Table of Contents
Troubleshooting
Related Manuals for pellenc 250
Summary of Contents for pellenc 250
- Page 1 Translated from original operating instructions manual Translated from the original operating instructions PELLENC BATTERY 56_158890-D Operating Instructions 05/2024 READ THE USER OPERATING GUIDE CAREFULLY BEFORE USE...
-
Page 3: Table Of Contents
2. SAFETY ........................... 6 2.1. SAFETY MEASURES ASSOCIATED WITH THE USE OF THE TOOL ......... 2.2. SAFETY MEASURES ASSOCIATED WITH BATTERY USE ............2.3. SAFETY MEASURES WHEN USING THE "PELLENC" CHARGER ..........2.4. SAFETY SIGNS ..........................3. DESCRIPTION AND TECHNICAL FEATURES ..............10 3.1. - Page 4 PELLENC BATTERY 250 56_158890-D 9. ACCESSORIES AND CONSUMABLES ................27 9.1. OPTIONAL ACCESSORIES ......................10. WARRANTIES ........................28 10.1. GENERAL WARRANTIES ......................10.1.1. STATUTORY WARRANTY ......................10.1.2. PELLENC COMMERCIAL WARRANTY ................... 10.1.3. PAID AFTER-SALES SERVICE ...................... 11. STATEMENTS OF COMPLIANCE ..................31 11.1.
-
Page 5: Introduction
56_158890-D 1. INTRODUCTION Dear Customer, Thank you for purchasing your PELLENC battery 250. Properly used and maintained, this equipment will give you years of satisfaction. Warning In accordance with product liability laws, we are not responsible for damage caused by our product if the product includes an accessory that is not from the manufacturer or is not approved by the manufacturer. -
Page 6: Safety
• Battery alone: product that is classified as class 9, UN3480. 14. Use of a battery other than that provided by Pellenc SA is dangerous (risk of serious injury). If a different battery is used, Pellenc SA cannot be held responsible for any consequences. -
Page 7: Safety Measures When Using The "Pellenc" Charger
In the event of contact with eyes, seek professional medical help. The liquid leaking from the batteries can cause irritations or burns. 19. Pellenc power tools must only be used with the battery units designed for the purpose. Use of other battery units can present a risk of injury and fire. -
Page 8: Safety Signs
PELLENC BATTERY 250 56_158890-D 2.4. SAFETY SIGNS California State Proposition 65: Caution This product contains or emits a chemical recognized by the State of California to cause cancer, birth defects or other reproductive harm. Tool compliant with Tool compliant with Moroccan standards. - Page 9 PELLENC BATTERY 250 56_158890-D The RBRC™ sticker (found on the packaging) indicates that PELLENC voluntarily participates in an industry program for the collection and recycling of used batteries in the United States and Canada.
-
Page 10: Description And Technical Features
PELLENC BATTERY 250 56_158890-D 3. DESCRIPTION AND TECHNICAL FEATURES 3.1. DESCRIPTION Battery HMI (Human-Machine Interface) Right connector: reserved for pruning shears Decrease button Charging connector Left on/off buttons Left connector: for 1.2 kW tools only Right on/off buttons Protective cap for the left connector... -
Page 11: Technical Characteristics - Charger
Commercial reference of the charger 132658 Tension 100-240V ~50/60Hz Class II Charging voltage 50,2 V DC Charging current 1 A dc maximum Charge percentage Type of charger 250 battery charging time 250 battery 4 hr Charger CB5010HV (1 A) 100%... -
Page 12: Start-Up
PELLENC BATTERY 250 56_158890-D 4. START-UP 4.1. FITTING THE BATTERY ON THE HARNESS Note The following procedure is valid for the purchase of a single battery delivered not fitted on the harness. Fitting the battery (1) on the harness (2). -
Page 13: Charging The Battery
PELLENC BATTERY 250 56_158890-D Note The power-on LED lights up when the power is turned on and goes out when the power is turned off. For more information about switching on and off with both tools, see 5.1. Usage method with both tools, page 4.3. -
Page 14: Hmi Display
PELLENC BATTERY 250 56_158890-D When the gauge display (6) flashes, the battery is charging. The charging is finished when the message appears on the gauge display (6) and the charger LED (2) is solid green. Once the battery is charged, first disconnect the charging cord (3) from the battery and then the mains plug from the charger (1). - Page 15 PELLENC BATTERY 250 56_158890-D Install the holster (3) on the harness. Position the hook-and-loop strap (1) on the holster (3). Slide the end of the hook-and-loop strap (1) into the belt loop (2). Pull and attach the hook-and-loop strap (1).
