LOFT GO! 7D EQ About this manual Scope Legend This manual contains parts diagrams, specifications (such as grease and torque values), instructions, and Cable (zip) tie helpful tips. It does not contain instructions for all components (such as brake calipers). Refer to the original manufacturer for more information.
LOFT GO! 7D EQ Hub motor 42Nm 42Nm Remove the rear wheel Lock nut (non-drive side) Before removing the wheel, follow the steps below. Anti-rotational washer (non-drive side) Shift to the smallest rear cog (highest gear). 5260931 Unplug the motor cable at the chainstay. Anti-rotational washer (drive side) Cut the rear zip (cable) tie on the driveside chainstay.
Page 8
LOFT GO! 7D EQ Bottom bracket/torque sensor 35Nm 35Nm Non-driveside cup Driveside cup W5257770 Torque sensor...
Page 9
LOFT GO! 7D EQ Bottom bracket/torque sensor: remove AUTHORIZED DEALERS ONLY: Only authorized dealers should perform service on the e-system. Improper handling, tools used, or torque applied to these parts may result in damage to the e-system components and cables. Remove the bottom bracket cover.
Page 10
LOFT GO! 7D EQ Bottom bracket/torque sensor: install AUTHORIZED DEALERS ONLY: Only authorized dealers should perform service on the e-system. Improper handling, tools used, or torque applied to these parts may result in damage to the e-system components and cables. Install the driveside cup and tighten it to 35Nm Connect the bottom bracket/torque sensor cable.
LOFT GO! 7D EQ Battery: remove AUTHORIZED DEALERS ONLY: Only authorized dealers should perform service on the e-system. Improper handling, tools used, or torque applied to these parts may result in damage to the e-system components and cables. Remove the torque sensor (see page 7). Rotate the bicycle and slide the battery assembly out.
LOFT GO! 7D EQ Battery: install AUTHORIZED DEALERS ONLY: Only authorized dealers should perform service on the e-system. Improper handling, tools used, or torque applied to these parts may result in damage to the e-system components and cables. Attach the controller to the battery (if necessary). Reconnect all cables and insert them into the bottom bracket shell.
Page 14
LOFT GO! 7D EQ Headset: Step-Over Compression bolt Top cap W545877 Compression nut (1 1/8”) Stem Upper headset bearing assembly W290398 30mm Lower headset bearing Optional spacers *Fork, Black Mercury (273mm) — 5296433 *This is a color-matched part — search trekbikes.com find the right color for your bike.
Page 15
LOFT GO! 7D EQ Headset: Step-Thru Stem plug Stem bolt W5285402 Compression nut (1 1/8”) 16.3-19Nm Quill stem (100mm) Upper headset bearing assembly, black W5257872 Lower headset bearing *Fork, Cloud Pink (219mm) — 5296441 *This is a color-matched part — search trekbikes.com find the right color for your bike.
Page 16
LOFT GO! 7D EQ Chainguard Bolts (M5x8mm) — W549307 Washers (M5) — W521137 *Chainguard, Black Mercury — 5296413 *This is a color-matched part — search trekbikes.com find the right color for your bike.
LOFT GO! 7D EQ Front fender Strut — W5288487 Split washers (M5) Fork crown shim — W5288528 Washers (M5) — W521137 *Front fender, Black Mercury — 5296421 Bolt, T25 (M5x25mm) *This is a color-matched part — search trekbikes.com Bolt, T25 (M5x14mm) 5308020 find the right color for your bike.
Need help?
Do you have a question about the LOFT GO! 7D EQ 2023 and is the answer not in the manual?
Questions and answers