LEGRAND VANTAGE LVOS-0-10-PWM-DIN Installation Instructions
LEGRAND VANTAGE LVOS-0-10-PWM-DIN Installation Instructions

LEGRAND VANTAGE LVOS-0-10-PWM-DIN Installation Instructions

Radiolink keypad station

Advertisement

No: IS-0521 – rev. 3 9/23
LVOS-0-10-PWM-DIN • Les Numéros de Catalogue • Los Números de Catálogo:
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
STATION
1
2
3
4
BUS
IR
SENS
COMMERCIAL DIMMERS
CLASS 2
50mA
2K21
CONTACT INPUTS
MAX
1
2
3
4
RED = 0-10
GREEN = PWM
LOW VOLTAGE OUTPUT STATION-0-10-PWM-DIN
1
2
3
4
5
INPUT
13.8-36
VDC
8, independent 0-10V low-voltage outputs
Outputs 1-4 can be configured as PWM or 0-10V
Manual control and LED status for all 8 LV outputs on front
High resolution performance when dimming
Communicates via Station Bus
Assembled in a 9 unit DIN case
Override switch for ON and OFF states of all loads
CE Certification / UL
Dimensions, HWD
Weight
LED Indicators
Ambient Operating Temperature
Relative Humidity
Cooling
Firmware
Manual Control
FreeRTOS
Compliance
No: IS-0521 – Rev. 3
STATION
SERIAL NUMBER
BUS
CLASS 2
OVERRIDE
5
6
7
8
STATUS
6
7
8
LVOS-0-10-PWM-DIN
0-10: 10VDC@100mA MAX
PWM: 12VDC@100mA MAX
FEATURES AND OPERATIONS OVERVIEW
RadioLink Keypad Station
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
The DIN Rail mounted Low Voltage Output Station (LVOS) is used for the
control and automation of LED and Fluorescent lighting loads requiring either
0-10V or pulse width modulation (PWM) for dimming control. The DIN LVOS
can control up to eight 0-10V loads. Unlike other LVOS products the DIN
LVOS does not have relays on-board for switching. It relies on an external
relay station (RS8-L-DIN) or module (MDR8CW301) to do high-voltage
switching. The dry contact inputs on the station can be used with motion
sensors, light sensors, optical switches, magnetic switches, and more. As part
of the Legrand Architectural Dimming lighting solution, it provides control of
lighting loads as well as inputs from dry contacts for lighting and automation.
SPECIFICATIONS
General
85.7mm x 157.2mm x 61.9mm (3.38" x 6.19" x 2.44")
237g (8.36oz)
Microprocessor status, configuration, loads
LED on loads 1-4: Red = 0-10 / GREEN = PWM
32-104°F (0-40° C)
Maximum 90%, non-condensing
Convection
Upgradeable via Station Bus
Overlay with control/status for each output
Real-time scheduling provided by FreeRTOS (www.freertos.org)
UKCA, UL, cUL, RoHS, CE, FCC, EN 55032, EN 55035, EN 61000-3-2,
EN 61000-3-3
1
OVERVIEW

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VANTAGE LVOS-0-10-PWM-DIN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for LEGRAND VANTAGE LVOS-0-10-PWM-DIN

  • Page 1 The dry contact inputs on the station can be used with motion sensors, light sensors, optical switches, magnetic switches, and more. As part LVOS-0-10-PWM-DIN INPUT of the Legrand Architectural Dimming lighting solution, it provides control of 0-10: 10VDC@100mA MAX 13.8-36 PWM: 12VDC@100mA MAX lighting loads as well as inputs from dry contacts for lighting and automation.
  • Page 2: Specifications

    SPECIFICATIONS DC Input - Power Supply Input Voltage 13.8 - 36VDC Input Power Draw <15W Connection Type 0.20” pitch removable plug Connection Rating 300V 10A Relative Humidity Maximum 90%, non-condensing Input / Output Connections (Low-voltage) Station Bus Connection 24V/36V Station Bus Station Bus Wiring Specification 2C, 16AWG / 1.31mm2, twisted, non-shielded, <30pF per foot.
  • Page 3: Load Configurations

    LOAD CONFIGURATIONS Setting up the load configurations, as shown below, is done in Design Center software. Only loads 1-4 may be configured as PWM. Set all four loads as PWM or in sets of two (loads 1 and 2, or loads 3 and 4) 8 Loads 0-10V (Factory Default) 2 Loads PWM 6 Loads 0-10V...
  • Page 4: Button Operation

    POWER CONNECTION Connect the 13.8 – 36VDC power feed. Legrand recommends the PSU36-DIN 36VDC (CE only) or ACPDXXSM2 24VDC power supplies*. This provides power for the LVOS-0-10-PWM-DIN and is required for the station to operate. Use 16AWG / 1.31mm2 wire between power supply and stations using a daisy-chain topology.
  • Page 5: Diagnostic Led Information

    No. IS-0521 – rev. 3 9/23 © Copyright 2023 Legrand All Rights Reserved. 800.555.9891 © Copyright 2023 Tous droits réservés Legrand. www.legrand.us/vantage © Copyright 2023 Legrand Todos los derechos reservados.

Table of Contents