Summary of Contents for Better Homes and Gardens Juliet BH3425004710020
Page 1
LOT NUMBER: DATE PURCHASED: Juliet Arch Open Bookcase Stock # BH3425004710020 # BH3425004710054 # BH3425004710055 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 1-866-942-5362 Pacific Standard Time: 8:30 a.m.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S MANUFACTURER: Whalen Furniture Manufacturing CATALOG : Juliet Arch Open Bookcase MODEL # BH3425004710020 / BH3425004710054 / BH3425004710055 MAXIMUM LOAD 22.7 kg / 50 lb.
Page 3
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH.
Page 4
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Left Side Panel B- Right Side Panel (Qty. 1) (Qty. 1) C- Upper Fixed Shelf D - Lower Fixed Shelf (Qty.
Page 5
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. K- Bottom Middle Stretcher L- Lower Back Panel (Qty. 1) (Qty. 1) M- Upper Back Panel N- Try Square (Qty.
Page 6
Assembly Instructions ② x 12 NOTE: Please do not fully tighten all cam locks and bolts until you finish assembling all parts. Once assembled, go back and fully tighten all cam locks and bolts. This will make the assembly easier. 1.
Page 7
Assembly Instructions ② x 12 3. Securely screw the Cam Bolts (2) into the designated small holes on the Upper Fixed Shelf (C) and Bottom Panel (E) using a Phillips screwdriver.
Page 8
Assembly Instructions ③ x 12 4. Glue the Wood Dowels (3) into the inner holes on the Fixed Shelves (C and D) and Bottom Panel (E). NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the excess glue immediately with a damp cloth.
Page 9
Assembly Instructions Raw edge ① x 2 5. Orient and attach the Upper Fixed Shelf (C) to the Left Side Panel (A) by engaging 2 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts. (Refer to page 3 on Cam Lock system operation supplement).
Page 10
Assembly Instructions ① x 2 The cam lock housings face the floor when the unit is turned upright. 6. Align and attach the Lower Fixed Shelf (D) to the Left Side Panel (A) by engaging 2 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts.
Page 11
Assembly Instructions The pilot holes face up. ① x 2 Cam lock housings face outward. 7. Orient and attach the Bottom Panel (E) to the Left Side Panel (A) by engaging 2 Cam Locks (1).
Page 12
Assembly Instructions C/D/E ① x 6 8. Repeat the previous process to attach the Right Side Panel (B) at the opposite end.
Page 13
Assembly Instructions ③ x 6 9. Glue six Wood Dowels (3) into the inner holes on both Arches (G and H).
Page 14
Assembly Instructions ⑦ x 2 10. Combine the assembled arches with the middle wood dowels fully inserted. 11. Insert two 45 mm Bolts (7) through the mounting holes on the Right Arch (H) and finger tighten into the Left Arch (G). DO NOT securely tighten the bolts.
Page 15
Assembly Instructions ① x 4 12. Orient and position the assembled arch onto both Side Panels (A and B) and tighten with 4 Cam Locks (1). 13. Go back and securely tighten the two 45 mm Bolts (7) installed in step 11 with the hex wrench provided.
Page 16
Assembly Instructions ② x 6 14. Securely screw the Cam Bolts (2) into the designated small holes on both Bottom Side Frames (I) using a Phillips screwdriver.
Page 17
Assembly Instructions ③ x 10 15. Glue 10 Wood Dowels (3) into the holes run against cam bolt cross bore on the Bottom Stretchers (J and K).
Page 18
Assembly Instructions The cam lock housings facing inward. ① x 6 16. Orient and attach both Bottom Stretchers (J and K) to one Bottom Side Frame (I) with 3 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts. Ask for assistance to hold each stretcher and ensure it is flush with the side frame before tightening cam locks.
Page 19
Assembly Instructions Try Square I /J ① x 8 18. Align and attach the assembled base to the Bottom Panel (E) by engaging 8 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts. 19.
Page 20
Assembly Instructions The adhesive tape face outward. 1 mm ④ x 22 1 mm 20. Now, go back and securely tighten all the Cam Locks and Bolts. Make sure that all the parts are tight and there are no gaps between them. This will help to keep the unit square. 21.
