Table of Contents
Advertisement
Quick Links
INSTALLATION & OPERATING MANUAL
Microframe Corporation
SERIES 200XXX4
Microframe Corporation
604 South 12th Street
Broken Arrow, OK 74012
Local: 918-258-4839
Toll Free: 800-635-3811
Website: www.microframecorp.com
E-mail: support@microframecorp.com
Manual No.
D0200XXX4-7010
Revision Date: 05/2024
Control: 2.0
Series 200XXX4
D0200XXX4-7010
*D0200XXX4-7010*
1
Advertisement
Table of Contents
Related Manuals for Microframe Corporation 200XXX4 Series
Summary of Contents for Microframe Corporation 200XXX4 Series
- Page 1 SERIES 200XXX4 INSTALLATION & OPERATING MANUAL Microframe Corporation 604 South 12th Street Broken Arrow, OK 74012 Local: 918-258-4839 Toll Free: 800-635-3811 Website: www.microframecorp.com E-mail: support@microframecorp.com Manual No. D0200XXX4-7010 Revision Date: 05/2024 Control: 2.0 D0200XXX4-7010 *D0200XXX4-7010* Microframe Corporation Series 200XXX4...
- Page 2 Your Microframe System is warranted against failure due to defects in workmanship or material for a period of one (1) year from the date of purchase. Microframe Corporation will repair or replace any defective unit. Obvious abuse or mishandling of the unit is NOT covered by this warranty.
-
Page 3: Table Of Contents
Series 200XXX4 Installation and Specification Guide Table of Contents Overview Installation Configuration Programmable Options Module Calibration Factory Reset Appendix A – Troubleshooting Specifications Microframe Corporation Series 200XXX4... -
Page 4: Overview
Follow the instructions in Configuration (next page) to configure the module. Mounting The indoor and outdoor version of these displays mount using the tilt-mount brackets attached to the sides of the display. Each bracket has a flange with two screw holes for wall mounting. Microframe Corporation Series 200XXX4... -
Page 5: Configuration
To set the minimum display value, have your sensor output the minimum value (typically 4mA). On the settings webpage, set the Min value to match the Current value. Set Range Set the start and end values of your Display Range. Microframe Corporation Series 200XXX4... -
Page 6: Programmable Options
Round Value by – Round the displayed value to hide small variations. [Reset to Defaults] – press this to reset the settings on this page to the defaults. [Reboot] – Reboot the product. You may need to reconnect your device to the SoftAP network. Microframe Corporation Series 200XXX4... -
Page 7: Module Calibration
Turn the (right) span pot just until the ‘Current’ value shows 65535. Set ‘Filter Time’ back to the previous value and click ‘Set’. Factory Reset To reset the display hardware to Factory Defaults, press and hold the mode button for 20 seconds. Microframe Corporation Series 200XXX4... -
Page 8: Appendix A - Troubleshooting
TROUBLESHOOTING CHART SYMPTOM POSSIBLE SOLUTION CAUSE Display is blank No power to unit Make sure the unit is plugged in and the and no Processor outlet is working. Unit is dead Return unit to Microframe for servicing. Microframe Corporation Series 200XXX4... -
Page 9: Box Contents
Power Requirements 6.5 watts 7.7 watts 9.9 watts 3.0 lbs 4.2 lbs 4.5 lbs Display Weight, w/o adapter (1.4 kg) (1.8 kg) (1.9 kg) 13.2" 16.8" 18.4" Width "A" Dimension (33.5 cm) (42.7 cm) (46.7 cm) Microframe Corporation Series 200XXX4...
Need help?
Do you have a question about the 200XXX4 Series and is the answer not in the manual?
Questions and answers