Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Yolin YL61F-F
Summary of Contents for Yolin YL61F-F
- Page 1 Electric Bike Display User’s Manual YL61F-F Tianjin Yolin Technology Co. Ltd.
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Product name and model ................................1 2. Specifications ................................... 1 3. Appearance and dimensions ..............................1 4. Function overview and Functional areas ..........................2 4.1 Functional overview ...............................2 4.2 Functional areas ................................2 4.3 Button definitions ................................2 5. Routine operation ..................................2 5.1 Power on/off ................................... -
Page 3: Product Name And Model
● Working current at the supply controller end 50mA ● Working temperature -10～60℃ ● Storage temperature -30～70℃ 3. Appearance and dimensions Fig. 3-1 Picture of Display YL61F-F Fig. 3-2 Top View of Display YL61F-F Dimensions Fig.3-3 Side View of Display YL61F-F Dimensions... -
Page 4: Function Overview And Functional Areas
Trip Odometer Max speed Average speed Figure 4-1 YL61F-F functional area distribution interface 4.3 Button definitions The YL61F-F display is equipped with three buttons on the corresponding operating unit: power on/off , plus minus 5. Routine operation 5.1 Power on/off Long press to power on / off the display. -
Page 5: Display Interface Switching
5.2 Display interface switching When the display is powered on, it will show the Current Speed (mile/h) and Trip Odometer (mile) by default. Short press to switched cyclically between Trip Odometer (mile), Odometer (mile), Maximum Speed (mile/h), Average Speed (mile/h) ,Voltage(V) , and Current(A). Trip odometer Odometer Current... -
Page 6: Reverse Mode
5.3 Reverse mode When the assist gear is in 0 gear,long press and hold , the electric bicycle enters the reverse mode and the display shows . Release the button to stop the power output immediately and restore to the state before reverse. Figure 5-2 reverse mode display interface 5.4 Turning on/off lights Long press the... -
Page 7: Pas Level Selection
5.5 PAS level selection Press to switch PAS level of electric bicycle, thus changing the motor output power. (The following pictures are only for illustration of different speeds in different gears. The specific speed is subject to the actual product) Figure 5-4 PAS level display interface 5.6 Battery level display The Battery level is shown as 5 bars. -
Page 8: Personalized Parameter Settings
6. Personalized parameter settings The setting needs to be done with the bicycle stationary. The personalized parameter setting procedure is as follows: When the display is ON and the speed shows 0, (1) Press and hold simultaneously for more than 2 seconds to enter the personalized parameter setting interface. -
Page 9: Pas Level Setting
6.2 PAS level setting 02P is the Pedal assist (PAS) level setting. The available Pedal assist level settings are: 0~3, 1~3, 0~5, 1~5, 0~7, 1~7, 0~9, 1~9. Press to enter the parameter changing state. Press the to select the parameter and press to save the parameter setting and enter the 6.2.1 PAS level ratio value setting interface, or press and hold the to confirm and return... -
Page 10: Pedal Assist Sensitivity Setting
6.3 Pedal assist sensitivity setting 03P is the pedal assist sensitivity setting. When set to higher numbers, it will take more crank rotations to activate the motor. On lower numbers, it will take little crank rotation to activate the motor. The adjustable range is: 2~9, 2 is the highest level sensitivity while 9 is the lowest. -
Page 11: Power-On Password Setting
6.5 Power-on password setting 05P is the power-on password setting. The power-on password is not activated by default but users can activate it from setting PSd-y. The factory default password is 1212. Users can set other four-digit password. Please keep the password in mind after changing it, otherwise you will not be able to use the display! Press to enter the parameter changing state. -
Page 12: Auto Sleep Time Setting
6.6 Auto sleep time setting 06P is the auto sleep time setting. To save the battery power and reach higher range, this display will be turned off after it has not been used for a time. The adjustable range is: 00~60min, 00 means no auto shutdown. The factory default setting is 10 minutes. -
Page 13: Speed Limit Setting
6.8 Speed limit setting In the personalized parameter setting interface, press and hold simultaneously for more than 2 seconds to enter speed limit adjustment mode. The adjustable range is: SP-N and SP-S (25km/h and 51km/h). (The maximum adjustable speed limit varies by different protocols). Press to enter the parameter changing state. -
Page 14: Shortcut Operation
7. Shortcut operation 7.1 Restore factory default parameter settings operation dEF is the restore factory default parameter settings. dEF-Y is the restore the factory default settings, and dEF-N is not to restore. Enter into the main setting interface and keep the speed at 0, press and hold simultaneously for 2s to enter the restore factory default setting interface. -
Page 15: Quality Assurance And Warranty
8. Quality Assurance and Warranty 8.1 Warranty info ● Yolin will offer a limited warranty for any failure caused by the product defects under normal use during the warranty period. ● The product is warranted for 12 months from the date out of factory. -
Page 16: Schedule 1: Error Code Definition
0-3/1-3 100% 0-5/ 1-5 0-7/ 1-7 0-9/ 1-9 Tel: 022-86838795 Fax: 022-86838795 Email: yolin@yolintech.com Website: www.yolintech.com Address: Tianjin Beichen District, Tianjin Beichen Economic Development Zone, Medical Equipment Industrial Park, East of Jingfu Highway, Ugu New Science Park 52-1 plant...
Need help?
Do you have a question about the YL61F-F and is the answer not in the manual?
Questions and answers