Table of Contents
Advertisement
Quick Links
InHand Networks
Edge Computing Gateway
IG902-FQ39
Quick Installation Manual
InHand Networks
www.inhandnetworks.com
Version: V1.0
February, 2019
Copyright © 2019. All rights are reserved by InHand Networks and its licensors. Without
the written permission of the Company, no unit or individual is allowed to excerpt,
reproduce or transmit in any form part or all of the contents in the manual.
Advertisement
Table of Contents
Related Manuals for InHand IG902-FQ39
Summary of Contents for InHand IG902-FQ39
- Page 1 Version: V1.0 February, 2019 Copyright © 2019. All rights are reserved by InHand Networks and its licensors. Without the written permission of the Company, no unit or individual is allowed to excerpt, reproduce or transmit in any form part or all of the contents in the manual.
-
Page 2: Table Of Contents
Content 1. Preface ............................... 1 2. Packing List ...............................1 2.1. Panel ................................. 2 2.2. Structure and Dimensions ..........................3 3. Installation ..............................4 3.1. Installing and Uninstalling the Device on a DIN-Rail ..................4 3.1.1. Installing with a DIN-Rail ........................4 3.1.2. Uninstalling with a DIN-Rail ......................4 3.2. -
Page 3: Preface
Each edge computing gateway product is delivered with accessories (such as standard accessories) frequently used at the customer site. Check the received product against the packing list carefully. If any accessory is missing or damaged, contact the InHand sales personnel promptly. -
Page 4: Panel
2.1.Panel Figure 2- 1 Caution The IG900 series product is applicable to multiple panel appearances, as they have the same installation method. Refer to the actual product during operation. -
Page 5: Structure And Dimensions
2.2. Structure and Dimensions Device size（Unit: mm） Track mounting size （Unit: mm） Wall mounting size （Unit: mm） Figure 2- 2 Structure size... -
Page 6: Installation
3. Installation Precautions: Power supply requirements: 12 V DC (12–48 V DC). Pay attention to the voltage class. The rated current is 0.6 A (1.2–0.3 A). Environment requirements: operating temperature –25°C to 75°C; storage temperature –40°C to 85°C; relative humidity 5% to 95% (non-condensing). The temperature on the device surface may be high. -
Page 7: Installing And Uninstalling The Device In Wall-Mounted Mode
Step 2: Revolve the device in the direction indicated by arrow 2, and grab the lower end of the device and move the device outward. Lift the device when its lower end isolates from the DIN rail. Then, take off the device from the DIN rail. Figure 3- 2 DIN rail disassembly schematic diagram 3.2.Installing and Uninstalling the Device in Wall-mounted Mode... -
Page 8: Uninstalling In Wall-Mounted Mode
Step 3: Take out the screws (packaged with the wall mounting bracket), fasten the screws in the installation positions by using the screwdriver, and pull down the device to make it secure, as shown in Figure 3-4. Figure 3- 4 Wall mounted installation diagram 3.2.2. -
Page 9: Installing The Power Supply
3.4.Installing the Power Supply Procedure: Step 1: Remove the terminal from the gateway. Step 2: Unfasten the locking screw on the terminal. Step 3: Connect the power cable to the terminal and fasten the locking screw. 3.5.Installing the Ground Protection Procedure: Step 1: Unfasten the ground screw cap. - Page 10 power Reserved(RS232) Reserved(RS485) Screws Figure 3- 9 Terminal line Note This section is only applicable to IG900 with industrial interfaces.
-
Page 11: Configuring Network Connection For A Wireless Gateway
4. Configuring Network Connection for a Wireless Gateway 4.1.Connecting to the Gateway Set the IP address of the management PC and the IP addresses of the GE interfaces of the gateway to be in the same network segment. The gateway has two GE interfaces: GE0/1 and GE0/2. -
Page 12: Quick Start Guide
Caution By default, the DNS of the PC connected to GE0/1 cannot use the IP address of GE0/1; otherwise, public domain names cannot be accessed. You can enable the DHCP server or configure another DNS for public domain name access. 5. -
Page 13: Importing And Exporting Configuration
Step 4: Press and hold the Reset button again when the ERR indicator is turned off several seconds later. Step 5: Release the Reset button when the ERR indicator blinks. The default settings are restored successfully if the ERR indicatoris turned off later. 5.2.Importing and Exporting Configuration Log in to the web page and choose Administration>Config Management in the navigation tree to access the Config Management page. -
Page 14: Panel Indicators
Figure 5-3 System log 6. Panel Indicators 6.1.LED Indicator STATUS WARN STATUS WARN SIM1 SIM2 SIM1 SIM1 SIM2 MODEM MODEM USER1 USER2 USER1 USER2 PYTHON WIFI PYTHON WIFI Booting up Boot up successfully STATUS WARN STATUS WARN SIM1 SIM2 SIM1 SIM1 SIM2 MODEM... - Page 15 Note Two SIM card indicators are provided. The indicator for SIM card 1 is turned on during the startup process and when startup is successful. In the last four situations, the indicator for the used SIM card is turned on. The following figure shows the indicator for SIM card 1.
- Page 16 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 17 IC STATEMENT This device complies with Industry Canada license-exempt RSS standard(s): Operation is subject to the following Two conditions: (1) this device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Need help?
Do you have a question about the IG902-FQ39 and is the answer not in the manual?
Questions and answers