Related Manuals for TOLSEN TOOLS FX 79791
Summary of Contents for TOLSEN TOOLS FX 79791
- Page 1 79791 HOT AIR GUN INSTRUCTION MANUAL 120V~ 12.5Amp (1500W) SAVE THIS MANUAL ! You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference.
-
Page 2: Important Safety Information
SAFETY IMPORTANT SAFETY INFORMATION General Power Tool Safety Warnings WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ”power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 3 SAFETY 11. Stay alert, watch what you are doing and use ANSI-approved and breathing protection must common sense when operating a power tool. be NIOSH-approved for the specific hazards in Do not use a power tool while you are tired or the work area.
- Page 4 SAFETY tool for operations different from those qualified repair technicians at an authorized intended could result in a hazardous situation repair center. Improperly repaired tools could 26. SERVICE AND REPAIRS should be made by cause serious shock or injury. Hot Air Gun Safety Warnings 1.
- Page 5 SAFETY • Wear a dust respirator mask or a dual filter (dust prepared for flames to develop and keep and fume) respirator mask which has been suitable fire extinguishing means at hand. approved by the Occupational Safety and 6. The Nozzle becomes very hot. Do not lay the Health Administration (OSHA), the National Heat Gun on flammable surfaces when Institute of Safety and Health (NIOSH), or the...
-
Page 6: Specifications
SAFETY AND SPECIFICATIONS & SETUP SPECIFICATIONS Electrical Input 120 VAC / 60 Hz Low: 6.25A(750W) High: 12.5A(1500W) Adjustable Heat Setting Type Three-Way Rocker Switch(I,O,II) Heat Temperatures Low : 572°F /300°C(Maximum) 4002205 High : 1112°F /500°C(Maximum) Air Flow Low : 280 L/min High : 480 L/min Note: Symbology Double Insulated... - Page 7 SETUP Applications When observing the safety rules, this Heat Gun is designed for all applications with hot air that are listed below: • Shrinking of heat shrink tubing, solder • Drying of color shade samples, filter, connectors and solder terminals, packaging and adhesives, construction joints and stucco forms.
-
Page 8: Tool Set Up
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Tool Set Up WARNING: TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before adjusting tool or installing accessories. General Operating Instructions 1. -
Page 9: Maintenance And Servicing
MAINTENANCE AND SERVICING MAINTENANCE AND SERVICING WARNING: TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the switch and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. -
Page 10: Troubleshooting
MAINTENANCE AND SERVICING & PARTS LIST Troubleshooting Problem Possible Causes Likely Solu�ons Heat Gun will 1. Power Switch set at “0”. 1. Turn Power Switch to “l” or “ll”. not turn on. 2. No power at outlet. 2. Check power at outlet. 3. - Page 11 SUZHOU TOLSEN TOOLS CO.,LTD. www.tolsentools.com TOLSEN is a trademark or registered trademark of TOLSEN TOOLS. All rights reserved. SCAN TO VISIT TolsenWorld MADE IN CHINA PRODUCT LINK...
Need help?
Do you have a question about the FX 79791 and is the answer not in the manual?
Questions and answers