGA. >SetVGAOutResolution 01 >SetVGAOutResolution Resparam Resparam= 01,02,03,04,05,06 - 1920x1080 >SetVGAOutResolutio - 1920x1200 <VGAOutResolution n[Resparam]...
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher Command Example and Command Description Feedback S00 - Restore the output audio to the same source as the video. [Outputparam] = A01, A02, 01, 02, Null A01 - Output AUDIO 1 A02 - Output AUDIO 2 01 - The audio of HDBT output <Audio OUT A01 IN S01 02 - The audio of HDMI output...
4K 6X2 HDMI 2.0 HDBaseT Matrix Switcher 11. Firmware Upgrade Please follow the steps as below to upgrade firmware by the FIRMWARE port on the rear panel: 1) Prepare the latest upgrade file (.bin) and rename it as “FW_MERG.bin” on PC. 2) Power off the switcher, and connect the FIRMWARE port of switcher to the PC with USB cable.