Table of Contents
Advertisement
Brad Nailer/Stapler
(Models DBN125,
DBS125, DNS100)
Model DBN125 Shown
PART NO. A04051 - 04-16-04
Copyright © 2004 Delta Machinery
ESPAÑOL: PÁGINA 15
To learn more about DELTA MACHINERY
FRANÇAISE : PAGE 27
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call
Advertisement
Table of Contents
Related Manuals for Delta ShopMaster DBN125
Summary of Contents for Delta ShopMaster DBN125
- Page 1 Model DBN125 Shown PART NO. A04051 - 04-16-04 Copyright © 2004 Delta Machinery ESPAÑOL: PÁGINA 15 To learn more about DELTA MACHINERY FRANÇAISE : PAGE 27 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).
- Page 2 Date of Manufacture:___________________________ Fecha de fabricación:, Date de fabrication: Serial No:______________________________________ Número de serie:, Nombre d'ordre...
-
Page 3: Safety Guidelines - Definitions
If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you. Online contact form at www.deltamachinery.com Postal Mail: Technical Service Manager... -
Page 4: General Safety Rules
GENERAL SAFETY RULES 1. Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Fig. 1. 2. Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87”... - Page 5 Fig. 8. 15. Do not use tool without safety warning label. If label is missing, damaged or unreadable, contact your Porter-Cable •Delta Service Center for a replacement. Fig. 9. 16. Only use parts, fasteners and accessories approved by Delta Machinery.
- Page 6 21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool.
-
Page 7: Employer's Responsibilities
" to 1 the side. Delta Model DBS125 is designed as a 2 in 1 tool to install 18 ga. brad nails of various lengths from lengths from " to 1" long. Brad nails are loaded into the magazine from the side and narrow crown staples are loaded into the magazine from the top. -
Page 8: Preparing The Tool
PREPARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Depress latch and slide magazine cover open (Fig. 19). 3. Insert a strip of approved fasteners (Fig. 20 and/or Fig. 20A). Orient fasteners with points down in the magazine. -
Page 9: Using The Tool
OPERATING INSTRUCTIONS USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a “single sequential actuation” trigger. To fire, grip the tool firmly to maintain control, position nose of tool onto work surface, push the tool firmly against work surface to depress safety (S) Fig. - Page 10 The depth to which a fastener is driven is controlled by the depth adjustment knob (A) Fig. 25. The depth of drive is factory adjusted to a nominal setting. Test fire a fastener and check depth. If a change is desired, rotate the adjustment knob (A) Fig.
-
Page 11: Clearing A Jammed Fastener
CLEARING A JAMMED FASTENER Disconnect tool from air supply. Open magazine and remove remaining fasteners (Fig. 28 and Fig. 29). Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shoot out of magazine which could cause injury. Open the quick release latch and the fastener guide plate (Fig. -
Page 12: Maintenance
Keep all screws tight. Loose screws can cause personal injury or damage tool. If tool is used without an in-line oiler: place 5 or 6 drops of Delta Air Tool Oil into the air inlet of the tool at the beginning of each workday. -
Page 13: Troubleshooting
Put 5 or 6 drops of oil into air inlet. Install Overhaul Kit. Tighten screws. Install Overhaul Kit. Verify approved fasteners of correct size. Replace w/undamaged fasteners. Tighten screws. Clean magazine. Install “DRIVER” Maintenance Kit. Contact a Porter-Cable/Delta Service Facility. - Page 14 • Delta recommended accessories should be used with this product. Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven...
- Page 15 Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will be directed to the nearest Porter-Cable •...