Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dini Argeo DFWX Series
Summary of Contents for Dini Argeo DFWX Series
- Page 1 DFWX SERIES ENGLISH SHORTCUT QUICK REFERENCE GUIDE www.diniargeo.com...
- Page 2 © Dini Argeo. All rights reserved. Dini Argeo® is a registered trademark. Dini Argeo owns the copyright for the contents of this document (including artwork, illustrations, photographs, and written material). You may not copy, reproduce, modify, republish, or distribute any material from this document without permission.
-
Page 3: Table Of Contents
CONTENTS INTRODUCTION F MODE DISABLE FUNCTION MODE ENABLE FUNCTION MODE ENABLE FUNCTION MODE WHEN PIN IS SET SHORTCUTS GENERAL SHORTCUTS WEIGHING MODE SHORTCUTS RESET SHORTCUTS USER MENU (F Modes 1 - 20) CHECK WEIGH MODE SHORTCUTS ( F Modes 101 - 113) TOTALIZATION SHORTCUTS ( F Modes 201 - 207) COUNTING SHORTCUTS ( F Modes 301 - 304) CALIBRATION SHORTCUTS (F Modes 1001 - 1004) -
Page 4: Introduction
Introduction INTRODUCTION The purpose of this document is information on shortcuts available with the DFWX. The DFWX provides several shortcuts that access specific functions typically found in the user configuration menu. The shortcuts are activated by pressing the F key in combination with various keys on DFWX models. -
Page 5: F Mode
F Mode F MODE The F (Function) mode must be used when entering shortcuts. This section describes how to enable or disable F modes. The following shortcuts can be used if the F key is disabled: • F + ZERO •... -
Page 6: Enable Function Mode When Pin Is Set
F Mode ENABLE FUNCTION MODE WHEN PIN IS SET 1 0.000 pin . use 10 sec. Enab Enter the user PIN. Store DFWX... -
Page 7: Shortcuts
Shortcuts SHORTCUTS This section lists Function (F) Mode shortcuts with brief descriptions. GENERAL SHORTCUTS Shortcut Parameter Description Opens Back light Intensity configuration menu (oFF brGt 0 through brGt F + ZERO brGt Opens preset tare configuration menu F + TARE NOTE: This shortcut provides the same functionality as configuring the preset TARE. -
Page 8: User Menu (F Modes 1 - 20)
Shortcuts USER MENU (F Modes 1 - 20) Shortcut Parameter Description Opens Tare in memory configuration menu. Select tare value from Tare's 1 + F tp n Database, only if tare database is active (17 + F) 2 + F ii dn1 Enable”... -
Page 9: Check Weigh Mode Shortcuts ( F Modes 101 - 113)
Shortcuts CHECK WEIGH MODE SHORTCUTS ( F Modes 101 - 113) Shortcut Parameter Description Opens Check Mode Type configuration menu (GroSS, t.nEt, ZEro, nEG. or oFF) 101 + F Type NOTE: This shortcut provides the same functionality as the F + TARGET shortcut. 102 + F C.Mode Opens Tolerance Mode configuration menu (toLEr, AbSoL, or t.PErC) -
Page 10: Totalization Shortcuts ( F Modes 201 - 207)
Shortcuts TOTALIZATION SHORTCUTS ( F Modes 201 - 207) Shortcut Parameter Description Opens Totalisation type configuration menu (LoAd, unLoAd or oFF) 201 + F en.tot NOTE: This shortcut provides the same functionality as the F + M+ shortcut. Opens Maximum total configuration menu (the maximum quantity of totalizations). -
Page 11: Calibration Shortcuts (F Modes 1001 - 1004)
Shortcuts CALIBRATION SHORTCUTS (F Modes 1001 - 1004) Shortcut Parameter Description 1000 + F Opens Quick calibration 1001 + F Cal.adv Opens Advanced calibration Opens Calibration adjustment. It calibrates the zero point and span in 1002 + F Cal.adj different times (typically required during silo calibration) 1003 + F 0.Cal Zeros Calibration... - Page 12 NOTES DFWX...
- Page 13 NOTES DFWX...
- Page 14 NOTES This publication, or portions thereof, may not be duplicated without written permission from the Manufacturer. All information contained in this manual is based on the data available at the time of its publication; the Manufacturer reserves the right to make changes to its products at any time without notice and without incurring any penalty.
-
Page 16: Service Assistance
Stamp of the authorized service center HEAD OFFICE Via Della Fisica, 20 41042 Spezzano di Fiorano, Modena - Italy Tel. +39.0536 843418 - Fax. +39.0536 843521 info@diniargeo.com SERVICE ASSISTANCE Via Dell’Elettronica, 15 41042 Spezzano di Fiorano, Modena - Italy Tel. +39.0536 921784 - Fax. +39.0536 926654 service@diniargeo.com...
Need help?
Do you have a question about the DFWX Series and is the answer not in the manual?
Questions and answers