Page 21
Assembly Instructions 1 mm 1 mm ④ x 8 23. Align the mounting holes on the top edge of Upper Back Panel (M) with the pilot holes on the rear edge of the Arch Assemblies (G and H) properly, loosely fasten with two 15 mm Washer Head Screws (4). Make sure that the margins along both side edges are approximately 1 mm.
Page 22
Assembly Instructions ⑤ x 12 24. Ask for assistance to lift the assembled unit upright and position it near the final location. 25. Insert the Shelf Supports (5) into the holes at your desired height. Make sure you place the four Shelf Supports (5) at the same level to level the shelf.
Page 23
Assembly Instructions x 12 ⑥ 26. Insert the Cam Lock Covers (6) onto the visible cam locks to conceal the cams.
Page 24
Assembly Instructions Wooden stud Wall Wall Metal bracket Long screw Short screw Connector Floor leveler Steel cable Wall Tools required (not included): Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit. 27. Ask for assistance to position the assembled unit at the desired location against a wall. If necessary, adjust the installed floor levelers to correct the tilting.
Page 25
FURNITURE TIPPING RESTRAINT YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES. THIS HARDWARE, MUST BE PROPERLY INSTALLED (FOLLOW ALL DIRECTIONS IN ORDER ON THIS INSTRUCTIONS), TO PROVIDE PROTECTION AGAINST THE UNEXPECTED TIPPING OF FURNITURE DUE TO IMPROPER USE.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. ...
Page 27
NÚMERO de LOTE: FECHA de COMPRA: Librero de arco abierta Juliet Serie # BH3425004710020 # BH3425004710054 # BH3425004710055 ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compro.
Page 28
M Á X I M O P E S O R E C O M E N D A D O FABRICANTE: Whalen Furniture Manufacturing CATALOGO : Librero de arco abierta Juliet MODELO # BH3425004710020 / BH3425004710054 / BH3425004710055 CARGA MÁXIMA 22.7 kg / 50 lb. ADVERTENCIA ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS INDICADOS.
Page 29
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá las partes identificadas en la página 4 y 5 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE EL USO DE GOMA CON LAS CLAVIJAS DE MADERA.
Page 30
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. A- Panel izquierdo B- Panel derecho (Cant. 1) (Cant. 1) C- Repisa superior fija D- Repisa inferior fija (Cant.
Page 31
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. K- Soporte inferior medio L- Panel posterior superior (Cant. 1) (Cant. 1) M- Panel posterior inferior M- Escuadra (Cant.
Page 32
Instructivo de ensamble ② x 12 NOTA: Por favor no apriete completamente todos los pernos, hasta que termine con el ensamble de las partes. Después, asegúrese de apretar todos los pernos. Esto hará el ensamble más fácil. 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños.
Page 33
Instructivo de ensamble ② x 12 3. Atornillar a los pernos de fijación (2) en los agujeros pequeños designados en la repisa superior fija (C) y el panel inferior (E) usando el desarmador estrella.
Page 34
Instructivo de ensamble ③ x 12 4. Pegar las clavijas de madera (3) en los agujeros internos en las repisas fijas (C y D) y en el panel inferior (E). NOTA: Es importante usar una cantidad pequeña de pegamento en ambos lados de las clavijas y limpiar el exceso de pegamento inmediatamente con una toalla húmeda.
Page 35
Instructivo de ensamble Borde sin acabado ① x 2 5. Orientar y adjuntar la repisa superior fija (C) al panel izquierdo (A) empleando dos tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación. (Consulte la página 3 del sistema de tuerca de fijación).
Page 36
Instructivo de ensamble ① x 2 Los espacios de las tuercas de fijación apuntan hacia el piso cuando la unidad esté en posición vertical. 6. Alinear y adjuntar la repisa inferior fija (D) al panel izquierdo (A) empleando dos tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación.
Page 37
Instructivo de ensamble Los agujeros pilotos quedan hacia arriba. ① x 2 Los espacios de las tuercas de fijación apuntan hacia afuera. 7. Orientar y adjuntar el panel inferior (E) al panel izquierdo (A) empleando dos tuercas de fijación (1).
Page 38
Instructivo de ensamble C/D/E ① x 6 8. Repetir el proceso previo para adjuntar el panel derecho (B) al extremo opuesto.
