Table of Contents
Related Manuals for Char-Broil 463322013
Summary of Contents for Char-Broil 463322013
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Charbroil 463322013 Owner's Manual Shop genuine replacement parts for Charbroil 463322013 Find Your Charbroil Grill Parts - Select From 3621 Models -------- Manual continues below part list --------...
- Page 2 Available Replacement Parts for Charbroil 463322013 G430-0033-W1 Grease Cup Aluminized. Measures approxim G508-0039-W1 Match Holder And Chain. G401-0086-W2 Logo Plate. Thermos g409-0030-w1 Button For Electronic Module. Measures a g431-0300-w2A Burner Tube Stainless Steel (R g413-0004-w2 Flame Carry Over Tube G430-0005-W1...
- Page 3 ASSEMBLY Place bottom shelf with cut out hole for LP tank next to legs with axle holes. Attach to right and left leg assemblies with 1/4-20x1-1/2" screws and 1/4-20 flange nuts. Left Leg Assembly Bottom Shelf Right Leg Assembly Axle Hole 1/4-20 1/4-20x1-1/2"...
- Page 4 Insert the straight end (without hole) of the short tank exclusion wire into the hole on right front leg. Attach the other end (with ASSEMBLY hole) to right rear leg with #8x3/8" sheet metal screw, as shown (A). Insert the straight end (without hole) of the long tank exclusion wire into the hole on right front leg. Attach the other end (with hole) to bottom shelf with #8x3/8"...
- Page 5 Stand cart upright. This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Attach with 1/4-20x1/2" machine screws 1/4-20x1/2" Grill Head Machine Screw Qty: 4...
- Page 6 Hook side wall of shelf over support brackets on side of firebox. At back of firebox, insert 7x15 fiber washer and 1/4-20x1/2" machine screw as shown (A). Inside firebox insert 7x15 fiber washers and 1/4-20x1/2" machine screws as shown (B). Attach shelf with 1/4-20 flange nuts on each side (C).
- Page 7 Hook side wall of sideburner shelf over support brackets on side of firebox. At back of firebox, insert 7x15 fiber washer and 1/4-20x1/2" machine screw as shown (A). Inside firebox insert 7x15 fiber washers and 1/4-20x1/2" machine screws as shown (B). Attach sideburner shelf with 1/4-20 flange nuts on each side (C).
- Page 8 Position side burner valve bracket beneath side burner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure with #8-32x3/8" Stainless Steel screws (A). Place side burner into shelf.
- Page 9 Place heat tents over burners by inserting tabs into slots in front of firebox. Opposite ends of heat tents rest on pins in back of firebox. Place cooking grates onto grate rests. Unscrew ignitor cap and place AA battery into ignitor slot with positive end (+) facing outward. Replace ignitor cap onto ignitor. Cooking Grate AA Battery...
- Page 10 Hang grease cup clip from bottom of firebox and place grease cup into grease cup clip. Grease Cup Clip Grease Cup CAUTION Failure to install grease cup clip and cup will cause hot grease to drip from bottom of grill with risk of fire or property damage. LP tank is sold separately.
-
Page 11: Troubleshooting
DANGER: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from • Damaged hose. • Turn off gas at LP cylinder or at source on natural gas systems. If cracked/cut/burned anything but burned, replace valve/hose/regulator. -
Page 12: Electronic Ignition
Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not light ELECTRONIC IGNITION: using ignitor. • No spark, no ignition noise. • See Section I of Electronic Ignition System. (See Electronic Ignition Troubleshooting also) • No spark, some ignition noise. • See Section II of Electronic Ignition System. •... -
Page 13: Troubleshooting - Electronic Ignition
Troubleshooting - Electronic Ignition Problem (Ignition) Possible Cause Check Procedure Prevention/Solution SECTION I No sparks appear at • Battery not installed • Check battery orientation. • Install battery (make sure that “+” and “–” any electrodes when properly. connectors are oriented correctly, with “+” end up Electronic Ignition Button and “–”...
Need help?
Do you have a question about the 463322013 and is the answer not in the manual?
Questions and answers