MTD Yard Machines A500A Operator's Manual
  1. Manuals
  2. Brands
  3. MTD Manuals
  4. Log Splitter
  5. Yard Machines A500A
  6. Operator's manual
MTD Yard Machines A500A Operator's Manual

MTD Yard Machines A500A Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
M
PERATOR'S
ANUAL
LOG SPLITTER
MODEL
500
Model A500A
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO. 770-0364A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Yard Machines A500A and is the answer not in the manual?

Questions and answers

Related Manuals for MTD Yard Machines A500A

Summary of Contents for MTD Yard Machines A500A

  • Page 1 Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722. MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A.

  • Page 2: Section 1: Important Rules For Safe Operation

    SECTION 1: IMPORTANT RULES FOR SAFE OPERATION WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR LOG SPLITTER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
  • Page 3 • Both ends of each log must be cut as square as • Always keep fingers away from any cracks that possible to help prevent the log from riding out of open in the log during splitting operation. They can the splitter during operation.
  • Page 4 adding to the width or height of the wedge. Such pressure by shutting off the engine and moving the alterations may cause your splitter to be unsafe. control handle back and forth several times. • Perform recommended maintenance • Do not remove the cap from the hydraulic tank or procedures before you use your splitter.

  • Page 5: Section 2: Important Information For Log Splitter Users

    • Attempt to cut wood across the grain SECTION 3: FINDING YOUR MODEL NUMBER This Operators Manual is an important part of your you need help from your dealer or the MTD new log splitter. It will help you assemble, prepare customer support department.

  • Page 6: Section 4: Calling Customer Support

    SECTION 4: CALLING CUSTOMER SUPPORT If you are having difficulty assembling this product call the Customer Support Department. You can or if you have any question regarding the controls, reach them by calling: operation or maintenance of this log splitter, please 1-800-800-7310 Before you call, make sure that you have both your and serial number ready, you help the Customer Sup-...

  • Page 7: Section 6: Items Required For Assembly

    SECTION 6: ITEMS REQUIRED FOR ASSEMBLY DESCRIPTION Crowbar or Large Screwdriver Soft Hammer or Mallet 9/16" Wrenches* • Engine Oil 1/2" Wrenches* • Unleaded Gasoline 7/16" Wrench* 13/16” Wrench* • Dexron III Automatic Transmission Fluid or 7/8” Wrench* 10W Non-Foaming Hydraulic Fluid Adjustable Wrench Screwdriver Pliers...

  • Page 8: Section 8: Assembly

    SECTION 8: ASSEMBLY ASSEMBLING THE TONGUE Beam Support Latch Bracket Tongue Ball End Of Hitch Hitch Jack Stand Figure 2 The hardware that is used to assemble the tongue ASSEMBLY C (See Figure 2) will be found in place on the tongue and hitch. The Attach the hitch as follows: assembly has been divided into three assemblies A, 1.
  • Page 9 ASSEMBLING THE WHEELS, BEAM AND TANK Beam Axle Tongue Reservoir Tank Wheel Figure 3 The hardware that is used to assemble the wheels, 5. Place one flat washer (C) just removed on each beam and tank will be found in place on the tank or axle.
  • Page 10 ASSEMBLY B (See Figure 3) 2. This step will require two people. Stand the wedge, beam and cylinder assembly upright, Attach the tongue as follows: with cylinder to the top. 1. Remove the two hex bolts (I), lock washers (J) WARNING: Use extreme caution as and hex nuts (K) on the front of the reservoir...

  • Page 11: Section 9: Controls

    PREPARING THE ENGINE NOTE: There are two reservoir tank capacities depending on the log splitter model. The large tank 1. Place the log splitter on a firm, level surface. has a capacity of approximately 7 gallons. 2. Fill engine with oil as instructed in the separate small tank has a capacity of approximately 4 engine manual packed with your log splitter.

  • Page 12: Section 10: Operation

    SECTION 10: OPERATION BEFORE EACH USE 6. When necessary to stabilize the log, place your hand only on sides of log, NEVER on the end 1. Remove the vent plug and check the fluid level. between the log and splitting wedge. Fluid level should be 1-1/2"...
  • Page 13 OPERATING POSITIONS VERTICAL HORIZONTAL Beam Locks Figure 5 * * Figure 5 shows optional fenders not all unit are CONTROL HANDLE POSITIONS equipped with fenders. • Move control handle FORWARD or DOWN to split wood. VERTICAL • Release the control handle to stop the wedge •...

  • Page 14: Section 11: Adjustments

    SECTION 11: ADJUSTMENTS WARNING: Adjust wedge plate as follows: Always stop the engine and disconnect the spark plug wire 1. Loosen the three hex bolts on top of the wedge before performing any adjustments. plate (beneath the splitting wedge). 2. Loosen the jam nuts on the two adjustment bolts on the side of the gib plate, located Attached beneath...
  • Page 15 BEAM AND SPLITTING WEDGE 2. Drain gasoline from fuel tank or place a piece of plastic film underneath the gas cap to prevent Lubricate both sides of the beam where it contacts gasoline from leaking. the splitting wedge with engine oil before each use 3.

  • Page 16: Section 13: Off-Season Storage

    SECTION 13: OFF-SEASON STORAGE If the log splitter will not be used for a period longer 3. Wipe unit with an oiled rag to prevent rust, than 30 days, the following steps should be taken to especially wedge and beam. prepare the log splitter for storage.

  • Page 17: Section 15: Hydraulic Trouble Shooting Guide

    SECTION 15: HYDRAULIC TROUBLE SHOOTING GUIDE Trouble Possible Causes Corrective Action Cylinder rod will Broken drive shaft. Return unit for authorized repair. not move Shipping plugs left in hydraulic hoses. Disconnect hydraulic hoses, remove shipping plugs, reconnect hoses. Set screws in coupling not See operator’s manual for correct adjustment.

  • Page 18: Section 16: Illustrated Parts List

    SECTION 16: ILLUSTRATED PARTS LIST...
  • Page 19 REF. PART CODE DESCRIPTION REF. PART CODE DESCRIPTION 712-0359 Slotted Nut 3/4-16 Thd. 736-0116 Fl-Wash. .635" I.D. x .93" O.D. 714-0162 Cotter Pin 5/32" Dia. x 1-1/4" Lg. 736-0169 L-Wash. 3/8" I.D.* 734-0873 Hub Cap 736-0185 Fl-Wash. .406" I.D. x .75" O.D. 734-1016 Wheel Ass’y.
  • Page 20 United within the United States of America, its possessions States of America, its possessions and territories, and territories, MTD PRODUCTS INC will, at its except those sold through MTD PRODUCTS INC’s option, repair or replace, for the original purchaser, authorized channels of export distribution.

This manual is also suitable for:

Yard machines 500

Table of Contents