Page 39
Instructivo de ensamble ③ x 6 9. Pegar 6 clavijas de madera (3) en los agujeros internos en ambos arcos (G y H).
Page 40
Instructivo de ensamble ⑦ x 2 10. Combinar los arcos ensamblados con las clavijas de madera medias insertadas completamente. 11. Insertar dos pernos de 45 mm (7) a través de los agujeros de montaje en el arco derecho (H) y apriételos con los dedos en el arco izquierdo (G).
Page 41
Instructivo de ensamble ① x 4 12. Orientar y poner el arco ensamblado sobre ambos paneles laterales (A y B) y apretar con 4 tuercas de fijación (1). 13. Vuelva atrás y apriete firmemente los dos pernos de 45 mm (7) instalados en el paso 11 con la llave hexagonal proporcionado.
Page 42
Instructivo de ensamble ② x 6 14. Atornillar los pernos de fijación (2) en los agujeros pequeños designados en ambos marcos inferiores laterales (I) usando el desarmador estrella.
Page 43
Instructivo de ensamble ③ x 10 15. Pegar 10 clavijas de madera (3) en los agujeros designados en los soportes inferiores (J y K), como se muestra.
Page 44
Instructivo de ensamble Los espacios de las tuercas de fijación apuntan hacia adentro ① x 6 16. Orientar y adjuntar ambos soportes inferiores (J y K) a un marco inferior lateral (I) con 3 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación. Pedir asistencia para levantar cada soporte y asegurar que esté...
Page 45
Instructivo de ensamble Escuadra I /J ① x 8 18. Alinear y adjuntar la base ensamblada al panel inferior (E) empleando 8 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación. 19.
Page 46
Instructivo de ensamble Las cintas adhesivas apuntan hacia afuera. 1 mm ④ x 22 1 mm 20. Ahora, volver y apretar todas las tuercas de fijación y los pernos. Asegurar que todas las partes estén apretadas y de que no hay huecos entre las partes. Esto ayudara a mantener la unidad cuadrada. 21.
Page 47
Assembly Instructions 1 mm 1 mm ④ x 8 23. Alinee los orificios de montaje en el borde superior del panel posterior superior (M) con los orificios guía en el borde posterior de los conjuntos de arco (G y H) correctamente, sujetar flojamente con dos pernos de cabeza de arandela de 15 mm restantes (4).
Page 48
Instructivo de ensamble ⑤ x 12 24. Pedir asistencia para poner la unidad ensamblada en posición vertical y cerca de la posición final. 25. Insertar los soportes para repisa (5) en los agujeros a su altura deseada. Asegurar de poner cuatro soportes para repisa (5) en el mismo nivel para nivelar la repisa.
Page 49
Instructivo de ensamble x 12 ⑥ 26. Insertar las tapas de las tuercas de fijación (6) sobre las tuercas de fijación visibles para esconder.
Page 50
Instructivo de ensamble Viga de madera Pared Pared Soporte de metal Perno largo Perno corto Conector Nivelador de piso Cable de acero Pared Herramientas requeridas (no incluidas): Desarmador estrella, buscador de vigas, cinta métrica, lápiz, taladro y broca de 1/8 pulgadas. 27.
Page 51
SISTEMA DE RESTRICCIÓN DE MOVIMIENTO NIÑOS PEQUEÑOS PUEDEN RESULTAR LASTIMADOS POR MUEBLES INCLINADOS Y DEBE INSTALAR EL JUEGO DE RESTRICCIÓN DE MOVIMIENTO CON LA UNIDAD EN FUNCIÓN, PARA PREVENIR LA INCLINACIÓN DE LA UNIDAD, CAUSANDO CUALQUIER ACCIDENTE O DAÑO. ESTÉ JUEGO DEBE SE INSTALADO CORRECTAMENTE (SIGA LAS DIRECCIÓN EN ORDEN DE LAS INSTRUCCIONES), PARA PROVEER PROTECCIÓN EN CONTRA DE LA INCLINACIÓN INESPERADA DEL MUEBLE DEBIDO AL USO INAPROPIADO.
Page 52
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruébela en un área que no sea visible para revisar su funcionamiento. ...
Need help?
Do you have a question about the Juliet BH3425004710020 and is the answer not in the manual?
Questions and answers