-
Page 16: Tool Connection
PELLENC BATTERY 250 56_158890-D 4.6. TOOL CONNECTION Note For more information on connecting the tool to the battery, refer to the tool's operating instructions manual. 4.7. PUTTING THE LEAD AND ARMBAND IN PLACE Put on the harness and install the connected tool in the holster, see 4.5. -
Page 17: Use
Left side: For 1.2 kW tools only. Right side: For pruning shears only. • To start your pruning shears PELLENC, turn on the battery by pressing the ON/OFF button (1) for 1 s, the red LED (2) will light up, and then the battery will beep . -
Page 18: Authorisation Modes
PELLENC BATTERY 250 56_158890-D The green LED (4) will light up steady if the pruning shears are not connected to the battery. Important If there is no connector connected, it is imperative to put the protective cap on (otherwise there will be electrical malfunctions). -
Page 19: Presentation Of Authorisation Modes
PELLENC BATTERY 250 56_158890-D 5.2.2. PRESENTATION OF AUTHORISATION MODES You can set the parameters for the tool's adjustment level to make it easier to use. • L1: Normal" mode: the user has access to the operating modes but no "functional" adjustments are possible. -
Page 20: Maintenance
Battery check by a PELLENC authorised distributor Important Have the battery serviced every 400 hours or at least once a year by a PELLENC authorised distributor. Always store the charged and clean battery in a dry place. 6.2. CLEANING THE BATTERY Make sure the battery is switched off, see 4.2. -
Page 21: Cleaning The Charger
PELLENC BATTERY 250 56_158890-D 6.3. CLEANING THE CHARGER Ensure that the charger is unplugged and disconnected from the battery. Clean the charger housing with a soft damp cloth. Important Cleaning shall be carried out with water only and without detergent, chlorine or sterilising solutions with an... -
Page 22: Incidents And Troubleshooting
PELLENC BATTERY 250 56_158890-D 7. INCIDENTS AND TROUBLESHOOTING 7.1. RECAP OF BATTERY DISPLAY MESSAGES AND AUDIBLE SIGNALS Normal messages Battery charge level (0 to 99) fixed Battery empty, recharge immediately with 1 beep per minute Stop using, recharge immediately. flashing with 1 beep every 10 seconds Only on ALPHA batteries connected to an ALPHA Tool. - Page 23 PELLENC BATTERY 250 56_158890-D Fault messages Voltage too low after 3 hours of non-use. Recharge the and 1 beep every 2 minutes for 24 hours battery immediately. Electronic board out of order Short circuit on the tool connector Long beep and 5 short beeps...
-
Page 24: Troubleshooting
PELLENC BATTERY 250 56_158890-D 7.2. TROUBLESHOOTING Caution Never attempt to open or repair the battery pack or the charger... -
Page 25: Battery Replacement
PELLENC BATTERY 250 56_158890-D 7.3. BATTERY REPLACEMENT Important The battery must be replaced only by an approved distributor. -
Page 26: Storage And Transport
PELLENC BATTERY 250 56_158890-D 8. STORAGE AND TRANSPORT 8.1. BATTERY STORAGE CONDITIONS • Store the “battery pack” and the charger away from heat, dust and humidity, after having switched off the battery see 4.2. Switching the battery on and off, page 12. -
Page 27: Accessories And Consumables
PELLENC BATTERY 250 56_158890-D 9. ACCESSORIES AND CONSUMABLES 9.1. OPTIONAL ACCESSORIES Name Reference Charger CB5010HV (1A) 132658 Adjustable harness 154702 Note Only if 250 battery purchased alone... -
Page 28: Warranties
10.1.2.1. CONTENTS 10.1.2.1.1. GENERAL INFORMATION In addition to legal warranties, client users benefit from the commercial warranty on PELLENC products covering the exchange and replacement of parts recognised as being out of order, due to machining defects, assembly defects or material defects, whatever the cause. -
Page 29: Paid After-Sales Service
PELLENC products are guaranteed under the commercial warranty as from delivery to the customer for a period of two (2) years for products connected to a PELLENC battery, and for a period of one (1) year for other PELLENC products. - Page 30 Paid after-sales service also covers PELLENC original spare parts, excluding labour and outside the legal and commercial warranty period. In case of replacement of original PELLENC spare parts in the context of after-sales service, said latter are covered by a warranty of one year as from the installation date.
-
Page 31: Statements Of Compliance
MANUFACTURER / PERSON AUTHORISED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) GENERIC DENOMINATION BATTERY FUNCTION Intended to power PELLENC portable power tools COMMERCIAL NAME ULTRA LITHIUM BATTERY TYPE Li-ion battery MODEL SERIAL NO. 26Y00001 - 26Y49999... -
Page 32: Declaration Of Conformity
THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the machine referred to below as: GENERIC DENOMINATION BATTERY FUNCTION Intended to power PELLENC portable power tools COMMERCIAL NAME ULTRA LITHIUM BATTERY TYPE Li-ion battery MODEL SERIAL No. - Page 36 PELLENC Quartier Notre Dame - 84120 Pertuis (France)
Need help?
Do you have a question about the 250 and is the answer not in the manual?
Questions and answers